Spectrum Analyser: Difference between revisions
(New page: A spectrum analyzer is a piece of equipment that is used during EMC measurements. It's primary purpose is to measure the amplitude of individual frequencies that are contained in a RF sign...) |
No edit summary |
||
(5 intermediate revisions by 3 users not shown) | |||
Line 1: | Line 1: | ||
A spectrum | A spectrum analyser is a piece of equipment that is used during EMC measurements. It's primary purpose is to measure the amplitude of individual frequencies that are contained in a RF signal. This RF signal is very often an [[electromagnetic field]] that is received by an [[antenna]]. | ||
[[RadiMation]] has divided spectrum | [[RadiMation]] has divided spectrum analysers in three different classes: | ||
* Spectrum | * Spectrum analyser | ||
* Scanning receiver | * Scanning receiver | ||
* Receiver | * Receiver | ||
* FFT (Time-domain) analyser | |||
== Receiver == | == Receiver == | ||
Line 14: | Line 15: | ||
A scanning receiver is always measuring on all and the exact frequencies that are specified by the start-, stop- and step-frequency. | A scanning receiver is always measuring on all and the exact frequencies that are specified by the start-, stop- and step-frequency. | ||
== Spectrum | == Spectrum analyser == | ||
A spectrum | A spectrum analyser is a measuring device that sweeps in a short time along the frequency range that should be measured. During this sweep all frequencies are measured, and a PC can retrieve a list of the measured amplitudes from the spectrum analyser. The list of measured amplitudes is often a reduced list of a specific amount of frequencies (401 points, 601 points, etc...) | ||
== FFT analyser == | |||
An FFT analyzer is a device that processes signals in the time domain and transforms them into the frequency domain using the Fast Fourier Transform algorithm. Unlike a spectrum analyzer, which sweeps across a frequency range, an FFT analyzer captures a signal’s entire frequency content all at once, over a specified bandwidth. | |||
== Common == | == Common == | ||
Most scanning receivers and spectrum | Most scanning receivers and spectrum analysers include a lot of functionality to make it easier for an end-user to perform certain measurements. This additional functionality can be: | ||
* EMC Overview measurements | * EMC Overview measurements | ||
* Completely automated EMC measurements including peak detection and peak measurements | * Completely automated EMC measurements including peak detection and peak measurements | ||
* telecommunication measurements | * telecommunication measurements | ||
Spectrum | Spectrum analysers are always used during [[Emission]] tests. In some situations a spectrum analyser is also used during [[immunity]] tests, mainly to measure a RF signal. | ||
All the device drivers for spectrum | All the device drivers for spectrum analysers maintain the following information: | ||
* Allowed frequency range | * Allowed frequency range | ||
* if the device is a receiver / scanning receiver / spectrum | * if the device is a receiver / scanning receiver / spectrum analyser | ||
* Instructions on how to | * Instructions on how to | ||
** Set start-, stop-, center-, span- and step-frequency | ** Set start-, stop-, center-, span- and step-frequency | ||
Line 40: | Line 44: | ||
** change [[detector]] settings | ** change [[detector]] settings | ||
A complete [[:Category:Spectrum Analyser|list of all supported spectrum | A complete [[:Category:Spectrum Analyser|list of all supported spectrum analysers]] by [[RadiMation]] is available on this [[RadiWiki]] site. | ||
== Links == | == Links == | ||
* Wikipedia: [[wikipedia:Spectrum | * Wikipedia: [[wikipedia:Spectrum analyser|Spectrum analyser]] | ||
[[Category:RadiMation]] | [[Category:RadiMation]] |
Latest revision as of 14:30, 1 November 2024
A spectrum analyser is a piece of equipment that is used during EMC measurements. It's primary purpose is to measure the amplitude of individual frequencies that are contained in a RF signal. This RF signal is very often an electromagnetic field that is received by an antenna.
RadiMation has divided spectrum analysers in three different classes:
- Spectrum analyser
- Scanning receiver
- Receiver
- FFT (Time-domain) analyser
Receiver[edit]
A receiver is only measuring a single RF frequency. The receiver itself is not able to measure multiple frequencies. If more than one frequency need to be measured a PC has to change the selected frequency on the receiver, before a new measurement is performed.
Scanning receiver[edit]
A scanning receiver is a more intelligent receiver, which is able to step through a frequency range on it's own, so multiple frequencies can be measured automatically. A PC that is controlling the scanning receiver can instruct the scanning receiver to measure a certain frequency range. The scanning receiver will then return the data of the all the measured frequencies after (or during) the measurement is finished.
A scanning receiver is always measuring on all and the exact frequencies that are specified by the start-, stop- and step-frequency.
Spectrum analyser[edit]
A spectrum analyser is a measuring device that sweeps in a short time along the frequency range that should be measured. During this sweep all frequencies are measured, and a PC can retrieve a list of the measured amplitudes from the spectrum analyser. The list of measured amplitudes is often a reduced list of a specific amount of frequencies (401 points, 601 points, etc...)
FFT analyser[edit]
An FFT analyzer is a device that processes signals in the time domain and transforms them into the frequency domain using the Fast Fourier Transform algorithm. Unlike a spectrum analyzer, which sweeps across a frequency range, an FFT analyzer captures a signal’s entire frequency content all at once, over a specified bandwidth.
Common[edit]
Most scanning receivers and spectrum analysers include a lot of functionality to make it easier for an end-user to perform certain measurements. This additional functionality can be:
- EMC Overview measurements
- Completely automated EMC measurements including peak detection and peak measurements
- telecommunication measurements
Spectrum analysers are always used during Emission tests. In some situations a spectrum analyser is also used during immunity tests, mainly to measure a RF signal.
All the device drivers for spectrum analysers maintain the following information:
- Allowed frequency range
- if the device is a receiver / scanning receiver / spectrum analyser
- Instructions on how to
- Set start-, stop-, center-, span- and step-frequency
- change RBW settings
- change Reference level settings
- change Attenuation settings
- change VBW settings
- change preselector settings
- change preamplifier settings
- change measure time settings
- change sweep time settings
- change detector settings
A complete list of all supported spectrum analysers by RadiMation is available on this RadiWiki site.
Links[edit]
- Wikipedia: Spectrum analyser