Release Notes/Solved items Version 2018.1.5
Jump to navigation
Jump to search
RadiMation version 2018.1.5[edit]
- #2338: Driver: R&S SWM with external modulation
- #5636: R&S ESPI 3 error Data out of range SCAN1:BAND:RES
- #8066: Extend the DSA832 pre-amp option detection
- #8113: Unable to communicate with CWS500N 1.2
- #8748: Use configurable driver for R&S UPV EUT monitoring
- #8514: Driver: emtest Compact NX
- #8521: Detection if the Keysight GPIB card is used is not working anymore with Keysight IO Libraries Suite 2018
- #8715: Rigol DSA 832: Specific System Error: -220, "Parameter error"
- #8796: Driver: Luthi CDN's 801-M1/M2/M3
- #9139: Driver: Denkovi DAE-CB/Ro16-JQC3FC-USB
- #9178: Unknow error - Change text when wiki can not find a page
- #9316: Software hangs in "detecting peak 100%
- #9438: Not all data from PMM9010 is received due to RS232 buffer overrun
- #9379: Graphline does not display (RBW 10 Hz)
- #9400: Driver: DARE!! Instruments DCN CDN's
- #9405: Report Generator changed font size in table causes errors
- #9416: Communication with R&S ESPI3
- #9423: Driver: R&S FPC1000
- #9455: Singleband frequency rounded
- #9457: Driver: Signal generator Aeroflex 2023
- #9463: No validation error is shown on the erroreport dialog in a new installation
- #9464: R&S SML signal generator should not use RSSML::msBuffer class member
- #9497: RPR2006C Wrong Command
- #9505: The red dashed 5.1 and 3.1 dB limit lines are not shown in the amplifier linearity test
- #9516: PMM9010: Incorrect start and-or stop frequency when 1 MHz RBW is used
- #9517: Keywords changed
- #9522: Amplifier Reflected power does not show 2018.1.4
- #9530: emtest PFS 500N: One or several values are limited by the simulator. The parameters are set to their minimum.
- #9537: Backport logging in clsGraphDrawer.Update to 2018.1.5
- #9543: Could not load file or assembly 'MindFusion.Common.WinForms'
- #9565: Radifield 2018 Error 1 on init. Wrong command
- #9573: Rigol Technologies DSA 815- Preamplifier option is not available in this device. Select no preamplification (0 dB)..log
- #9576: Destination array was not long enough
- #9578: GPIB Keysight USB GPIB 82357B Connection Expert 2018
- #9579: RadiSwitch Error
- #9581: RSS2010S
- #9589: Source array was not long enough. clsGraphElements.Add
- #9596: Report Generator table, generates multiple columns for 1 column name.
- #9598: Rigol DSA815: Unexpected RBW bandwidth
- #9606: Maturo Controller MCU N933 @7: Device stream is not connected.
- #9616: Not all spectrum analyser device drivers return the correct RBW mode during the GetRBW call
- #9622: "GAUSS INSTRUMENTS TDEMI X18: Insufficient location information or the device or resource is not present in the system. "
- #9642: EM Test NX 5:Change default port number to 1234
- #9643: Radimation crashes after error: Can not send/save the error report
- #9648: GAUSS INSTRUMENTS TDEMI X18: Specific System Error: 1
- #9649: Gauss Instruments TDEM X18: Ethernet not connected
- #9654: Driver: Receiver / Spectrum analyser Hewlett Packard 8591EM
- #9655: Driver: Signal generator - Marconi instruments 2023
- #9664: Agilent E8257D-567 (without ALC): Specific System Error: -221,"Settings conflict; Pulse period set less than pulse width value. Pulse width changed to match period value
- #9666: GAUSS INSTRUMENTS TDEMI X18: Specific System Error: -114,"Header Suffix Out of Range;SENS:SCAN1:TIME?"
- #9668: Source array was not long enough. Check srcIndex and length, and the array's lower bounds.
- #9672: Setting the BIAS Target of the RadiLink is not working
- #9675: Changing unit for Attenuation/Gain test does not work
- #9677: Unexpected power delivery test failed
- #9678: Power delivery test failed
- #9756: RBW switches from 120 kHz to Auto(1 MHz) during test with 2108.1.5 and R&S ESCI 7