Release Notes/Solved items Version 2018.1
Jump to navigation
Jump to search
RadiMation version 2018.1.5[edit]
- #2338: Driver: R&S SWM with external modulation
- #5636: R&S ESPI 3 error Data out of range SCAN1:BAND:RES
- #8066: Extend the DSA832 pre-amp option detection
- #8113: Unable to communicate with CWS500N 1.2
- #8748: Use configurable driver for R&S UPV EUT monitoring
- #8514: Driver: emtest Compact NX
- #8521: Detection if the Keysight GPIB card is used is not working anymore with Keysight IO Libraries Suite 2018
- #8715: Rigol DSA 832: Specific System Error: -220, "Parameter error"
- #8796: Driver: Luthi CDN's 801-M1/M2/M3
- #9139: Driver: Denkovi DAE-CB/Ro16-JQC3FC-USB
- #9178: Unknow error - Change text when wiki can not find a page
- #9316: Software hangs in "detecting peak 100%
- #9438: Not all data from PMM9010 is received due to RS232 buffer overrun
- #9379: Graphline does not display (RBW 10 Hz)
- #9400: Driver: DARE!! Instruments DCN CDN's
- #9405: Report Generator changed font size in table causes errors
- #9416: Communication with R&S ESPI3
- #9423: Driver: R&S FPC1000
- #9455: Singleband frequency rounded
- #9457: Driver: Signal generator Aeroflex 2023
- #9463: No validation error is shown on the erroreport dialog in a new installation
- #9464: R&S SML signal generator should not use RSSML::msBuffer class member
- #9497: RPR2006C Wrong Command
- #9505: The red dashed 5.1 and 3.1 dB limit lines are not shown in the amplifier linearity test
- #9516: PMM9010: Incorrect start and-or stop frequency when 1 MHz RBW is used
- #9517: Keywords changed
- #9522: Amplifier Reflected power does not show 2018.1.4
- #9530: emtest PFS 500N: One or several values are limited by the simulator. The parameters are set to their minimum.
- #9537: Backport logging in clsGraphDrawer.Update to 2018.1.5
- #9543: Could not load file or assembly 'MindFusion.Common.WinForms'
- #9565: Radifield 2018 Error 1 on init. Wrong command
- #9573: Rigol Technologies DSA 815- Preamplifier option is not available in this device. Select no preamplification (0 dB)..log
- #9576: Destination array was not long enough
- #9578: GPIB Keysight USB GPIB 82357B Connection Expert 2018
- #9579: RadiSwitch Error
- #9581: RSS2010S
- #9589: Source array was not long enough. clsGraphElements.Add
- #9596: Report Generator table, generates multiple columns for 1 column name.
- #9598: Rigol DSA815: Unexpected RBW bandwidth
- #9606: Maturo Controller MCU N933 @7: Device stream is not connected.
- #9616: Not all spectrum analyser device drivers return the correct RBW mode during the GetRBW call
- #9622: "GAUSS INSTRUMENTS TDEMI X18: Insufficient location information or the device or resource is not present in the system. "
- #9642: EM Test NX 5:Change default port number to 1234
- #9643: Radimation crashes after error: Can not send/save the error report
- #9648: GAUSS INSTRUMENTS TDEMI X18: Specific System Error: 1
- #9649: Gauss Instruments TDEM X18: Ethernet not connected
- #9654: Driver: Receiver / Spectrum analyser Hewlett Packard 8591EM
- #9655: Driver: Signal generator - Marconi instruments 2023
- #9664: Agilent E8257D-567 (without ALC): Specific System Error: -221,"Settings conflict; Pulse period set less than pulse width value. Pulse width changed to match period value
- #9666: GAUSS INSTRUMENTS TDEMI X18: Specific System Error: -114,"Header Suffix Out of Range;SENS:SCAN1:TIME?"
- #9668: Source array was not long enough. Check srcIndex and length, and the array's lower bounds.
- #9672: Setting the BIAS Target of the RadiLink is not working
- #9675: Changing unit for Attenuation/Gain test does not work
- #9677: Unexpected power delivery test failed
- #9678: Power delivery test failed
- #9756: RBW switches from 120 kHz to Auto(1 MHz) during test with 2108.1.5 and R&S ESCI 7
RadiMation version 2018.1.4[edit]
- #5261: Frequency plot can't be printed
- #5636: R&S ESPI 3 error Data out of range SCAN1:BAND:RES
- #5783: R&S ESU 26: Error -222: Data out of range. Depending on the preamplifier that is used
- #6373: R&S ESU 40: Error -222: Data out of range SCAN1:BAND:RES 1 KHZ
- #6811: Add new RadiMation startup Reseller logo
- #7329: Using multiple bands that switch preamplifier on and off gives error: R&S Receiver ESU 8
- #7482: RBW and SpanCentreFrequency order. Unable to set frequency multiband
- #7728: Unicode: clsFile EUT information is saved as ascii. Unicode characters are saved and read as '???'
- #8590: Unknown error when Visa is not installed, and is tried to control the EMCenter by LAN
- #8600: Spectrum Analyser frequency out of range with PreAmplifier MB
- #8691: Frequency out of range at second measurement.
- #8730: Source array was not long enough. Check srcIndex and length, and the array's lower bounds.
- #8734: controlling radigen over windows rs232 to com3 over usb is not working
- #9129: RadiMation crash when GPIB-Board is not installed or not configured correctly (GPIB-EDVR)
- #9177: Unable to open measurement files (_Object reference not set to an instance of an object..)
- #9188: Corrupt testfile, no data is visible in the graph
- #9221: Receiver (ID1691) Input 2: Specific System Error: -222,"Data out of range; SCAN1:BAND:RES 1 KHZ"
- #9247: Wrong output for Keyword ||DESCRIPTION||
- #9274: Driver: Field probe Narda EMC-30 RS232
- #9275: Driver: Passive drivers Philips Saeco S.p.A.
- #9277: Driver: Passive drivers CDVI Wireless S.p.A.
- #9278: MB test with Carad as eut controller gives an error
- #9287: Test data disappeared
- #9293: Radimation restarts during emission measurements (read/write outside the bounds of array)
- #9310: Testdata again not visible
- #9311: Test data lost / not visible
- #9314: No response turn table
- #9335: VI Window crash at closing
- #9338: Driver: Shaffner Broadband Horn Antenna 1-18 GHZ
- #9339: Driver: Stanford Research Systems - Model DS335
- #9341: Driver: Agilent N1913A
- #9345: De index ligt buiten de matrixgrenzen - Index out of range
- #9350: Signal power went too high (-6 dBm) during power delivery test
- #9363: Driver: CDN LAPLACE S46 ST8
- #9364: Driver: LISN LAPLACE (Cranage) LISN16A1P
- #9365: Driver: Antenna Laplace SA1020/RF200 No remote control
- #9366: Driver: Injection device Teseq KEMZ 801
- #9367: Driver: Calibration JIG Teseq KEMZ 801
- #9368: Driver: CDN MEB M3, M2, AF3-1 and AF2-1
- #9369: Driver: Antenna ARA LPB-2513
- #9382: Unable to ReportGenerate Emission and Peak Table
- #9394: Index was outside the bounds of the array.
- #9396: Index was outside the bounds
- #9398: Driver: Bonn BLMA 2060-30
- #9409: R&S ESI does not show graph of logarithmic stepped sweep
- #9426: Subject of ErrorReport should contain the description of the error
- #9428: Transmitting an ErrorReport is not working, complains that it is not possible to send ErrorReport
- #9440: Word locks documents after that it is not possible to print
- #9443: ErrorReport: "De bronmatrix is niet lang genoeg. Controleer srcIndex en de lengte ervan, en de ondergrenzen van de matrix. ".
- #9521: Peak table does not work in 2018 version
- #9524: Object reference not set to an instance of an object: clsCommandSetTurnTableAngle.IManualModeAsyncCommand_StartWork(
- #9525: Antenna Tower (ID1365) Aut.: Impossible to get description string for this Error! Probably an unknown RadiMation Error. Code: 805308669 (0x300008FD))
- #9538: Version Information is not displaying
- #9539: Text does not display on the devices tab in 2018.1.4
- #9549: Problem exporting conducted emission
- #9558: ErrorReport: "Access to the path 'C:\Users\u0058578a\Documents\My Music' is denied. "
- #9577: DARERSS2010I
- #9584: Question: What is AT. Is this used for low frequent rod or loop antenna?
- #9593: Vertical stripes QP measurements
- #9608: Unhandled exceptions
RadiMation version 2018.1.3[edit]
- #3570: Turntable Frankonia FC02 not working correctly
- #5984: Printing results of a burst test a second time, prints the same data as the first time
- #7219: Radifield powermeter is not usable on 800 MHz
- #7977: Holaday Instruments HI-4422: Invalid command
- #8014: Extend the maximum size of a generated Report
- #8031: Default graphs during Multiband Immunity are not shown during test
- #8162: Radimation startup crash Recursive customization file
- #8379: Object reference error in updating the Emission Graph.
- #8537: SMR40 total crash of communication
- #8585: Radiated Emission Magnetic field goes right into manual mode
- #8588: Field test level keyword missing.
- #8609: Agilent 34401 multimeter is always selecting DC coupling in CS101 calibration and CS101 test
- #8912: Object reference clsIDocumentBase.UpdateAllViews update graph
- #9112: No match was found in the specified regular expression
- #9116: Fax number on about screen is not valid anymore
- #9119: Sharing Monitoring AD channels between tests, and test setups.
- #9141: Radimation crashes, no error report
- #9173: MXE ERROR -224: Settings conflict; only active antenna unit available; no other y axis units
- #9181: File > New > EUT is showing a strange filename
- #9195: RF Amplifier (ID1647); Device not connected
- #9253: Add the name and identifier of the Reseller as it is programmed in the dongle in the ErrorReport
- #9254: Add the identifier of the dongle in the ErrorReport
- #9263: Unhandled exception handler is crashing software before report can be transmitted
- #9271: Radimation stops: software tries to change RBW on R&S ESU 8
- #9272: RadiMation keeps waiting: RBW value changed by R&S ESU 8
- #9282: Problem using the EMS RSC controller
- #9283: Cannot Find the device driver (RPR2006P)
- #9285: R&S ESU 8 Input 2 Scanning Receiver: Specific System Error: -200,"Execution error;Function not available;ABORT"
- #9302: BLMA 1040-100D
- #9306: Incorrect table export of polar plot
- #9307: No match was found in the specified regular expression
- #9309: ErrorReport: "Rohde & Schwarz ESR 7 Input 1 Scanning Receiver: Specific System Error: -200,"Execution error; Function not available; ABORT""
- #9343: Driver for: Teseq CBA 16-150
- #9347: ErrorReport: "Fixed power test. Vrijdag Einde vd dag
- #9351: ReportError("Exception has been thrown by the target of an invocation.")
- #9352: Cannot install CTR 1001S in win 10
- #9370: ErrorReport: "Cannot find the device driver.
- #9509: Install issues due to download problems
- #9534: Decimal sign changes after radimation error
- #9546: Signal power went too high (-4 dBm) during power delivery test
- #9550: Keywords not woking in Radimation_Validation_Template v 4.2
- #9553: EN61000-4-6 Callibration and testing with two powermeters
- #9557: Rohde & Schwarz ESPI 3: Specific System Error: -200,"Execution error; Function not available; CALC:UNIT:POW DBUV
- #9560: ErrorReport: "File 'J:\postvak\testsite\Referentie metingen\Radiated Immunity Semi Anechoic Chamber EN61000-4-3\ID1494 - Cavendish\RI 80-1000MHz 10Vm AVG 2ndQ 2011.BMP' not found during a 'ShellExecute' call "
- #9588: Missing/empty cells in peak table
- #9594: Error .csv dump LeCroy Wavesurfer
- #9660: TSF file name changed.
- #9667: Not able to connect to devices in RadiCentre
RadiMation version 2018.1.2[edit]
- #4209: No frequency verification on correction file
- #8718: HP3478A Multimeter wrong mode selection.
- #8986: No graphline is shown anymore in the polar plot of a peak
- #9136: Driver: HP 85420E Pre-amplifier
- #9145: Driver: Aaronia antennas
- #9245: DARE!! Instruments RPR2006C--FWD: No match was found in the specified regular expression.
- #9270: Using R&S Z91 as monitoring power sensor with attenuation (-30 dB) takes a long time to measure
- #9403: RI: Certain graph lines are not added to the report. Outputing a table does work.
- #9663: Radisense 10 RSS2010B/H cor. OFF: I2C Not-Acknowledge (NACK) "
RadiMation version 2018.1.1[edit]
- #8567: Include Sentinel System Driver 7.6.0 in setup program
- #8720: Power is sometimes regulated below the desired testlevel of 1 watt
- #8773: Configurable RS232 stream always appends \n after command
- #8865: PDF icon for the manual on the desktop is always using a white icon. Not showing the PDF icon