Configurable XYZ Positioner: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
DevicesBot (talk | contribs) (Updated DeviceDriverInfo template) |
||
| (5 intermediate revisions by one other user not shown) | |||
| Line 3: | Line 3: | ||
|DeviceDriverName=CONFIGXYZP | |DeviceDriverName=CONFIGXYZP | ||
|DeviceType=Configurable XYZ Positioner | |DeviceType=Configurable XYZ Positioner | ||
|HideAutoData=1 | |||
|SupportedDeviceTypes=4194304 | |SupportedDeviceTypes=4194304 | ||
}} | }} | ||
===Configurable XYZ Positioner=== | |||
This driver can be configured to send commands to an EUT X, Y and Z-axis Positioner. It will be used in a Radiated Emission test with the location type GTEM configured. | |||
Below an overview of the commands to configure: | |||
[[File:Configurable_XYZ_Positioner.PNG]] | [[File:Configurable_XYZ_Positioner.PNG]] | ||
====Initialisation and Check==== | |||
{{ScreenElementDescription|Reset|The reset command sent during the initialisation phase}} | |||
{{ScreenElementDescription|Init|The command sent during the initialisation phase}} | |||
{{ScreenElementDescription|Get ID|The command sent to request the identifier of the device, e.g. *IDN?}} | |||
{{ScreenElementDescription|Returned ID|The response of GET ID, this can either be the returned value or an regular expression}} | |||
{{ScreenElementDescription|Deinit|The command sent during the de-initialisation phase}} | |||
{{ScreenElementDescription|Wait for Completion after sending command|With this command the configured commands below will also send an *OPC? command to query if the operation is completed}} | |||
====XYZ Positioner==== | |||
{{ScreenElementDescription|X Position|The command which will start to move the EUT in the X Position}} | |||
{{ScreenElementDescription|X Position Stop|The command which will be sent after "X Position" command is sent and the configured waiting time is elapsed}} | |||
{{ScreenElementDescription|Y Position|The command which will start to move the EUT in the Y Position}} | |||
{{ScreenElementDescription|Y Position Stop|The command which will be sent after "Y Position" command is sent and the configured waiting time is elapsed}} | |||
{{ScreenElementDescription|Z Position|The command which will start to move the EUT in the Z Position}} | |||
{{ScreenElementDescription|Z Position Stop|The command which will be sent after "Z Position" command is sent and the configured waiting time is elapsed}} | |||
{{ScreenElementDescription|Waiting time|The time to wait between the '...'-Position and '...'-Position Stop. Specified in milliseconds (ms). This waiting time is only used when the start command is configured.}} | |||
Latest revision as of 11:48, 11 February 2020
The Configurable XYZ Positioner device driver is a Positioner which is supported by RadiMation®.
Configurable XYZ Positioner[edit]
This driver can be configured to send commands to an EUT X, Y and Z-axis Positioner. It will be used in a Radiated Emission test with the location type GTEM configured. Below an overview of the commands to configure:
Initialisation and Check[edit]
 Reset
|
The reset command sent during the initialisation phase |
| Init
|
The command sent during the initialisation phase |
| Get ID
|
The command sent to request the identifier of the device, e.g. *IDN? |
| Returned ID
|
The response of GET ID, this can either be the returned value or an regular expression |
| Deinit
|
The command sent during the de-initialisation phase |
| Wait for Completion after sending command
|
With this command the configured commands below will also send an *OPC? command to query if the operation is completed |
XYZ Positioner[edit]
| X Position
|
The command which will start to move the EUT in the X Position |
| X Position Stop
|
The command which will be sent after "X Position" command is sent and the configured waiting time is elapsed |
| Y Position
|
The command which will start to move the EUT in the Y Position |
| Y Position Stop
|
The command which will be sent after "Y Position" command is sent and the configured waiting time is elapsed |
| Z Position
|
The command which will start to move the EUT in the Z Position |
| Z Position Stop
|
The command which will be sent after "Z Position" command is sent and the configured waiting time is elapsed |
| Waiting time
|
The time to wait between the '...'-Position and '...'-Position Stop. Specified in milliseconds (ms). This waiting time is only used when the start command is configured. |