Difference between revisions of "Release Notes/Solved items Version 2021.3"

From RadiWiki
Jump to: navigation, search
Line 1: Line 1:
 +
{{:Release Notes/Solved items Version 2021.3.8}}
 
{{:Release Notes/Solved items Version 2021.3.7}}
 
{{:Release Notes/Solved items Version 2021.3.7}}
 
{{:Release Notes/Solved items Version 2021.3.6}}
 
{{:Release Notes/Solved items Version 2021.3.6}}

Revision as of 12:09, 19 May 2022

RadiMation version 2021.3.8

  • #11707: QP value of the final measurement is not updated in the peak table"
  • #11843: Regulation on Electrical Field closed loop measured by analyzer is regulating above testlevel
  • #11981: Datetime is shown in OLE format when inserting table into txt file
  • #11924: Device driver: NSG 4060
  • #11999: Switch-Matrix TESEQ RFB2000 "Incorrect switch settting"
  • #12220: Corrrection file frequency list does not take unit precision in considereation
  • #12273: Correction of spectum analyzer
  • #12298: Peak measurement of radiated emissions measurement is too high
  • #12345: EFT Multiband, stop and return to "Automatic" last test perform twice.
  • #12348: EFT Test: NX5, error before every start.
  • #12358: Surge, EM-Test NX5, EXT coupling not working.
  • #12414: High peaks during the conducted emission measurements
  • #12422: Polarization Incco 3000
  • #12466: 4395A spectrum analzyer read out error during CS test
  • #12475: 337 dBuV is returned when retreiving trace data
  • #12476: Radiated emission test failed.
  • #12477: Precision on Logaritmic frequency step
  • #12481: problems connecting to Filedsensor Raditeq RSS2010I
  • #12483: spectrum analyzer overflow
  • #12486: Timeout with configurable AD Converter
  • #12491: Probe rotator hangs while moving to 120 degrees
  • #12492: Detector is not correctly set.
  • #12495: NSLK8122RC controlled by ESR via radimation ????
  • #12497: Issues at KEMA with RadiSense field probe
  • #12500: Error of band selection
  • #12501: End frequency to high for used LISN driver
  • #12503: Error Detector CISPR Average
  • #12503: RadiMation automatic mode does not seem to measure all found peaks
  • #12505: Driver: Ametek NSG4060
  • #12508: Add reseller BluEmi
  • #12519: Check of the Yokogawa DL950 is always failing
  • #12525: RFB2000 not returning response on Pos:A and Pos:B
  • #12526: Teseq RFB2000 doesn't respond to queries
  • #12527: Teseq RFB2000 doesn't respond correctly on second test
  • #12532: Yokogawa DL950 is using SYST:ERR as an unknown command
  • #12535: Yokogawa Scopecorder DL950 returns Function not implemented for AD-Convertor
  • #12540: Yokogawa DL950 interprets channel number as the measurement value
  • #12547: Yokogawa DL950 Measuring Min and Max values
  • #12550: During burst crash
  • #12556: Add support for automatic HiSLIP
  • #12559: Tabor WW5061 initialisation error
  • #12560: Reflected power monitoring during forward power calibration
  • #12561: Measuring a value from the Yokogawa DL950
  • #12564: Tabor WW5061 Initialisation Error
  • #12570: Frankonia FC06.1 Antenna mast 1 polarization change
  • #12581: Termination settings are not forced on GPIB DeviceStream
  • #12590: Tabor WW5601 Error
  • #12590: Tabor WW5601 Set voltage does not match measured voltage
  • #12594: RadiMation freezes when configuring the RIGOL DSG815
  • #12599: device driver EM-Test NX7
  • #12608: Error during calibration (CI)
  • #12609: RPR2006C
  • #12611: Unable to set RBW in ESPI3 during Amplifier compression calibration
  • #12624: Preamplifier is not activated above 7 GHz on R&S ESI 26
  • #12650: Testlevel shown in linear interpolation.
  • #12668: Multiband of Absorbing clamp_not moving after 5meter.
  • #12726: Tektronix RSA306: Unexpected Windows error. Error code: 87
  • #12779: Radiapol error code 102

RadiMation version 2021.3.7

  • #10321: Driver: ETS-Lindgren: VisionTRX
  • #10322: Errorcodes for VisionTRX
  • #10323: VisionTRx optimization GetChannelValue function.
  • #11641: Alarm in channel in VisionTRX is not shown in RadiMation
  • #12353: Error modulation ON in conducted immunity
  • #12400: PC could not detect RPR2006C Power Sensor.
  • #12425: Error: Could not set value in device, After measuring peak
  • #12433: Limit line file units do not scale when changing the unit shown in the editorbox
  • #12454: Allow that \n as only terminator is used by mk messtechnik Motion detection
  • #12455: Extend the number of channels in mk messtechnik Motion from 4 to 16
  • #12456: Use a switchmatrix for the mk messtechnik Motion detection, to only have detection during the dwelltime
  • #12461: Error at second rotation of Frankonia FC05 turntable
  • #12474: 2021.3.6 version hangs during a singleband immunity test
  • #12518: ScopeCorder DL950 Driver is not responding on the LAN interface
  • #12530: Frankonia FC 06.1: Antenna polarization problem with Frimware V02.05.xx
  • #12549: Ladybug cannot be initialized
  • #12566: How to measure below 10 MHz with the R&S ESR
  • #12593: Unable to connect to RPR2006
  • #12598: USB connected RPR2006 is difficult to connect with a VISA stream
  • #12618: Amplifier research amplifier GPIB communication problem

RadiMation version 2021.3.6

  • #8094: Markers in MB Emission tests are shown twice
  • #8095: RadiGen RGN 4 kHz start frequency option
  • #11835: Update nlohmann json library C++
  • #12007: Driver: Tabor Electronics WW5061 signal generator
  • #12014: Device driver: R&S SMM100A
  • #12020: Signal Generator Rohde&Schwarz SMCV100B
  • #12061: RPC server unavailable + out of memory exceptions when generating reports
  • #12076: Generic limit line inclusion in generated reports for SB tests, such as EUT attenuation
  • #12166: Report generator add keywords "||<type> TEST LEVEL||" for multiband test levels
  • #12210: More digits (than in the past) for the fieldstrength are reported to CARAD
  • #12235: Driver: Teseo SOPM306L
  • #12264: Cannot change Baudrate of HI-6105 probe
  • #12330: Error during quasi measurement, because selecting AUTO RBW is not allowed
  • #12341: Antenna polarity changing problem controller FC06.1
  • #12342: The STOP button of the Antenna Height does not response for the Frankonia FC06.1
  • #12346: RI false peaks are detected for inputs not matching with the configured unit in the limit line
  • #12349: Amplifier linearity forward power step not calculated correctly
  • #12365: Radiated emission test is not working
  • #12366: Create the printout template for the calibration harmonics test.
  • #12369: Remove the ISXDL.DLL from DRIVERS.EXE
  • #12376: Read correct probe HW version
  • #12377: The STOP Button does not respond on the Frankonia FC06.1
  • #12379: Report generator: Excel hangs while generating report
  • #12380: Radiated Emission Error With RSA5065N
  • #12384: Error at end of peak measurement, because selecting AUTO RBW is not allowed
  • #12388: Unexpected invalid software key after new RadiMation install.
  • #12393: Sweeptime error.
  • #12394: SMA100A error
  • #12396: Error during final peak measurement.
  • #12397: Error during QP measurement.
  • #12398: Error during QP measurement.
  • #12411: Error about auto sweep time.
  • #12432: Stopping an AdvancedTurnTable device driver, starts moving again after stopping
  • #12435: Frankonia FC06 series returns polarization in degrees instead of radians
  • #12437: Read of SYST:ERR? from Frankonia FC series happens much later
  • #12445: Signal generator driver SMCV100B
  • #12450: SMA100A error

RadiMation version 2021.3.5

  • #12123: Support Windows 11
  • #12187: Investigate applying the 4 GB patch to the executable as a workaround for OutOfMemory exceptions
  • #12310: Antenna distance is very often reset to 1 cm in version 2021.3.1
  • #12339: Allow RI Magnetic field tests based on forward power
  • #12360: MB fixed forward power does not regulate to test level
  • #12386: Interpretation of the expected response of the configurable field probe is not working anymore
  • #12420: The INNCO CO3000 version 1.03.09 does not change the polarization of antenna
  • #12426: Singleband Fixed field test 80-1000MHz results in very low field
  • #12427: Connect RSS2010I from a VI window when testing raises ERROR 3
  • #12428: Test IEC 61000-4-3 at 30V/m at 3m following Calibration file is problematic
  • #12429: Fixed field without calibration regulated to 247 V/m
  • #12448: Error 451 at Marconi generator
  • #12451: can not export to excel

RadiMation version 2021.3.4

  • #12120: ErrorReport: "Peak detection and selection can be on a higher emission"
  • #12188: Not always the highest peak is selected
  • #12297: Frankonia FC06-1 Antenna mast communication problem
  • #12300: Test initialization error.
  • #12312: Frankonia FC 06.1 Controller Antenna mast error
  • #12313: Frankonia FC06.1 Turn table controller error
  • #12316: The antenna height increment of the Frankonia FC06.1 not work
  • #12317: Driver: Vectawave VBA230-80
  • #12318: Driver: Rigol DSG 815
  • #12320: Strange numbers on vertical scaling when using manual scaling
  • #12335: Error during radiated emission.

RadiMation version 2021.3.3

  • #11896: Send filename of test results to CARAD
  • #12305: An additional unlogical GPIB board is checked during startup
  • #12306: Bonn amplifier driver doesn't report description of basic errors

RadiMation version 2021.3.2

  • #1909: Use device driver out of default frequency range for similar models
  • #6006: Turn off of the continuous measure is not working if long observation times are used
  • #7222: Allow customization of the expected *IDN? response of drivers
  • #7500: Response errors detected during the check device should be shown to the enduser in the error description
  • #9106: Wrong device driver selected
  • #11740: Include prefix on the suggested name of the on the exported ambient line.
  • #11873: Manual Controlled AD converter is not working correctly anymore
  • #11987: When the *IDN? does not match we should show a correct message
  • #12215: ESIB Analyser Error: Not all bytes are written to the GPIB-Board within the timeout period
  • #12247: RadiMation Crash when using ESR for QP measurements
  • #12254: Issues with QP measurements too high on Rigol DSA832
  • #12277: Power measurement is reported twice by configurable switchmatrix in 2021.2.7
  • #12280: Driver: Keysight N9916B
  • #12284: Driver: Amplifier Prana N-MT 1650D
  • #12286: ForwardPowerMeasured event in switchmatrix is not raised for first 2 frequencies
  • #12288: Connect RSS2010I with radimation software
  • #12289: RadiSense 10 is not correctly detected

RadiMation version 2021.3.1

  • #11106: Vertical scaling does not adjust (30M-1G)
  • #11882: Graph ticks do not follow unit settings
  • #11931: Scaling of emission plots
  • #11951: Ongoing annoying issues with scaling of graphs
  • #11967: Onlogische schaalverdeling Y-as
  • #12024: Y-axis values are not displayed completely
  • #12062: Update reseller information of NSI-MI UK
  • #12085: ErrorReport: "Object reference error when creating correction files with 0.001 kHz frequencies"
  • #12132: clsSettingGraphDivisions object ID not registered
  • #12296: BONN BLWA amplifier initialization failed