Difference between revisions of "RadiMation Application Note 128"

From RadiWiki
Jump to: navigation, search
(Created page with "= Making a custom emission table with the report generator = In this application note we explain how you can use the report generator to generate a custom emission table with...")
 
Line 1: Line 1:
−
= Making a custom emission table with the report generator =
+
= Reading the output value of single antenna's separately of a isotropic probe =
−
In this application note we explain how you can use the report generator to generate a custom emission table with the values that you need.
+
In this application note we explain how you can output the individual value's of the antenna's of a isotropic probe.
  
 
== Overview ==
 
== Overview ==
  
−
This application note is a addition to the manual.
+
RadiMation usually displays the iso-tropic value of a probe. In some cases it is also possible to read the output of the individual antenna's.
  
−
Please read: [https://wiki.dare.nl/wiki/index.php/Chapter_13#Inserting_the_Peak_Limit_into_the_table_(example) Inserting the peak limit to the table]
+
If the hardware supports it, Radimation can be set up to read these individual values. In this document we will show how to set this up.
  
−
When you do a Radiated test in Radimation you get a peak table which shows the peaks found and the different columns of information. This information is dynamic and based on the test settings.
 
−
Eg. you will not see avg column when you are not using that trace.
 
  
−
This can make it a bit confusing when you need to make a table. In this application note we explain how to find the values and explain some best practices.
+
=== Set up in RadiMation ===
−
In the picture below the emission table is displayed. All the values that you see here can be retrieved by the report generator from that document.
 
  
−
[[File:127-EmissionTable.png]]
+
To set this up in Radimation you need to create a separate driver per antenna. You can do this by going to:
  
−
Be aware that not always all columns are displayed. This can be selected by using the column chooser. The column chooser can be used to add columns. Use remove column to remove a column. Once removed it can be chosen again via the column chooser.
+
Configuration -> Configuration -> Device Drivers
 +
Go to Field Sensors
 +
Add a driver for your field probe (We use a RSS2010I here, keep in mind this is also possible with other models. Check in the driver's advanced page if you see a setting for the Direction)
  
−
It is important to understand that not all values are visible. When you use the report generator and build a custom table you need to know what is exactly in the table as you need the exact column names to retrieve them.  
+
Rename it and add the name of the axis.
  
−
[[File:127-ColumnChooser.png]]
 
  
  
−
===Displaying the table in Excel ===
 
−
 
−
To see what you can retrieve from the table you need to know what the output is of the table. The best practice to do this is to export the table to excel. We use excel because it is easy to display large tables.
 
−
 
−
Make a excel file. In the first cell place the following code:
 
−
 
−
||SELECT ALL FROM PEAK TABLE||
 
−
 
−
This will then result in a table looking something like this (The result can be different as it is dependent of the settings used):
 
−
 
−
[[File:TableExcel.png]]
 
−
 
−
Now you have output the whole table. Now you can see all the data that you can retrieve from the testfile. This helps to see what you can retrieve wit the report generator and to know what the column names are.
 
−
 
−
Look for the columns you want to add and write down the column names used.
 
  
 
===Using the data from the excel table output===
 
===Using the data from the excel table output===

Revision as of 13:15, 6 January 2020

Reading the output value of single antenna's separately of a isotropic probe

In this application note we explain how you can output the individual value's of the antenna's of a isotropic probe.

Overview

RadiMation usually displays the iso-tropic value of a probe. In some cases it is also possible to read the output of the individual antenna's.

If the hardware supports it, Radimation can be set up to read these individual values. In this document we will show how to set this up.


Set up in RadiMation

To set this up in Radimation you need to create a separate driver per antenna. You can do this by going to:

Configuration -> Configuration -> Device Drivers Go to Field Sensors Add a driver for your field probe (We use a RSS2010I here, keep in mind this is also possible with other models. Check in the driver's advanced page if you see a setting for the Direction)

Rename it and add the name of the axis.



Using the data from the excel table output

Now that you know the columns you want to retrieve and their names you can build your select statement:

SELECT [Peak Number], Frequency, RBW, Peak, Peak Limit, Status FROM PEAK TABLE

Any of the column names that you have can be added to the select statement to build your custom table.

Below we are adding the Peak Limit to the table.

SELECT [Peak Number], Frequency, RBW, Peak, [Peak Difference], Peak Limit, Status FROM PEAK TABLE


Pointers

As the report is depended from the columns in the test it is best to first build your test exactly as you want before starting to make the report. This is because when you have build the test and it is final then you know for certain that you have all the data to generate the reports you need.

Retrieved from "https://wiki.radimation.com/wiki/index.php?title=RadiMation_Application_Note_128&oldid=19606"