The Configurable Signal Generator device driver is a Signal Generator which is supported by RadiMation®.
Configuration
The following tabs are available in the advanced configuration of the Configurable Signal Generator:
The frequency range of the Configurable Signal Generator as provided by the manufacturer is shown and selected as default. It is possible to overrule these frequencies and to manual adjust the allowed frequency range of the Configurable Signal Generator.
 Use default start frequency
|
If the checkbox is checked, the default start frequency will be used as the lowest usable frequency in a test for this device.
|
| Custom start frequency
|
If the Use default start frequency checkbox is unchecked, another start frequency (expressed in MHz) can be specified. The customized start frequency will then be used as the lowest usable frequency in a test for this device. The customized frequency can be a limitation or an extension of the default start frequency.
|
| Use default stop frequency
|
If the checkbox is checked, the default stop frequency will be used as the highest usable frequency in a test for this device.
|
| Custom stop frequency
|
If the Use default stop frequency checkbox is unchecked, another stop frequency (expressed in MHz) can be specified. The customized stop frequency will then be used as the highest usable frequency in a test for this device. The customized frequency can be a limitation or an extension of the default stop frequency.
|
Specifying a different frequency range can be useful if for example:
- A device (like a coupler, antenna, injection device, cable, etc...) is still useable (but out of specification) outside the standard suggested frequency range.
- An external mixer is used to measure an extended frequency range.
- An up- or down-convertor is used to shift the frequency range.
- A newer model of a device is present that has an extended frequency range, and still uses the same remote control commands.
Be careful changing these setting as RadiMation® is no longer able to verify if the Configurable Signal Generator is used outside frequency range that is specified by the manufacturer. This may result to serious damage of your measurement device.
| Start
|
The start frequency of the operational band of the signal generator in MHz.
|
| Stop
|
The stop frequency of the operational band of the signal generator in MHz.
|
| Reset
|
The reset code that needs to be send to device. When left blank no command will be send.
|
| Init
|
The Init code that needs to be send to device. When left blank no command will be send.
|
| Get Id
|
The code that needs to be send to device to get the identification back. A common used SCPI command is *IDN?. When left blank no command will be send.
|
| Returned ID
|
The code that is send back as a return on the Get ID code. When left blank, no check will be performed.
|
| Set Frequency
|
The set frequency code that needs to be send to device. When left blank no command will be send.
|
| Set Carrier
|
The set carrier code that needs to be send to device. When left blank no command will be send.
|
| Carrier On
|
The carrier on code that needs to be send to device. When left blank no command will be send.
|
| Carrier Off
|
The carrier off code that needs to be send to device. When left blank no command will be send.
|
| Communication
|
Opens the dialog in which the communication method to connect to the amplifier can be selected and configured.
|
AM
| AM On
|
The AM on code that needs to be send to device. When left blank no command will be send.
|
| AM Off
|
The AM off code that needs to be send to device. When left blank no command will be send.
|
| Sine Wave
|
The modulator sine wave code that needs to be send to device. When left blank no command will be send.
|
| Square Wave
|
The modulator square wave code that needs to be send to device. When left blank no command will be send.
|
External AM
| External On
|
The external AM on code that needs to be send to device. When left blank no command will be send.
|
| External Off
|
The external AM off code that needs to be send to device. When left blank no command will be send.
|
FM
| FM On
|
The FM on code that needs to be send to device. When left blank no command will be send.
|
| FM Off
|
The FM off code that needs to be send to device. When left blank no command will be send.
|
| Sine Wave
|
The modulator sine wave code that needs to be send to device. When left blank no command will be send.
|
| Square Wave
|
The modulator square wave code that needs to be send to device. When left blank no command will be send.
|
External FM
| External On
|
The external FM on code that needs to be send to device. When left blank no command will be send.
|
| External Off
|
The external FM off code that needs to be send to device. When left blank no command will be send.
|
PM
| Pulse On
|
The pulse on code that needs to be send to device. When left blank no command will be send.
|
| Pulse Off
|
The pulse off code that needs to be send to device. When left blank no command will be send.
|
External PM
| External On
|
The external PM on code that needs to be send to device. When left blank no command will be send.
|
| External Off
|
The external PM off code that needs to be send to device. When left blank no command will be send.
|
