Release Notes/Solved items Version 2015.2
Contents
RadiMation version 2015.2.4
- #476: The CI configuration window is to small by default
- #2216: ESD has strange behavior when pre defined report generation is enabled
- #4498: Measuring settings Lines/Neutral with LISN
- #4607: Customize graphs not working
- #5322: Signal Generator setting the frequency raised an error
- #5954: R&S ESL 6 Scanning Receiver Specific System Error -222 Data out of range SCAN1:TIME 1 MS
- #6152: Incorrect behaviour of Save button after RE test
- #6251: R&S ESR7 specific System Error: -222 Data out of Range DISP:TRAC:Y:RLEV:0.0103DBM
- #6287: Driver: R&S ESL6 as Sensor power meter
- #6301: Preamplifier setting is not visible anymore in the CE MB TSF window
- #6303: HP 34401A message There is no Device Stream Configuration
- #6303: List of performed tests is not updated in the report generator, when a test is finished
- #6308: COM port setting is not remembered in the RadiMate IV device driver
- #6314: Is it possible to use mutlimeters or oscilloscopes for conducted immunity tests
- #6372: Can I take an existing graph / plot and generate an excel file with the frequency and amplitude data?
- #6647: RadiSense 6 fieldprobe connected by Radicentre 1 is raising an error
- #6793: How can the settings of an oscilloscope for the the Voltage measurement during a Conducted Immunity be set?
RadiMation version 2015.2.3
- #1864: Move during measurement checkbox is shown in unlogical state if multiple bands are selected.
- #5320: Folder name is changed to New Directory again
- #5744: After adding a TSF directory it doesn't show the renamed directory name directly
- #5894: DARE Homepage menu item name and link is incorrect
- #5898: Graph items and restore factory default are disabled for the Chart settings
- #5947: Modulation of Marconi 2024 Signal generator is never turned off during CI test
- #6202: Show the DeviceStream configuration of a device driver in a panel below a combobox
- #6243: Communication issue with a RadiSense IV connected by CTR1
- #6250: Advanced configuration dropdown boxes are not visible for the RadiSense IV driver
- #6286: Report generation doesn't replace all the codes
- #6289: CompleteBuild.py is not triggering a rebuild
- #6309: How to configure test setup files when using a low resolution?
RadiMation version 2015.2.2
- #703: Calibration Types
- #1922: No compression information in table form when performing a Compression test.
- #1923: No color difference in graph at Compression test
- #2288: Automated test for EFT
- #2289: Automated test for Surge
- #3812: EFT and Surge do not have seperate positive and negative pulse levels
- #5269: Frequency is not set during harmonic measurement
- #5285: Harmonics measurement (amplifier cal) is not working
- #5574: Harmonics measurement could be optimistic
- #5614: It is possible to start a test without an EUT opened
- #5737: EFT test duration field is required
- #5902: Not possible to remove test specific report generator template from items in the report generator settings list
- #5903: List sorting settings of the Report Generator Settings are not retained
- #6100: Device driver: Teseq NSG3040
- #6122: Common buttons on the Multiband status test window should be enabled
- #6129: Device driver: emtest EFT 500M
- #6132: Sequence number in PI MB EFT test is not updated
- #6137: Update list of available EFT-line couplings
- #6138: Update list of available Surge line couplings
- #6139: Driver: Haefely PEFT-Junior
- #6140: Selected Cable in EFT & Surge MB test is retained after it doesn't exists anymore
- #6141: Driver: GPIB support for emtest UCS500N
- #6144: Update the progress column of the EFT and Surge tests
- #6145: Implement the test repeat count for EFT and Surge tests
- #6146: Is Random Surge angle working correctly?
- #6148: Creating a new EFT MB TSF shows an empty screen
- #6164: Enable Amplifier harmonics and gain for all users with the Immunity module
- #6179: Units are not correctly shown initially in the BandsGrid control
- #6180: Only the duplicates bands should be selected after duplication in the BandsGrid control
- #6181: Up and down buttons of the BandsGrid control are flickering during changes
- #6182: Up and Down buttons in the BandsGrid control are swapped
- #6192: Move the 'Change' button of the units to the bottom right of the units
RadiMation version 2015.2.1
- #4354: Test data graph has become black
- #4398: Graphs (auto) scaling is not functioning as expected
- #4811: When start frequency is unchanged it's causing frequency range errors
- #5001: Allow to insert attachments in an EUT file
- #5002: Possibility to directly attach generated report to the EUT file
- #5524: File is probably corrupt, or it is created with a newer version of the software
- #5682: Tolerances of AD Channel are shifted after report generation
- #6015: Is it possible to perform the power delivery test on another frequency
