Release Notes/Solved items Version 2021.3.8
RadiMation 2021.3.8
- #11707: QP value of the final measurement is not updated in the peak table"
- #11843: Regulation on Electrical Field closed loop measured by analyzer is regulating above testlevel
- #11981: Datetime is shown in OLE format when inserting table into txt file
- #11924: Device driver: NSG 4060
- #11999: Switch-Matrix TESEQ RFB2000 "Incorrect switch settting"
- #12220: Corrrection file frequency list does not take unit precision in considereation
- #12273: Correction of spectum analyzer
- #12298: Peak measurement of radiated emissions measurement is too high
- #12345: EFT Multiband, stop and return to "Automatic" last test perform twice.
- #12348: EFT Test: NX5, error before every start.
- #12358: Surge, EM-Test NX5, EXT coupling not working.
- #12414: High peaks during the conducted emission measurements
- #12422: Polarization Incco 3000
- #12466: 4395A spectrum analzyer read out error during CS test
- #12475: 337 dBuV is returned when retreiving trace data
- #12476: Radiated emission test failed.
- #12477: Precision on Logaritmic frequency step
- #12481: problems connecting to Filedsensor Raditeq RSS2010I
- #12483: spectrum analyzer overflow
- #12486: Timeout with configurable AD Converter
- #12491: Probe rotator hangs while moving to 120 degrees
- #12492: Detector is not correctly set.
- #12495: NSLK8122RC controlled by ESR via radimation ????
- #12497: Issues at KEMA with RadiSense field probe
- #12500: Error of band selection
- #12501: End frequency to high for used LISN driver
- #12503: Error Detector CISPR Average
- #12503: RadiMation automatic mode does not seem to measure all found peaks
- #12505: Driver: Ametek NSG4060
- #12508: Add reseller BluEmi
- #12519: Check of the Yokogawa DL950 is always failing
- #12525: RFB2000 not returning response on Pos:A and Pos:B
- #12526: Teseq RFB2000 doesn't respond to queries
- #12527: Teseq RFB2000 doesn't respond correctly on second test
- #12532: Yokogawa DL950 is using SYST:ERR as an unknown command
- #12535: Yokogawa Scopecorder DL950 returns Function not implemented for AD-Convertor
- #12540: Yokogawa DL950 interprets channel number as the measurement value
- #12547: Yokogawa DL950 Measuring Min and Max values
- #12550: During burst crash
- #12556: Add support for automatic HiSLIP
- #12559: Tabor WW5061 initialisation error
- #12560: Reflected power monitoring during forward power calibration
- #12561: Measuring a value from the Yokogawa DL950
- #12564: Tabor WW5061 Initialisation Error
- #12570: Frankonia FC06.1 Antenna mast 1 polarization change
- #12581: Termination settings are not forced on GPIB DeviceStream
- #12590: Tabor WW5601 Error
- #12590: Tabor WW5601 Set voltage does not match measured voltage
- #12594: RadiMation freezes when configuring the RIGOL DSG815
- #12599: device driver EM-Test NX7
- #12608: Error during calibration (CI)
- #12609: RPR2006C
- #12611: Unable to set RBW in ESPI3 during Amplifier compression calibration
- #12624: Preamplifier is not activated above 7 GHz on R&S ESI 26
- #12650: Testlevel shown in linear interpolation.
- #12668: Multiband of Absorbing clamp_not moving after 5meter.
