Release Notes/Solved items Version 2021.1

RadiMation version 2021.1.10

• #11501: Driver: R&S RTE1024 as powermeter
• #11503: Driver: BLMA 0118-1A.
• #11506: Driver: Driver: IFI T82-250
• #11658: ErrorReport: "Teseq NSG3040: Device returned Error code: 13"
• #11801: RTO2024 - Leveling time and Voltage measurement error.
• #11839: Device driver for Rohde&Schwarz FSV3000 Spectrum Analyzer
• #11883: Driver: AR125S1G6
• #11886: The device driver system is currently not usable.
• #11903: RadiMation stops on initialisation
• #11904: IFR2025 High power option.
• #11906: Driver: RS FSVA 3044.
• #11916: Device driver: Amplifier BBA150BC500
• #11917: Device driver: AmplifierBBA150D200
• #11918: Device driver: Amplifier BBA150E100
• #11921: Prana N-MT 1650 DC
• #11923: Driver: TESEQ KEMA801A
• #11925: Device driver LISN TESEQ ISN-T8
• #11926: Device driver LISN EMTEST DCD-sr
• #11927: Device driver LISN EMTEST DCD-st
• #11934: Device driver: Antenna SAS-521F-7
• #11935: Driver: Modulation source Tektronix AFG3102
• #11942: Driver: Antenna Schwarzbeck VULB9164
• #11949: VI powermeter envelope tracing mode issues in new version
• #11956: RE: Switch-Matrix TESEQ RFB2000 - Inbetriebnahme in RadiMation
• #11960: ErrorReport: "CE met Peak en AV trace" measuring time changed from 200 ms to 10 ms
• #11963: Radimation/Lumiloop error during field probe mode switch
• #11968: R&S NRP18A time-out when using high filter count.
• #11980: ErrorReport: "layout of emission plots"
• #11984: RadiPower advanced option to configure the used VBW during remote measurement
• #11985: Test level input should disable tolerance
• #11997: R&S NRP-Z91 Powermeter confused.
• #12000: amplifier linearity check - forward power step issue
• #12003: ErrorReport: "EFT test sequnce does not run"
• #12005:Device driver for EM-Test NX7 with DCD Burst coupling network
• #12006: RadiMation Help button redirects to Dare.eu instead of Raditeq.com
• #12018: ErrorReport: "Rohde & Schwarz RTO2024 (CH2): Specific System Error: -222,"Data out of range;CALC:MATH2:FFT:STAR 70698577.88"".
• #12036: Report Generator Harmonics & compression not inserted
• #12057: ErrorReport: "FM modulation multiband could not be set"

RadiMation version 2021.1.9

• #11666: ErrorReport: No Tooltip found for buttons placed on the graph control
• #11693: AW: Report Generator - keyword Frequency Step and Modulation does not work
• #11743: ErrorReport: "rbw coupling error" on HP 7405 analyser.
• #11746: ErrorReport: "Can't auto couple sweep time in zero span" on HP 7405 analyser.
• #11779: wxWidgets Debug Alert
• #11782: Driver: Teseq CBA 1G-600D.
• #11789: Editing a limit line value initially shows the unit default value scaled to the new selected unit
• #11790: VI instrument time index axis is not updated for the additional time measured
• #11791: Using SQL to format a custom peak table including frequency data adds the _RAW frequency column data instead.
• #11792: RadiTower unnecessary moved to 4M after measuring at 1m
• #11793: Error Start frequency is too low for selected equipment, when viewing the data of two tests simultaneously
• #11794: RI Graph, no filter at top of the Graph
• #11798: Graphs settings, Frequency Range/Scaling not possible.
• #11813: Cannot connect to Frankonia FC03 antenna tower controller
• #11816: Using order by clauses on table names results in the table not being found when the unit is missing in the keyword
• #11817: 0,5 kV is not selectable in the EFT manual mode test
• #11819: ESW8 Measuring input 2 @1 GHz results in error -222 data out of range
• #11820: Using a <CUSTOM> field in the EUTInfo.ini results in the input being shifted when shown in RadiMation
• #11826: During test initialisation a "Pause" window before action is not shown to the user
• #11832: limit lines is using a wrong x axis scale.
• #11833: Error report improvements.
• #11838: Device driver for Rohde&Schwarz SMBV100B Signal Generator
• #11839: Device driver for Rohde&Schwarz FSV3000 Spectrum Analyzer
• #11840: Incorrect step frequency in immunity.
• #11841: Peak number not visible in graph.
• #11849: Reporting of antenna height incorrect during test and in review
• #11852: Manual clamp mover driver is reporting the distance in degrees instead of centimeters
• #11853: Manual clamp mover driver shows the distance in on 0.001 mm accuracy, which is just unlogical
• #11859: RI logarithmic "Frequency Step" not possible to set smaler than 1%"
• #11863: Tooltip of shown peaks uses incorrect text, higher\lower then should be higher\lower than
• #11866: NSG4070 Does not power on at start of test.
• #11871: TESEQ NSG 3040: Device returned Error code: 19.
• #11872: NSG4070 failure?
• #11884: Number of peaks not correctly applied
• #11888: Peak detection absorbing clamp test
• #11889: Radilog becomes unresponsive and freezes Radimation, when monitor inputs are measured during MB Pulsed testing.
• #11890: ESW8 1000 kHz not possible with QP.
• #11878: Out of memory exception while doing EUT Save As...

RadiMation version 2021.1.8

• #11504: Driver: Solar Electronics 2352-1.
• #11505: Driver: Teseq CBA-series amplifiers.
• #11660: Driver: Comtest Engineering MCP-01 switch matrix
• #11755: Driver: Bonn BLMA 2060-50 Band 1 to 5
• #11777: Driver: PMM Antennas.
• #11780: Driver: EMC Shop DC1G-1000A coupler.
• #11781: Driver: EMC Shop DC6G-250.
• #11788: Export limitline graph as table in test with Frequency unit as kHz raises Frequency too large exception
• #11796: Duty cycle is not visible in Burst measurement.

RadiMation version 2021.1.7

• #4525: Support the gated pulse modulation
• #11610: Driver: Boonton Power Meter 9241.
• #11714: Out of memory during printing
• #11716: Driver: Frankonia EFS-Laser
• #11753: Cable table column chooser is overwritten with the copy context menu

RadiMation version 2021.1.6

• #11664: Driver: R&S RTO2024 as a dual input powermeter/analyzer.
• #11673: Multiband immunity modulation configuration dialog is shown too small by default
• #11674: Warning regarding pulse time is still shown when PM is disabled
• #11675: Multiple messages in notification area of modulation configuration is are not readable.
• #11676: Up and down of the pulse gating repetition time are now working
• #11677: Modulation configuration error links to an unknown knowledgebase page
• #11692: Error cannot find signal generator in currently active test-site when changing the frequency of the powermeter
• #11706: ErrorReport: "Object name is shown instead of limit line value when trying to configure a limit line
• #11711: Index out of array
• #11713: Changed EUT details not stored when closing EUT file.

RadiMation version 2021.1.5

• #11684: Cannot enable modulation

RadiMation version 2021.1.4

• #11651: EUT Monitoring graphs are not shown in the frequency graph, but are available in the time graph

RadiMation version 2021.1.3

• #11617: No measurement results when using a frequency list.

RadiMation version 2021.1.2

• #11593: Out of memory exception raised while using CLI.
• #11598: Harmonics calibration based on field measurement is not able to use spectrum analyzer

RadiMation version 2021.1.1

• #42: Add EUT Monitoring Input support for the EFT, ESD and Surge tests
• #4161: Multiband power measurement seems to limit at -100 dBm
• #5807: The minimum value of the dBuV/m should be around -67 dBuV/m
• #5836: Lower the minimum values for magnetic fields to far below -100dBuA
• #10454: When reading out the data of the powermeter with a switch matrix it seems that it is uncorrected
• #10457: Importing EUT Data
• #11093: Average trace is not visible when below -100
• #11165: Project: Simplify copying of customer provided data into an EUT file.
• #11189: Send corrected forward power value to switch matrix
• #11214: min/max values and division marks are not shown during display of graphs
• #11340: Could not find default endpoint element that references contract 'RadiLogService.IRadiLogService' in the ServiceModel client configuration section.
• #11343: Unclear message: 'Please connect the powermeter to the power reference.' during amplifier compression system calibration test
• #11433: Item #154 -Loading the device driver list (amplifiers) is taking longer than expected
• #11435: Amplifier control window position is not remembered on restart
• #11436: Amplifier control window issues
• #11464: RadiMation installer must not install the example directory in the program files(86x) folder
• #11465: Changing the installation directory of RadiMation does not work.
• #11493: When using a R&S NRVD the frequency correction is not set to ON.
• #11528: Status of actual status of a multiband immunity test is not clear in the skinned version
• #11568: No graph for low frequent magnetic field emission measurement