Release Notes/Solved items Version 2017.2.10

RadiMation version 2017.2.10

• #5637: Excel Export error Object reference not set to an instance of an object
• #5832: Updated Radiwiki Agilent U2000 series page
• #5973: Absorbing clamp test raises System.OutOfMemoryException and crashes
• #5995: Shield to Ref. is not listed as a EFT cable test
• #6135: Driver: Teseq ITS6006 for IEC61000-4-3 & CISPR11 as Switch Matrix
• #6696: Driver: Schloeder SFT1400/SFT1420
• #6697: Driver: Schloeder CWG500
• #6979: Create a correct application manifest file for the executables
• #7035: Driver: Teseq ITS6006 functionalities for EUT monitoring interface
• #7706: Start and Stop frequency Report generator code behavior.
• #7949: Unable to select peaks from the graph
• #7997: Driver: R&S URV35 Level Meter
• #8005: Replace icons to text for ReportGenerator Test pass, fail or not-tested.
• #8035: Ability to use the R&S URV35 Powermeter by RS232
• #8039: Remove and replacing LLF from test data file 1 is also removing the LLF from another test data file in the EUT
• #8087: Driver: R&S ESW26 internal high-pass filters 2.4 and 5.6 GHz
• #8105: Powermeter virtual instruments keep disabling device specific settings after first measurement
• #8131: RadiMation memory leak when triggering powermeter
• #8183: Rohde & Schwarz, ESIB 26: Not all bytes are written to the GPIB-Board within the timeout period (GPIB: EABO)
• #8267: Burst Measurement does not show the combined graph data in the graph
• #8524: Incorrect mouse curser value shown in graph
• #8649: Missing error description Radisense10 Err 723
• #8659: Driver: Keysight N9914A Receiver spectrum analyser & powermeter
• #8660: Object reference error in the VI Powermeter window while measuring pulsed power using the RPR2006P
• #8707: Driver: BONN BSA 0140-200
• #8708: Driver: SCHAFFNER PCJ 9201B
• #8714: Driver: MOCS-MFD + OTM301
• #8716: RadiCentre justation, powermeter freezes
• #8747: R&S ESRP cannot be used in combination with 100 Hz RBW
• #8777: Driver: Switchmatrix: TOYO Corporation NS4900-series
• #8806: Amplifier ETS-Lindgren 8100-060
• #8808: Problems controlling the INNCO CO2000 controller when no Tilt mast is connected
• #8810: Frequency Range limited AC DC coupling
• #8826: Missing time-out / retry for Prana amplifier device driver
• #8827: Prana RFOff check
• #8838: Marconi 2024 Retry: Query Unterminated
• #8840: Amplifier stays in operate
• #8848: Wrong states PRANA MT400
• #8877: Count column is always shown in the event-log
• #8878: "Report Error" Error: Please fill in all the user information fields
• #8879: Driver: RadiAmp amplifiers
• #8883: Changing Engineer Value was either too large or too small for an Int32.
• #8886: Amplifier: Not all bytes are written to the GPIB-Board within the timeout period (GPIB: EABO).
• #8890: Unable to create new TSF for Radiated Immunity Substitution test
• #8891: Missing harmonics graphs
• #8897: An unknown error is raised, when the RadiCentre is not yet ready with initialization
• #8901: ESCI Scanning Receiver Option not available;DET1 CAV
• #8902: Dragging the marker of an emission graph: The method or operation is not implemented
• #8910: RPR3006W wrong command Mode 4
• #8912: Object reference clsIDocumentBase.UpdateAllViews update graph
• #8913: RepGen VDI test is not included in ||EUT|ALL IMMUNITY TESTS||
• #8914: CE MB infinit zoom peak loop
• #8919: Get amplifier information Object reference error
• #8923: ErrorReport dialog should show a red cross when not all the fields are filled in
• #8937: Manual controlled antenna tower doesn't show a message for the horizontal polarization at the begin of the test
• #8939: Driver: Configurable Turntable
• #8947: How to control a camera PTZ positioner using the configurable turntable device driver
• #8958: Add a required checkbox to the ErrorReport that the end-user agrees that his data is used
• #8964: Anritsu Command or parameter is not (correctly) confirmed and is probably raising an error. EMF
• #8982: Destination array was not long enough. Check destIndex and length, and the array's lower bounds
• #8985: HI6153 checkdevice passed while not connected
• #8990: Repeat count is not remembered in MB EFT TSF
• #8997: Y-axis of the multiband emission height graph is shown logarithmically to 100 m
• #9030: Dongle failure after installation of Windows 10 April 2018 Update
• #9034: Missing shortcut keycodes
• #9035: ||PEAK TABLE|| report generator code does not include peak number and frequency
• #9036: Before and After actions in testsite are showing strange DARE.RadiMat.clsCommand.... names
• #9038: Sunol SC99V antenna tower should by default use a small delay
• #9048: Driver: Amplifier NoiseKen NA80MF3G201003
• #9064: Show a clear error that the R&S rsnrpz_32.dll cannot be loaded
• #9073: Driver: R&S FSV3 tracking generator
• #9074: Unable to add TSF sub directory in Voltage Dips and Interrupts
• #9077: Surge Random angle on Thermo Scientific EMCPro is always 2 degrees
• #9080: RadiMation 2017.2.10 raises Error nr.: 536871935 on Windows 7 SP1
• #9091: Driver: Schwarzbeck 420NJ
• #9128: RadiField RFS2006B Error 574. Maximum number of retries reached on communication over the link.
• #9138: Driver: CHASE CBL8111
• #9143: Driver: Aaronia Hyperlog 7060
• #9149: Updated Radiwiki page for the Agilent U2000 series
• #9155: EMI radiated sweep very slow with test receiver R&S ESPI3
• #9162: Radimation - CAN-Bus link
• #9164: CISPR14 voltage probe transducer not added?
• #9174: Object reference not set to an instance of an object.
• #9183: Subject: LeCroy WaveSurfer Channel B: Binary block buffer couldn't be found
• #9191: ErrorReport: "LUMILOOP LS Probe 1.2 Y-axis (mode 0): Setting the 'Computer Interface Serial Number' raised an error. Is the identifier correct and present in the system? "
• #9198: Report: Template uses macro(AutoFitThisTable)
• #9223: Kalmus 757LC (Hi Band): Impossible to get description string for this Error! Probably an unknown Windows Error. Code: 236446416 (0x0E17E2D0)
• #9225: Software Protection Key could not be found on Windows 10 update
• #9235: Driver: Schloeder EMCL-20 & Schloeder EMCL-35
• #9255: Improve driver of R&S SME 06 to use High frequency accuracy