Difference between revisions of "Configurable XYZ Positioner"
DevicesBot (talk | contribs) (Updated DeviceDriverInfo template) |
|||
(6 intermediate revisions by one other user not shown) | |||
Line 3: | Line 3: | ||
|DeviceDriverName=CONFIGXYZP | |DeviceDriverName=CONFIGXYZP | ||
|DeviceType=Configurable XYZ Positioner | |DeviceType=Configurable XYZ Positioner | ||
+ | |HideAutoData=1 | ||
|SupportedDeviceTypes=4194304 | |SupportedDeviceTypes=4194304 | ||
− | |||
}} | }} | ||
− | [[File: | + | ===Configurable XYZ Positioner=== |
+ | This driver can be configured to send commands to an EUT X, Y and Z-axis Positioner. It will be used in a Radiated Emission test with the location type GTEM configured. | ||
+ | Below an overview of the commands to configure: | ||
+ | |||
+ | [[File:Configurable_XYZ_Positioner.PNG]] | ||
+ | |||
+ | ====Initialisation and Check==== | ||
+ | {{ScreenElementDescription|Reset|The reset command sent during the initialisation phase}} | ||
+ | {{ScreenElementDescription|Init|The command sent during the initialisation phase}} | ||
+ | {{ScreenElementDescription|Get ID|The command sent to request the identifier of the device, e.g. *IDN?}} | ||
+ | {{ScreenElementDescription|Returned ID|The response of GET ID, this can either be the returned value or an regular expression}} | ||
+ | {{ScreenElementDescription|Deinit|The command sent during the de-initialisation phase}} | ||
+ | {{ScreenElementDescription|Wait for Completion after sending command|With this command the configured commands below will also send an *OPC? command to query if the operation is completed}} | ||
+ | |||
+ | ====XYZ Positioner==== | ||
+ | {{ScreenElementDescription|X Position|The command which will start to move the EUT in the X Position}} | ||
+ | {{ScreenElementDescription|X Position Stop|The command which will be sent after "X Position" command is sent and the configured waiting time is elapsed}} | ||
+ | {{ScreenElementDescription|Y Position|The command which will start to move the EUT in the Y Position}} | ||
+ | {{ScreenElementDescription|Y Position Stop|The command which will be sent after "Y Position" command is sent and the configured waiting time is elapsed}} | ||
+ | {{ScreenElementDescription|Z Position|The command which will start to move the EUT in the Z Position}} | ||
+ | {{ScreenElementDescription|Z Position Stop|The command which will be sent after "Z Position" command is sent and the configured waiting time is elapsed}} | ||
+ | {{ScreenElementDescription|Waiting time|The time to wait between the '...'-Position and '...'-Position Stop. Specified in milliseconds (ms). This waiting time is only used when the start command is configured.}} |
Latest revision as of 11:48, 11 February 2020
The Configurable XYZ Positioner device driver is a Positioner which is supported by RadiMation®.
Configurable XYZ Positioner
This driver can be configured to send commands to an EUT X, Y and Z-axis Positioner. It will be used in a Radiated Emission test with the location type GTEM configured. Below an overview of the commands to configure:
Initialisation and Check
Reset | The reset command sent during the initialisation phase |
Init | The command sent during the initialisation phase |
Get ID | The command sent to request the identifier of the device, e.g. *IDN? |
Returned ID | The response of GET ID, this can either be the returned value or an regular expression |
Deinit | The command sent during the de-initialisation phase |
Wait for Completion after sending command | With this command the configured commands below will also send an *OPC? command to query if the operation is completed |
XYZ Positioner
X Position | The command which will start to move the EUT in the X Position |
X Position Stop | The command which will be sent after "X Position" command is sent and the configured waiting time is elapsed |
Y Position | The command which will start to move the EUT in the Y Position |
Y Position Stop | The command which will be sent after "Y Position" command is sent and the configured waiting time is elapsed |
Z Position | The command which will start to move the EUT in the Z Position |
Z Position Stop | The command which will be sent after "Z Position" command is sent and the configured waiting time is elapsed |
Waiting time | The time to wait between the '...'-Position and '...'-Position Stop. Specified in milliseconds (ms). This waiting time is only used when the start command is configured. |