Release Notes/Solved items Version 2015.3: Difference between revisions

Latest revision as of 07:53, 6 April 2016

RadiMation version 2015.3.6[edit]

#4575: Connecting another RadiPower Virtual instrument when another RadiPower is continuously measured, corrupts the data of the continuously measured RadiPower
#5455: Error wrong argument during Burst test
#5471: Burst measurement Unhandled exception Object reference not set to an instance of an object
#5876: App. Note 100: Enhanced Status Window usage and description included in the manual
#6095: Driver: Bonn Elektronik BTA 0122-3000
#6251: R&S ESR7 specific System Error: -222 Data out of Range DISP:TRAC:Y:RLEV:0.0103DBM
#6312: Timeout in communication with R&S ESPI after QP measurement
#6441: Frankonia FC is raising an -101 error during test initialization
#6473: Cannot access a disposed object frmVIPowerMeter
#6623: Driver: Frankonia ECU-3 / ECU-6
#6713: Driver Keysight 33521B Signal Generator
#6714: How can to get some specific trace data in the graph?
#6865: Implement retry of Software Update used for RadiField amplifier firmware updating
#6878: Comm failed with Powersensor PMM6630
#6888: Driver: Rohde & Schwarz ESR 26
#6890: Reportstatus of Kom ik hier? is shown during RPR3006W
#6898: EventLogData in list controll to be made possibly visible in RadiMation.
#6899: Event Window
#6913: EUT window is not correctly sized on 1024x768 beamer
#6939: Lasercode to activate the RadiSense fieldsensor laser inside the RadiCentre
#6942: Configurable AD-Convertor for asynchronous data
#6592: Update to .NET 4.6.1
#6954: Prana AP32DR312 amplifier serie is infinitely polling status when warnings are returned
#6962: Configurable AD Convertor device driver cannot interpret multiline result
#6965: Add ability to return the RAW AD Converter value

RadiMation version 2015.3.5[edit]

#2848: Regulated testlevel should be above requested testlevel if testlevel could not be regulated within the tolerance
#3962: A limit in a Multiband CI test is only checked when power is limited by amplifier limitation
#3963: Ramp method in CI Multiband doesn't remeasure the generated voltage
#4264: Field level is less than set
#5371: Initialization of Prana AP32 DR216 Amplifier is always successful
#5978: Driver: Prana DT70D Amplifier
#5988: Driver Teseq ITS6006 for IEC61000-4-3 & CISPR11 as Signal Generator
#6134: Driver: Teseq ITS6006 for IEC61000-4-3 & CISPR11 as Power meter
#6214: Driver: Prana DP600 amplifier
#6253: Driver: Prana DT70S amplifier
#6288: Driver: Prana UX55 amplifier
#6318: Driver: Prana SV70D amplfier
#6319: Prana LT320D amplifier doesn't work
#6358: RadiField and RadiGen doesn't switch to local at the end of a test
#6374: Driver: Prana MT700 amplifier
#6396: NI DAQ USB 6218 AD Converter read values are delayed
#6425: Driver R&S NRP-Z91 controlled by SMB100A using USB
#6460: Driver: Prana MT400 amplifier
#6489: Check if the HI-6005 fieldprobe is working correctly in combination with the EPI1001A
#6625: Driver: Frankonia EFS-10 / EFS-100
#6641: Driver: Control the polarization on the antenna using an RadiCentre external relais card
#6662: Virtual Instrument for the field strength sensor
#6712: Switch the external 40 dB attenuator used with Keysight 33521B
#6777: Amplifier Linearity / Uniformity test different result at 1 -6 GHz
#6787: Agilent 4403B Spectrum analyser Device Not Connected error
#6863: Explanation for the use of correction factors for a Current sensor
#6864: DVDRSYS.DLL cannot be loaded anymore from new device drivers
#6886: Driver: Bonn Elektronik BLMA 4060-40
#6901: How to create a correction factor using the unit of transfer impedance in dBOhm
#6909: Why is a window with a description and value text is shown during the test?

RadiMation version 2015.3.4[edit]

#1151: Minimum performance level fixed field
#1881: Graphs for applicable signal/forward/reflected/net power need to be added if a related input is measured
#1945: Generated Power in Multiband immunity is not limited by the allowed range that is configured the AD Channel
#2869: Multiband test does not allow the user to select only the reflected power meter as an input
#3605: Multiband minimum performance is not possible
#4090: RI multiband minimum performance not working
#4576: Auto ranging of the HI422 is not working correctly
#4821: Driver: Tektronix 3000 for fixed voltage test
#4873: Wrong reading of TDS 3054B scope
#5323: Pre measurement detector suddenly turns other detectors on or off
#5572: Use maximum performance level as new start level at next frequency
#5880: Button to show overview of Calibration Expired (activated) devices
#6125: Possibility to set the used type of average detector
#6163: Configurable AD converter measurement always returns zero
#6233: Control the oscilloscope Tektronix TDS 2000 Series by USB
#6268: Specify CW instead of NONE, if no modulation is applied
#6385: Add report generator keyword which only outputs the date
#6631: Driver Polarization of the RadiField
#6640: Driver Configurable antenna tower device driver to control polarization
#6712: Switch the external 40 dB attenuator used with Keysight 33521B
#6716: How to configure the increase of the power during regulation?
#6731: Allow that the available columns for the device driver can also be selected in the testsite configuration window
#6737: Driver RadiField 2003A/2006A/2003B/2006B
#6738: Windows 10 USB drivers for Radi-products
#6739: Hide the white area in the Virtual Instrument window
#6742: Agilent N9038A Average measurements taking longer than expected
#6762: Ability to select another detector in the R&S ESI powermeter
#6763: Using the R&S ESI 40 scanning receiver as a powermeter raises the error "BAND:MODE:FFT OFF"
#6764: Tektronix AFG 3252 Timeout while waiting for *OPC command
#6770: RadiField errors from the RadiCentre are not raised
#6771: RadiField Polarization driver should have 'ignore height change' ticked by default
#6774: R&S NRP-Z55 returns a -10000 dBm value when the powermeter returns a 'NaN'
#6779: How to perform a Radiated Immunity MB threshold level test
#6789: VSWR testlevel is not shown in the TestLevel inputs box
#6794: Multiple tests with same TSF name difficult to include in RG
#6801: Graph customization settings are not used during printout
#6806: A lot of 'Handles' are used by RadiMation
#6809: Can't find device driver for RadiField 1009B
#6812: Add new Reseller to the Sentinel Key program for Dongle programming
#6819: Tektronix TDS2024 is not correctly controlled
#6835: Can deleted measurements be recovered by RadiMation?
#6836: Is Windows 10 supported?
#6838: How to see more details of the tweeted improved RadiMation functionalities?
#6848: RPR3006W is not showing powermeter values when used as virtual instrument
#6858: RadiLog ReportError should include the RadiMation global event log of that process
#6867: Is it possible to add more than one amplifier to a test site?
#6881: Is the device driver for the R&S NRP-Z51 powermeter available?

RadiMation version 2015.3.3[edit]

#2550: Menu option that starts NI I/O Trace
#5091: Debugging of device drivers through DDLOGGER.DAT should be simplified
#5693: Driver: Agilent E7402A Spectrum Analyser
#6008: Possibility to temporarily disable system error checking in a device driver
#6119: Error that the frequency of an already used testsite is not suitable
#6384: How to use the R&S ESCI 7's built-in pre-amplifier in 30MHz-1Ghz range
#6400: Driver: IFI ST181-10 Amplifier
#6435: Is it possible to change a correction of an already performed MB emission test?
#6445: Keywords ||DATE MEASUREMENT|| and ||SETUP TYPE|| do not work anymore
#6447: Slow powermeter measurement of the R&S NRP Z91
#6533: PDF version of the RadiMation manual is 55 MB
#6551: Enables users to easily send Error Reports with RadiLog
#6553: Add RadiLog messages to the R&S NRPZ powermeter device driver
#6567: Include a menu entry in the main menu to start the RadiLog
#6597: R&S NRP-Z91 cannot be used in Powermeter Virtual Instrument
#6598: Checking a R&S NRP-Z91 takes forever when it is not connected
#6608: Add RadiLog messages to the USB HID device stream
#6653: Sending an error report causes an error report
#6655: Output parameters are not shown in RadiLog
#6658: Updating Error Report Window
#6659: Added button to ReportStauts error in RadiMation
#6666: Driver Teseq PMU 6006 powermeter
#6721: Not possible to measure the average field probe value during Multiband
#6722: RadiLog crashes with a 'startIndex cannot be larger than length of string'
#6778: More lines are included in the graph in a report than requested
#6784: “hot-key” to export the numbers from the harmonics + linear graph EUT-Calibration module
#6823: Do I need correction files in RadiMation for powermeters?

RadiMation version 2015.3.2[edit]

#1106: Directory names in the configuration should be shortened if they don't fit in the listview control
#2731: Address information of the customer, manufacturer and test-site should be able to be copied from or pasted to the clipboard
#2860: The amplifier control window is displaying nothing if no items are inserted
#4538: Turn during measurement explanation
#4805: Data export from menu REPORTS-EXPORT is not working
#5692: Driver: 3115 Double-Ridged Guide Antenna
#5877: Proceed to include some proposed wiki pages for inclusing in manual
#6071: Very slow band switching in Multiband Immunity (Levelling problem of Power Delivery Test)
#6277: The 'cancel' button should not be shown when an engineers is removed
#6283: Broadband units (like dBuV/m/MHz) are not possible for traces
#6438: Default frequency range of the EMCO / ETS-Lindgren antenna 3117
#6512: Use the Microsoft Visual Studio 2015 compiler
#6521: Amplifier Linearity test requires an antenna in the selected testsite for Conducted Immunity
#6546: New device drivers is raising Description for this error is not available error 536879923 during startup
#6548: Minimum supported Windows version should be changed to Windows 7 SP1
#6585: NRP Z55 zero operation took longer than 60 seconds error
#6588: RegisterDeviceDriver too slow. It takes a second.
#6605: Is the Ines USB-GPIB-2 card supported?
#6606: Is the Prologix GPIB convertor supported?
#6610: R&S ESRP 7: Not all bytes are written to the GPIB-Board
#6645: How can I set the resolution to logarithmic stepsize?

RadiMation version 2015.3.1[edit]

#3324: Linearity check for calibration (16 points, 5.1 dB down)
#4690: Language error: initialisation successfull <=> successful
#4772: Add a 'Pause' as a possible action
#5004: A warning should be shown if the AD-Channel maximum and minimum are the same
#5250: Change format of graph export per default
#5513: Directories configuration of latest version is interfering with older RadiMation version
#6168: Harmonic Graphlines have unlogical names
#6190: Add a general notification icon on all the Multiband configuration windows
#6193: Change the 'Change' button to 'edit' including a picture button.
#6196: The Version number in the shared Libs DLL's are not updated
#6197: Add a 'Remove' option in the right click menu of a device in the TestSite configuration window
#6201: The table with measurement data is not shown when the Harmonic test data is opened
#6242: Adding a 3rd amplifier to the amplifier control panel does not update the amplifier control panel correctly
#6292: Rename tabs on the testsite configuration: 'Standard 1' to 'Devices 1' and 'Standard 2' to 'Devices 2'
#6300: Enhanced Status Window parameters are not shown
#6326: Add more low baudrates: 1200, 600, 300, 50 Baud
#6335: 'Advanced Information' window should be renamed to 'General Information'
#6357: Regex returns 0 for notations with a space between +/- sign and the actuall number
#6401: Configurable Amplifier should have wait options after sending power on (for warming-up) and off (for cooling down)
#6408: Amplifier Slope verification for Conducted Immunity
#6455: Warnings related to wxEXPAND are shown when a wxWidgets dialog is shown

RadiMation version 2015.3.0[edit]

#5999: Mark the 'Continuous Measure' button in a different color when it is activated
#6295: When note window is opened the focus or cursor is not set to the text field by default
#6368: Duplicating more than 100 tests in a sequence takes a long time
#6369: Duplicating a test in a sequence file, doesn't mark the sequence file as changed
#6370: Radio buttons of Conducted Emission Manual Mode traces are swapped
#6387: It is not possible to select multiple peaks and therefore needs to select peaks one by one
#6388: Adding new peaks is resetting the peak lists selected column information

@@ Line 1: / Line 1: @@
+{{:Release Notes/Solved items Version 2015.3.6}}
+{{:Release Notes/Solved items Version 2015.3.5}}
+{{:Release Notes/Solved items Version 2015.3.4}}
 {{:Release Notes/Solved items Version 2015.3.3}}
 {{:Release Notes/Solved items Version 2015.3.2}}
 {{:Release Notes/Solved items Version 2015.3.1}}
 {{:Release Notes/Solved items Version 2015.3.0}}

Release Notes/Solved items Version 2015.3: Difference between revisions

Latest revision as of 07:53, 6 April 2016

Contents

RadiMation version 2015.3.6[edit]

RadiMation version 2015.3.5[edit]

RadiMation version 2015.3.4[edit]

RadiMation version 2015.3.3[edit]

RadiMation version 2015.3.2[edit]

RadiMation version 2015.3.1[edit]

RadiMation version 2015.3.0[edit]

Navigation menu

Release Notes/Solved items Version 2015.3: Difference between revisions

Latest revision as of 07:53, 6 April 2016

RadiMation version 2015.3.6[edit]

RadiMation version 2015.3.5[edit]

RadiMation version 2015.3.4[edit]

RadiMation version 2015.3.3[edit]

RadiMation version 2015.3.2[edit]

RadiMation version 2015.3.1[edit]

RadiMation version 2015.3.0[edit]

Navigation menu

Search