Release Notes/Solved items Version 2015.2.5
Jump to navigation
Jump to search
RadiMation version 2015.2.5[edit]
- #470: No buttons present for often used operations
- #510: No overview of of used equipment at start of a test
- #5527: Label of Show details button should become Hide details when details are shown
- #5576: Driver: R&S OSP130 with option B102
- #5661: Add Frequency range panel for Bonn BLWA drivers
- #5985: ESR7 replies with error about AC_DC coupling on Channel2
- #6123: RadiMation is not responding when Amplifier Control window is enabled
- #6251: R&S ESR7 specific System Error: -222 Data out of Range DISP:TRAC:Y:RLEV:0.0103DBM
- #6270: Raise an error when R&S NRP-Z55 power sensor is disconnected during test
- #6296: Device stream in the device driver system for http protocol using get and post
- #6297: Driver: USB-xSPDT-A18 series switch matrix
- #6299: R&S FSP30 spectrum analyzer option for FFT filters
- #6302: Driver: Tektronix RSA5100-series
- #6312: Timeout in communication with R&S ESPI after QP measurement
- #6321: Clear the input buffer of a configurable device driver directly after the connection is established
- #6322: Not possible to specify the Escape character in the configurable device driver
- #6323: Configurable switch matrix device driver sends the 'Turntable Changed' command before the turntable starts moving
- #6340: No Unit is shown for test level
- #6343: Ability to disable determination of the dynamic range during the Attenuation / Gain system calibration
- #6345: Carrier Level command of the Configurable Signal generator is not transmitted if no Carrier On command is specified
- #6349: Driver Switch matrix ICS 4864
- #6349: Driver Switch matrix ICS 4864
- #6354: QP Detector Measuretime of ESL6 is set to 10 ms
- #6360: Driver: Tektronix 2001 for fixed voltage test
- #6361: Ability to zoom in the frequency graph during the prescan phase of a MB Emission test
- #6362: Frequency of the graph in the report is different
- #6364: Too few spaces in the name of the graphline in a report generator code causes that the graph is not include in the report
- #6389: Update the Configurable Switch Matrix wiki knowledgebase page
- #6394: NI DAQ USB 6218 AD Converter default input min and max
- #6395: NI DAQ USB 6218 AD Converter channels 9-16 can't be used
- #6396: NI DAQ USB 6218 AD Converter read values are delayed
- #6397: How to dirrectly reference from the Main Template to a Keyword for a certain test
- #6398: Driver: Tektronix TDS2024C Oscilloscope
- #6399: Driver: Tektronix AFG3252 Signal Generator
- #6400: Driver: IFI ST181-10 Amplifier
- #6403: Ability to use the FSV-3 Analyser controlled as powermeter in zero span mode
- #6405: ARFI7000 is not reading probe values
- #6410: Driver: ETS-Lindgren 8000-053 amplifier
- #6411: Driver: ETS-Lindgren 8000-034 amplifier
- #6412: Raise an error when R&S NRP-Z55 is disconnected during a test
- #6418: R&S FSV 40 Error -222: Data out of range DISP:TRAC:Y:RLEV -10 DBM
- #6426: Configurable Switch Matrix isn't correctly saving settings when user configured commands of During and/or After Test are cleared
- #6426: Configurable Switch Matrix isn't correctly saving settings when user configured commands of During and/or After Test are cleared
- #6428: Device driver Check is erasing the selected correction file(s) in the device configuration screen
- #6432: Device drivers that are using GPIBRS232 should be converted to panels
- #6436: Selection of a correction file in a device driver configuration is not working
- #6438: Default frequency range of the EMCO / ETS-Lindgren antenna 3117
- #6439: Driver: All ETS-Lindgren 8000-series amplifiers
- #6441: Frankonia FC is raising an -101 error during test initialization
- #6442: What does the NRP settling time does?
- #6448: Correct frequency range of the ETS-Lindgren 8000-034 amplifier
- #6453: Uniform Field Area (UFA) calculation should trigger a default auto-layout when calibrations are added or removed
- #6454: Not possible to use CAL files for the UFA when it contains different test distance
- #6459: ETS-Lindgren 8000-053 Device Not Connected
- #6462: How to set the RBW when the R&S FSP 40 is used as powermeter?
- #6465: Driver: ETS-Lindgren Antenna series
- #6467: Driver: R&S FSIQ 7
- #6471: 'Decrement' should be the default value for the PowerStep setting of the Amplifier Linearity test
- #6472: Settings that are normally protected for the administrator, can be changed when the dongle is not present
- #6474: After zooming in a graph the graph axis is no longer linked to center and span
- #6476: Save the configured Auto-Layout settings for the Uniform Field Area (UFA) calculation config
- #6477: Insert Row in a Correction file is not working if no row is present
- #6478: A new correction file should have 1 row by default
- #6479: A new row should be added to a correction file when the 'TAB' key is pressed in the last cell
- #6527: Ability to specify a frequency depending RBW for the R&S ESI Powermeter
- #6572: Show a message with the used coupling value for the virtual coupler