Difference between revisions of "IEC 61000-4-19"
| (7 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| + | __NOTOC__ | ||
The [[EN]]/[[IEC]] 61000-4-19 standard describes how [[Conducted Immunity]] measurements are performed on A.C. power ports in the frequency range from 2 kHz to 150 kHz. | The [[EN]]/[[IEC]] 61000-4-19 standard describes how [[Conducted Immunity]] measurements are performed on A.C. power ports in the frequency range from 2 kHz to 150 kHz. | ||
| − | The title of this standard is | + | |
| + | The exact title of this standard is: "IEC 61000-4-19: Electromagnetic Compatibility (EMC) - Part 4-19: Testing and measurement techniques - | ||
Test for immunity to conducted, differential mode disturbances and signalling in the | Test for immunity to conducted, differential mode disturbances and signalling in the | ||
frequency range from 2 kHz to 150 kHz, at a.c. power ports" | frequency range from 2 kHz to 150 kHz, at a.c. power ports" | ||
| Line 23: | Line 25: | ||
This test should be performed 4 times, where each test is using pulse modulated (with a 50% duty cycle) CW signal. | This test should be performed 4 times, where each test is using pulse modulated (with a 50% duty cycle) CW signal. | ||
Depending on the AC Mains frequency the pulse modulation frequencies should be: | Depending on the AC Mains frequency the pulse modulation frequencies should be: | ||
| − | {| | + | {|class="wikitable" |
!AC Mains frequency | !AC Mains frequency | ||
!Pulse modulation frequencies | !Pulse modulation frequencies | ||
| Line 35: | Line 37: | ||
== Related standards == | == Related standards == | ||
| − | * [[ | + | * [[IEC 61000-4-13]] |
| − | * [[ | + | * [[IEC 61000-4-16]] |
== Links == | == Links == | ||
| − | * | + | * [https://webstore.iec.ch/publication/4188 IEC 61000-4-19] |
| − | |||
[[Category:Standard]] | [[Category:Standard]] | ||
Latest revision as of 09:00, 19 December 2022
The EN/IEC 61000-4-19 standard describes how Conducted Immunity measurements are performed on A.C. power ports in the frequency range from 2 kHz to 150 kHz.
The exact title of this standard is: "IEC 61000-4-19: Electromagnetic Compatibility (EMC) - Part 4-19: Testing and measurement techniques - Test for immunity to conducted, differential mode disturbances and signalling in the frequency range from 2 kHz to 150 kHz, at a.c. power ports"
Relevant products:
- All equipment operating at a mains supply voltage up to 280 V and a frequency of 50 Hz or 60 Hz.
The IEC 61000-4-19 describes two different (modulation) test-types which are recommended to use both:
- a sweep test performed with CW pulses with pauses between each pulse
- a test performed with blocks of rectangularly modulated pulses with four different modulation frequencies
sweep test with CW pulses with pauses
- A standard Conducted Immunity test should be performed, using a dwelltime of at least 3 seconds
- Between each tested CW frequency, the level of the test signal is zero for a period of 300 ms (with a tolerance of +- 200 ms). This creates a 'Pulsed CW test with pauses'.
- A 2% frequency step will be used to step from 2 kHz to 150 kHz.
sweep test with rectangularly modulated pulses
- A standard Conducted Immunity test should be performed, using a dwelltime of 3 seconds.
- A 2% frequency step will be used to step from 2 kHz to 150 kHz.
- Between each tested CW frequency, the level of the test signal is zero for a period of 300 ms (with a tolerance of +- 200 ms).
This test should be performed 4 times, where each test is using pulse modulated (with a 50% duty cycle) CW signal. Depending on the AC Mains frequency the pulse modulation frequencies should be:
| AC Mains frequency | Pulse modulation frequencies |
|---|---|
| 50 Hz | 3 Hz, 101 Hz, 301 Hz, 601 Hz |
| 60 Hz | 4 Hz, 121 Hz, 361 Hz, 721 Hz |
