Release Notes/Solved items Version 5.7
Jump to navigation
Jump to search
RadiMation version 5.7.8[edit]
- #3830: Physical properties do not match with the units in the menus when using German language
- #3907: Angle and height of detected peaks are always the same (in singleband emission)
RadiMation version 5.7.7[edit]
- #3784: RI multiband test is not turning on the amplifiers in version 5.7.4 while this was working in version 5.6.13
RadiMation version 5.7.6[edit]
- #2775: Measurement of current by using the current sensor in combination with a multimeter or oscilloscope is wrong
- #3838: Why is it required to specify a magnetic flux density file for a MIL STD Calibration?
- #3839: Radiated Immunity MIL STD Calibration is always using a 70 dBuV Reference level
- #3853: CARAD monitor: settings for AD Input
- #3854: When cancelling CARAD timeout the "Save EUT As" window pops up
RadiMation version 5.7.5[edit]
- #3183: Crash of RadiMation Version 5.3.18 when CARAD driver is included
- #3614: Selecting no detector in the initial trace will result in a error 91 in multi band
- #3684: RadiMation and CAPL (CANalyzer 5.2.7)
- #3746: Peak zoom-in doesn't seem to work in multiband emission
- #3754: Climate chamber is not controlled correctly by RadiMation.
- #3820: graphs are smoother in version 5.7.5 than in version 5.5.7
RadiMation version 5.7.4[edit]
- #2597: In multiband immunity the cancel button only reacts on the end of the dwelltime
- #3546: Manual mode multiband emission test does not have an initial graph which results in a crash
- #3701: Multiband Radiated Emission: Default value in dropdown list for Turntable Angle specifies 235°
- #3720: During emission test: crosses instead of line
- #3736: I can not select apply modulation outside dwell time when selecting pulse
- #3753: HP4395A is always using 10 Hz RBW when it is used for a voltage measurement
RadiMation version 5.7.3[edit]
- #3386: the Radisense ctr1001B driver does not allow you to set the filter when using in gpib mode.
- #3674: UP300 - generator output
- #3704: Driver for RadiSense IV (RadiCentre) not working
- #3724: Radisense 4 over RS232 does not set the filter setting
- #3725: ESU 26 power meter driver is reporting unknown function during amplifier harmonics measurement
- #3726: Signal generator goes to +24 dbm while the limit is set to +10 dBm with a RI subst test
- #3729: CE multi band measurement is not showing the information below 1 MHz
RadiMation version 5.7.2[edit]
- #2204: Add a peak by clicking on the emission graph
- #2920: disable zoom in does not work directly
- #3073: Trace gaps on emission plots
- #3497: Keithley 2000 scanner does not detect connected device correctly
- #3502: RadiMation stays in a never ending loop to zoom the peak
- #3565: Negative turntable angles should be allowed in combination with the "measure during turn" option
- #3584: Wrong value readout of LeCroy 9361 scope
- #3628: Overloaded driver of the ESU is crashing then the device *IDN? description is not in capitals
- #3629: Changing the test order before reporting is crashing the RadiMation
- #3630: Driver: Maturo NCD
- #3634: Scaling in CE multiband is going to -1000 during the test.
- #3639: Driver: AH system SAS-570
- #3640: Driver: AH system SAS-571
- #3642: Driver: AH system SAS-550-1B
- #3643: Driver: AH system SAS-560
- #3649: Driver: HP 8673E
- #3650: Driver: HP 8662A
- #3654: Driver: IFI SMCC10
- #3655: Driver: OPHIR 5163
- #3657: Driver: HP 8341B
- #3658: Driver: Solar 6338-5-PJ-50N
- #3659: Driver: Solar 9233-50TS-50N
- #3661: Driver: Solar 7334-1
- #3662: Driver: Electro metrics EM-6892
- #3663: Driver: Electro metrics EM-6960
- #3664: Driver: Electro metrics EM-6961
- #3665: Driver: Electro metrics EM-6876
- #3668: Driver: Solar 9251-1
- #3673: Peak selection is not working as expected after deselecting all the peaks
- #3675: Configuration for optimize angle and height has problems with the measure- and observation time of different detectors
- #3676: During Optimize Height actual defined settings are not used but settings defined a step before
- #3677: When you press <<Detect Peaks>> after a radiated emission test in multiband you can not select more than one peak afterwards.
- #3678: Peak detected in first band but not in second band
- #3680: Configurable device signal generator device driver is not taking the correct codes in version 5.6.9
- #3682: Emission multiband is slow when 200 peak sweeps are used
- #3692: Prana amplifier does not turn off when the amplifier is changed during manual mode
RadiMation version 5.7.1[edit]
- #1948: No gridlines are shown from 1 GHz to 2 Ghz in logarithmic mode
- #2599: Order of tested bands should have a preference for the frequency order
- #2681: Editing a testlevel when multiple bands are selected, only changed the variable test-level for the first selected band
- #2754: Dongle is not detected when using Remote Desktop.
- #2756: Frequency Label of the x-axis of the graph in a correction file is displayed too low
- #2775: Measurement of current by using the current sensor in combination with a multimeter or oscilloscope is wrong
- #2866: How can scaling of frequency axis be configured when logarithmic scaling is choosen?
- #2911: dBmA/m unit in multi band is giving wrong measurement information
- #2999: Order of the bands in Multiband immunity is random
- #3141: Test equipment wrong in Sequence mode
- #3416: AM modulation indication on the HP 83630 is not activated
- #3454: Term MHz in Graph while the values are also in MHz.
- #3617: Driver: Anapico APSIN300HC
- #3621: No virtual multi meter available in version 5.7.0
- #3622: January and February dates are not detected on a non-english PC
- #3623: RI Magnetic calibration are not displayed after RadiMation is restarted
- #3625: New bands in a multiband test always have the color black
- #3626: Driver: R & S FSV 3
- #3627: Driver: R & S FSU 3
- #3632: Carrier level jumps directly from -100 dBm to +1 dBm when it should go up 1 dBm
RadiMation version 5.7.0[edit]
- #1937: Esi startup problem(s)
- #1986: Switching to the next band takes more then 2 minutes
- #2479: Driver: 1000W1000C
- #2557: FSP30 as power meter driver
- #3164: Cable correction between the signal generator and the amplifier is performed in the wrong direction
- #3494: ESU Time Domain Scan Fails when using lan
- #3551: R&S ESxx receivers: Perform short calibration before the final measurements
- #3560: R&S ESxx receivers: Enable demodulator
- #3568: SMR 20 does not support the external PM modulation
- #3569: strange behaviour after driver package update ESVS10
- #3575: Driver: Emco 3104C antenna
- #3576: Problems with deinitialization of ESVS10
- #3585: For a configurable LISN no manual mode is included
- #3586: CE multiband LISN test does not perform the band measurement
- #3587: driver for R&S SMC-B103
- #3588: The note on the multiband test window cannot be changed
- #3589: Note textbox on multiband tests, is not showing scrollbars
- #3590: Final peak measurement is performed too often
- #3591: Report generator is using more than 500 MB of memory
- #3617: Driver: Anapico APSIN300HC
- #3618: Driver: 30S1G4
- #3619: Driver: ETS EMCO 3142D
- #3620: Driver: Narda 6630