Release Notes/Solved items Version 2016.2.2

RadiMation version 2016.2.2

• #1688: Cannot save multiband test
• #3398: Test on hold when opening RE Multiband file
• #4074: Optimize angle is not measuring every area
• #4155: Device specific parameters are not retrieved when a device driver is created
• #4714: Cable loss correction applied to the Cable antenna Preamp is incorrect
• #4771: Adding cable with default port type value is not correct
• #4800: Comparing test data and zooming graphs in Multiband is not working
• #4823: CORrection factor current probe is not taken into account
• #4855: Possibility to directly open device driver TYPE window and TAB by just one click
• #4892: RM crash during RPR2006P Free mode when test equipment is opened
• #5222: Add a Virtual Instrument for the Amplifier
• #5223: Add a Virtual Instrument for the Signal generator
• #5270: Peak conservation setting is ignored for Singleband Radiated Immunity
• #5368: Graph data is not updated
• #5550: Add an 'Configure...' menu entry in all the sub-menus of the Devices menu
• #5565: Opening the virtual powermeter window shows a corrupt file error
• #6130: Device driver: emtest VCS 500
• #6228: Cable correction is not correctly taken into account during the Current Probe test
• #6421: Multiband graph is not exporting vertical and/or horizontal polarization graph
• #6667: Virtual Instruments should be able to collapse to a 'mini' mode that only shows the measurement value
• #6703: Driver: em test PFS 500
• #6704: Driver: em test MV2616
• #6705: Driver: emtest UCS500N5: voltage dips and interrupts support
• #6745: Include a 'Clear' button on the VI Fieldstrength sensor to clear the (time-)graphs
• #6746: Lower and upper value of the analog meter on the VI should be autoranging
• #6747: Show the 'table' tab for the time-graph in a virtual instrument
• #6749: Time graph in Virtual Instrument is using the wrong date
• #6750: Time graph of a Virtual Instrument should have a minimum time range of 30 seconds
• #7040: Marconi signal generator doesn't respond on *STB?
• #7065: A MB emission test shows a 'Fail', even if all emissions are below the limit
• #7102: Backwards sweeping is not correctly handled
• #7151: VDI: ProgressBar starts at 99%
• #7202: Longer time till sleep mode Narda EP600/EP601
• #7205: Default settings of Multiband EFT is not logical
• #7206: Default settings of Multiband Burst is not logical
• #7210: emtest PFS 500N Not all bytes are written
• #7213: Sequence are shuffled
• #7230: VIBase not always (dis)connecting
• #7231: Add suggested values
• #7234: Unit window showing example of setted settings.
• #7235: Clear Graph button in the VIBase is not correctly implemented.
• #7239: Unable to clear graph in VI windows while trigger is set to auto.
• #7250: Unit settings example is not correct with a precision of 0
• #7251: Unit settings applied to AnalogMeter control before init
• #7276: Unit settings are applied on fieldsensor not on the ctlAnalogDigitalMeter control itself.
• #7307: Error messages in the VI Powermeter are not shown
• #7327: Not controllable EFT and Surge device drivers should raise an error, early at the automated test
• #7328: Multiband EFT Test is in a continuous loop, when an error is raised
• #7335: Determined Forward power step during amplifier linearity is 100000 dB
• #7360: Calculated graph is recalculated 6x when an additional non-relevant graph is shown
• #7363: VIBase not always (dis)connecting
• #7364: 'Clear' button is hidden when the VI window is resized when the device is disconnected
• #7366: Resizing of 'Logging' tab of VI Powermeter is not done when another tab is active
• #7367: Tabs on the VI Powermeter should be hidden when the size of the window becomes too small
• #7368: Hide the analog meter if it becomes too small
• #7369: Improvements for the VI Turntable window
• #7370: Allow smaller size of VI Antenna tower
• #7371: A VI window should remember it's location and size
• #7373: RadiFree warnings
• #7374: Location and size of the window is not remembered if the RadiMation main window is closed with windows open
• #7375: Settings of the VI Signal generator are not set in the signal generator after a connect
• #7376: Clear button of a VI should also be enabled when the device is disconnected
• #7377: Clear button should be pressed automatically when the VI window is closed
• #7378: Only show the test initialization window if it contains more than 1 item
• #7380: Auto-Show and Auto-Connect for VI devices
• #7388: Resizing of the contents of the VI Powermeter window is incorrect
• #7389: Virtual Instrument window of the Virtual signal generator is always showing disabled controls
• #7391: Improve the showing of the 'Devices' menu
• #7396: RadiMation crashes during start with open automatically connecting VI windows
• #7410: Saving a test equiment with changing just 1 char to uppercase seems to overwrite the existing test equipment
• #7413: Unit Volts per meter shows only V
• #7417: Validation documentation of RadiMation
• #7429: Correction of Monitoring Input powermeter is also applied to the used (forward) powermeter during the test
• #7442: Invisible Clear Button
• #7443: Visible progress bar
• #7446: Reflected powermeter measurements data is incorrectly shown
• #7452: Improve the showing of the "Test-Site Menu"' menu
• #7453: Device menu also contains an Add Device button
• #7458: Address Information will pause a running test
• #7464: Name the log file the same as the subject description instead of always Last error report
• #7470: VI Signal Generator Carrier ON and OFF control has incorrect triggering
• #7507: Graphs are not drawn when 'Ramp' method is used in MB Immunity
• #7512: Virtual burst powermeter doesn't work anymore in RadiMation Free 'Burst' mode
• #7529: New testsites are shuffled in the Test-Sites list
• #7598: Error report, customer information is not remembered