Release Notes/Solved items Version 2014.2

RadiMation version 2014.2.12

• #4238: Error field probe by polariser
• #4900: Amplifier Information Could not be found error
• #5237: Correction is applied when no correction file is attached
• #5844: Advantest analyser as powermeter is not automatically switching the attenuator
• #5845: Using Rigol as powermeter can cause large measurement errors
• #5866: High Peak and overshoot measurements with PMM9010F and PMM 9030
• #5884: R&S ESU 26 Input 2 is using input 1
• #5909: Configuration of Narrow band / broad band detection according to standards has disappeared
• #5911: Device Not connected errors for AR amplifier 75A400

RadiMation version 2014.2.11

• #4041: Antenna mast Frankonia FC 02 not working
• #5597: Driver PMM Switching control Box
• #5733: When should I use the Forward Power Mode and when the Net Power Mode?
• #5893: How to perform a continuous measurement mode with continuously sweeping during turning?
• #5908: Continuous measurement mode is not working for the Sunol SC104V Turntable

RadiMation version 2014.2.10

• #2824: Up down control of Carrier level control in manual mode test, is always going upwards
• #2825: Multiband immunity test with a signal generator output correction does not regulate correctly
• #3572: Prana AP32MT255 command set has changed after upgrade.
• #5633: Equipment keywords are not replaced and 'found new code' Receiver
• #5875: Infinity regulation of carrier level started at 120011 dBm

RadiMation version 2014.2.9

• #4684: AR 150W1000 in remote is not working correctly
• #4707: Conventional Antenna and Turntable settings
• #4727: Data export methods are exporting in a different way
• #5322: Signal Generator setting the frequency raised an error
• #5580: Description of Optimize Height and optimize Angle functionality is missing
• #5808: Driver Amplifier Research 1000A225 amplifier
• #5835: General issues with the R&S ESRP
• #5844: Advantest analyser as powermeter is not automatically switching the attenuator
• #5861: Not possible to remote control Milmega AS0102-100 and AS1860-100 amplifier
• #5861: Not possible to remote control Milmega AS0102-100 and AS1860-100 amplifier
• #5871: Metrohm Antenna Tower device driver
• #5873: Power delivery test fails
• #5874: Driver PMM EP408 electrical field probe
• #5881: Radimation doesn't detect the Software Protection Dongle/key

RadiMation version 2014.2.8

• #4639: Cancel button Multiband is Pause button
• #4959: Remote controlling Maturo NCD over LAN
• #5215: R&S ESU8 - EMI error Not all bytes are written to the GPIB-board within the timeout period
• #5542: R&S BBA100 RF Amplifier has no RF Path selected
• #5709: Unknown Device type errors Switch matrixes Radicentre CTR 1008A raises Device Not Connected errors
• #5735: R&S ESU: Query interrupted error
• #5774: Antenna tower reports the error: Field probe is still busy with zeroing the field probe
• #5804: Error message when downloading and starting 2014.2.8
• #5806: RPR connection is lost and can't be restored
• #5817: Not all bytes are written with Sunol SC99V controller
• #5820: Very low forward power during CDN calibration
• #5822: Unexplainable 20dB offset of CE measurement results
• #5833: Object error during startup splash screen crashes RadiMation
• #5834: Error access to the path (..) is denied
• #5865: How to configure the PMM 9030 User Controlled LISN?
• #5867: Expected automated measurement in Multiband when manual mode test window appears
• #5869: How to configre a ISO11452-2 Radiated Immunity (with Radar Pulse) test?
• #5870: Driver Sunol controller SC110V

RadiMation version 2014.2.7

• #4959: Remote controlling Maturo NCD over LAN
• #5557: Reading out dBr values with Audio Analyser UP 300
• #5650: Driver Rigol DSA815 and Rigol DSA1030 series
• #5656: Configurable Amplifier and Coupler doesn't retain frequency range
• #5664: N9038A error -410 Query interrupted
• #5688: Check on software software protection key fails
• #5702: HP8591E EABO errors can abort a running test
• #5703: How to customize and adjust the markers in RadiMation?
• #5706: R&S FSH (for field probe) is not using transducer list
• #5710: R&S ESU8 EMI error -200 Function GAIN:STAT OFF not available
• #5711: R&S FSV 13 error -113 Undefined header INP:ATT:PROT ON
• #5719: Amplifier AR 75A400 device not connected error
• #5721: Driver: PMM 7010
• #5725: Driver Emco 7123 field sensor
• #5731: Driver Agilent U2001A Power meter
• #5732: Possible stopping an immunity measurement automatically?
• #5736: No trace data obtained from measurements with FSV13
• #5746: Driver RadiField Amplifier
• #5747: Driver RadiField Forward and Reflected power meter
• #5748: Driver RadiField Coupler
• #5749: Driver RadiField Antenna
• #5764: Driver RadiPol
• #5766: RadiMate 3 RAW communication issues
• #5772: Device Driver Function Function Not Implemented error for Rigol spectrum analyser as powermeter
• #5773: Amplifier that is already in OPERATE can result in an endless test initialization

RadiMation version 2014.2.6

• #1742: Auto attenuation can result in false measurements, QP is going higher than PK
• #2510: Remeasurement of peaks should be possible to do with different testequipment than prescan
• #3294: R&S ESIB 26 Timeout while waiting for *OPC command
• #4195: Crash at the end of an immunity test
• #4219: Amplifier IFI SMC 100 error Not all bytes are written on GPIB
• #4230: Driver: IFI SMC 100 amplifier
• #4790: R&S Spectrum analyser FSH6 does not work
• #4984: Driver Agilent 33621A and 33622A
• #5075: Rename R&S NRT Channel 1 & 2 device driver to R&S NRT
• #5280: LISN default frequency range settings is not disabled
• #5335: Can't connected with R&S NRP Z91 power meter
• #5577: AR10W1000C communication issue
• #5653: How to install the R&S NRP-Z91
• #5654: Agilent N5183-520 error -222,"Data out of range; value clipped to upper limit."
• #5668: GPIB Primary Address settings is blown up
• #5669: Table information is not automatically resized
• #5681: Driver: Amplifier Research 15S1G6
• #5690: Update N5183 device driver series names
• #5720: Maximum field on this frequency warnings, field is zero, amplifier protection errors etc.
• #5722: Radimation default password (Radimation) is not accepted during the login

RadiMation version 2014.2.5

• #5052: Reference level is changed during measurement, generating an IF overload
• #5121: Cannot access the file because it is being used by another process
• #5126: Peak values ​​are far below the Quasi peak values
• #5278: Driver AD Agilent 53220A (Frequency Counter)
• #5284: Slow measurement, when ESU8 used as powermeter and Att on auto
• #5377: LLF style and color settings are not retained
• #5417: Detected overload R&S ESIB is ignored during test
• #5445: How to configure measurement with Schwarzbeck HXYZ 9170 Triple Loop Antenna
• #5487: Driver Agilent AD Converter 34972 for multiple measurements
• #5578: Optimize height and angle are not using the correct measurement results
• #5606: Optimize height and optimize angle settings are not retained
• #5617: AR 250W1000B can't be controlled by ethernet
• #5631: Could not find file C:\ADVANCED.DAT
• #5635: Driver R&S FSH 3 as readout unit for field probe
• #5638: Error AR FM50040 field probe not connected or not activated
• #5643: Graphlines will become invisible after opening other test results
• #5644: R&S BBA100 RF Amplifier timeout and command not possible errors
• #5648: Peak table keywords for (SQL queries) are not available for the enduser
• #5649: Generating a WORD.DOCX report using a WORD.DOCM template causes a runtime error
• #5651: The report generator should show a clearer message if the report cannot be opened
• #5652: Repetition interval data of a detected peak is lost when an angle optimization is performed
• #5654: Agilent N5183-520 error -222,"Data out of range; value clipped to upper limit."
• #5655: Used observation time for the final measurement is too short if first measurement takes a long time
• #5657: 25A250AM2 doesn't switch off after measurement
• #5658: Should we insert an Absorbing clamp?
• #5659: Why does the expected forward power value differs?
• #5660: Enable the Repetition Interval determination by default
• #5784: R&S ESU: Not all bytes are written error

RadiMation version 2014.2.4

• #5358: Peak numbering between graph and table are not corresponding
• #5542: R&S BBA100 RF Amplifier has no RF Path selected
• #5599: Changing between communication streams reset the saved user settings
• #5601: Timeout with Gauss TDEMI receiver
• #5603: Strange measurements with LeCroy wavesurfer 64Xs
• #5610: Path configuration seems to be lost
• #5613: Timeout error with R&S ESI 40 as powermeter
• #5628: No match was found in the regex with Chauvin Arnoux 43 probe

RadiMation version 2014.2.3

• #4806: R&S Spectrum analyser FSH6 not connected
• #5035: Improve how customers can download new RadiMation version
• #5189: Sweeptime is used during final measurement instead of the QP measurement time
• #5205: CTR unknown device type error with RGN
• #5381: Bonn BLMA 0832-270D can't control the ON/OFF of band 2
• #5500: How to get certain columns and rows of a peak table in to the report
• #5539: Explain Traces detectors and Narrow Broadband discrimination
• #5566: LAN control of the R&S ESPI Controlled LISN
• #5583: TSF Turntable settings are not retained
• #5585: Editing the device driver from the Calibration expire window always opens the first in the list
• #5586: Information is not visible with current printout templates
• #5588: Selection of the graph lines in the Graph customization is not working
• #5619: Unexpected results of exported graph plot
• #5623: Communication with EMPower Sensoren 7002-006
• #5624: Report Generator codes for Radiated Emission Burst tests
• #5697: Display R&S ESR3 trips and measurement failures

RadiMation version 2014.2.2

• #2575: Error dialog doesn't show icon in taskbar
• #3870: Report genaration on chinese pc is not working as there is a tab block in the insert file.
• #4004: Report generator code for emission tests in multiband
• #4100: First sweep from Agilent MXE is sometimes wrong
• #4128: Driver: Agilent N9038A in FFT mode
• #4290: No input 1 HP-8568B Spectrum Analyser
• #4400: Statements for sorting columns with a space
• #4660: No graph or table info during Attenuation Calibration
• #5204: Arithmetic operation resulted in an overflow
• #5241: Latch-up when CONFDVDR directory is invalid (no network access)
• #5276: Wrong device driver is selected or removed
• #5345: During Attenuation Calibration it is not possible to show graph
• #5370: RadiMation is always taking two sweeps
• #5382: Connecting issue with R&S BBA100
• #5405: Old test time and date information seems to be overwritten by current date and time
• #5420: Arithmatic operation resulted in an overflow
• #5425: Turntable is not set back to start position after final measurements
• #5439: Graph controls doesn't work
• #5464: RadiMation doesn't start after selecting the Chinese English language
• #5473: Driver Antenna ATR80M6G
• #5478: Object reference not set to an instance of an object
• #5495: Include Measurement values in Burst printout template
• #5502: Virtual Instrument Powermeter printing is freezing RadiMation
• #5503: Signal Power went to high with Amplifier 80S1G4
• #5508: Configuration of RadiMation is lost when the CONFDVDR is in a dropbox shared folder
• #5510: SC1000 initialization is taking a long time
• #5511: Unknown error Amplifier 250W1000B
• #5512: Agilent N5171B is generating error during init
• #5514: MXE receiver is not recognized
• #5517: Unit column description is not updated during LLF edit
• #5519: How to create a field probe correction?
• #5520: Turntable Wrong Command error 1
• #5521: Opening EUT is always showing default EUT directory instead of the last one used
• #5522: Checking if a device is connected from the results of a test is using the wrong addressing information
• #5525: Strange results with MXE receiver
• #5526: Implement Word Wrap for error code descriptions
• #5528: Strange error number for 'No LISN line or neutral selected' error
• #5531: R&S SME06 110 errors Output Unleveled ALC failure
• #5533: Antenna height is set with a small offset
• #5534: No network locations could be found
• #5535: Multiband settings could not be set by dropdown
• #5536: Driver: MicroRad 01E probe with NHT310 read out unit
• #5537: Repetition interval is using an enormous amount of memory for a scanning receiver
• #5538: Driver Narda EFA-300 Field Sensor
• #5540: RGN6000A timeout expired before operation completed error
• #5549: Dialog for Product standard is not high enough, and thus doesn't allow to add basic standards
• #5559: Current and Calculated Current cannot be included in the Enhanced status window
• #5560: The location and size of the enhanced status window is not remembered
• #5566: LAN control of the R&S ESPI Controlled LISN
• #5569: Polar plot is not updated when continuous measurement is activated and the turntable is started to be moving

RadiMation version 2014.2.1

• #1907: When RadiMation is minimized during report generation, RadiMation can not be restored again to its original size
• #2562: Error dialog that is shown for a minimized RadiMation program cannot be activated
• #3792: Selection bar at main screen disappears after opening a test
• #5437: Plot graph 'Zoom out' button should be 'Full Span'
• #5630: Test would not start