Talk:RadiMation Application Note 100: Difference between revisions

From RadiWiki
Jump to navigation Jump to search
No edit summary
No edit summary
 
(13 intermediate revisions by 4 users not shown)
Line 1: Line 1:
I do have some suggestions to further improve the application note:
MAHE: I have applied the requested changes
* The table of contents is shown twice
* Isn't it better to have a screenshot of the result in the introduction. It will make it clear how the result will be.
* The 'ScreenElement' macro can be used to indicate button names. I already modified it on a few locations. But not yet on all locations
* The 'Remove' button and the 'Custom Status window' checkbox are not explained.
* The section of 'Horizontal' or 'Vertical' doesn't show any text. Maybe it is better to provide a screenshot of the enhanced status window for each situation. Then the difference will be very clear...
* I Suggest to include a screenshot of an example after the 'List Of measurement parameters'.
* Then at the end of the document it is very helpful to show a screenshot during a test, where also the enhanced status window is shown
* In that last section it should also be explained that if the enhanced status window is closed, it can be shown again from the 'Window' menu.


[[User:Joro|Joro]] 10:01, 15 July 2015 (UTC)
 
I do have a few remarks for the improvements of this application note:
* The last screenshot: ([[:File:EnhancedWindowWithTest.png]]), shows an EUT window, a test and the Enhanced status window. The EUT Window is not relevant for the purpose of the screenshot, but it does cause that the screenshot is very wide. I think we should improve the screenshot to NOT show the EUT window.
* The values on all the screenshots that show the enhanced status window are very strange. They should be updated to show more logical values (maybe configure it in the KETC??):
** The last screenshot ([[:File:EnhancedWindowWithTest.png]]) shows: -200 dBm signal power (How is that possible??) while the field is expected to be almost 100 V/m. That is practically not possible. Also the frequency is just too low. At 280 kHz no 100 V/m can be generated.
** The horizontal screenshot shows a frequency of 1 Hz.
** The vertical screenshot shows a frequency of 1 Hz
 
 
 
== Review status ==
Applied review changes.        [[User:Mahe|Mahe]] ([[User talk:Mahe|talk]]) 09:45, 12 Februari 2019 (CET)
 
Did review. See remarks above.  [[User:Joro|Joro]] ([[User talk:Joro|talk]]) 09:39, 30 January 2019 (CET)
 
ROGE: Reviewed. [[User:Roge|Roge]] ([[User talk:Roge|talk]]) 15:45, 26 February 2019 (CET)

Latest revision as of 14:47, 26 February 2019

MAHE: I have applied the requested changes


I do have a few remarks for the improvements of this application note:

  • The last screenshot: (File:EnhancedWindowWithTest.png), shows an EUT window, a test and the Enhanced status window. The EUT Window is not relevant for the purpose of the screenshot, but it does cause that the screenshot is very wide. I think we should improve the screenshot to NOT show the EUT window.
  • The values on all the screenshots that show the enhanced status window are very strange. They should be updated to show more logical values (maybe configure it in the KETC??):
    • The last screenshot (File:EnhancedWindowWithTest.png) shows: -200 dBm signal power (How is that possible??) while the field is expected to be almost 100 V/m. That is practically not possible. Also the frequency is just too low. At 280 kHz no 100 V/m can be generated.
    • The horizontal screenshot shows a frequency of 1 Hz.
    • The vertical screenshot shows a frequency of 1 Hz


Review status[edit]

Applied review changes. Mahe (talk) 09:45, 12 Februari 2019 (CET)

Did review. See remarks above. Joro (talk) 09:39, 30 January 2019 (CET)

ROGE: Reviewed. Roge (talk) 15:45, 26 February 2019 (CET)

Power expressed in milliWatt in dB values.

  • 1 mW = 0 dBm
  • 2 mW = 3 dBm
  • 100 mW = 20 dBm
  • 1 W = 30 dBm
  • 100 W = 50 dBm
Retrieved from "https://wiki.radimation.com/wiki/index.php?title=Talk:RadiMation_Application_Note_100&oldid=18635"