Release Notes/Solved items Version 2015.2.5

RadiMation version 2015.2.5

• #470: No buttons present for often used operations
• #510: No overview of of used equipment at start of a test
• #940: Predefine which graphs should be shown on the screen
• #3826: Show during measurement option in the graph line configuration window
• #4162: automatically add and show the configured and selected ad channels in the graph window during an RI measurement
• #4613: Calibration expire window should be a MDI client window
• #4641: Switching between graph and table should rename graph button to table info
• #5125: Closed loop measurements
• #5527: Label of Show details button should become Hide details when details are shown
• #5576: Driver: R&S OSP130 with option B102
• #5607: Add "Save Calibration As..." possibility
• #5661: Add Frequency range panel for Bonn BLWA drivers
• #5678: Enhanced status window description of vertical and horizontal is not directly clear
• #5985: ESR7 replies with error about AC_DC coupling on Channel2
• #6020: Show all activated AD-channels by default in the graph during a test
• #6027: Perform final measurements in EMI receiver mode with the Agilent MXE N9038A EMI receiver
• #6036: Ability to enter manual information at each disturbance frequency
• #6090: Start/stop time test fileds are not retained from 2014.2.12 to 2015.1.7
• #6123: RadiMation is not responding when Amplifier Control window is enabled
• #6251: R&S ESR7 specific System Error: -222 Data out of Range DISP:TRAC:Y:RLEV:0.0103DBM
• #6270: Raise an error when R&S NRP-Z55 power sensor is disconnected during test
• #6296: Device stream in the device driver system for http protocol using get and post
• #6297: Driver: USB-xSPDT-A18 series switch matrix
• #6299: R&S FSP30 spectrum analyzer option for FFT filters
• #6302: Driver: Tektronix RSA5100-series
• #6312: Timeout in communication with R&S ESPI after QP measurement
• #6321: Clear the input buffer of a configurable device driver directly after the connection is established
• #6322: Not possible to specify the Escape character in the configurable device driver
• #6323: Configurable switch matrix device driver sends the 'Turntable Changed' command before the turntable starts moving
• #6337: Turning off Pre-amplifier option (INP:GAIN:STAT OFF) without this option being available is raising an error for the R&S FSV
• #6340: No Unit is shown for test level
• #6343: Ability to disable determination of the dynamic range during the Attenuation / Gain system calibration
• #6345: Carrier Level command of the Configurable Signal generator is not transmitted if no Carrier On command is specified
• #6349: Driver Switch matrix ICS 4864
• #6354: QP Detector Measuretime of ESL6 is set to 10 ms
• #6360: Driver: Tektronix 2001 for fixed voltage test
• #6361: Ability to zoom in the frequency graph during the prescan phase of a MB Emission test
• #6362: Frequency of the graph in the report is different
• #6364: Too few spaces in the name of the graphline in a report generator code causes that the graph is not include in the report
• #6389: Update the Configurable Switch Matrix wiki knowledgebase page
• #6394: NI DAQ USB 6218 AD Converter default input min and max
• #6395: NI DAQ USB 6218 AD Converter channels 9-16 can't be used
• #6397: How to dirrectly reference from the Main Template to a Keyword for a certain test
• #6398: Driver: Tektronix TDS2024C Oscilloscope
• #6399: Driver: Tektronix AFG3252 Signal Generator
• #6400: Driver: IFI ST181-10 Amplifier
• #6403: Ability to use the FSV-3 Analyser controlled as powermeter in zero span mode
• #6405: ARFI7000 is not reading probe values
• #6410: Driver: ETS-Lindgren 8000-053 amplifier
• #6411: Driver: ETS-Lindgren 8000-034 amplifier
• #6412: Raise an error when R&S NRP-Z55 is disconnected during a test
• #6418: R&S FSV 40 Error -222: Data out of range DISP:TRAC:Y:RLEV -10 DBM
• #6426: Configurable Switch Matrix isn't correctly saving settings when user configured commands of During and/or After Test are cleared
• #6428: Device driver Check is erasing the selected correction file(s) in the device configuration screen
• #6432: Device drivers that are using GPIBRS232 should be converted to panels
• #6436: Selection of a correction file in a device driver configuration is not working
• #6438: Default frequency range of the EMCO / ETS-Lindgren antenna 3117
• #6439: Driver: All ETS-Lindgren 8000-series amplifiers
• #6441: Frankonia FC is raising an -101 error during test initialization
• #6442: What does the NRP settling time does?
• #6448: Correct frequency range of the ETS-Lindgren 8000-034 amplifier
• #6451: Frequency up / down for UFA calculation is not working
• #6453: Uniform Field Area (UFA) calculation should trigger a default auto-layout when calibrations are added or removed
• #6454: Not possible to use CAL files for the UFA when it contains different test distance
• #6455: Warnings related to wxEXPAND are shown when a wxWidgets dialog is shown
• #6459: ETS-Lindgren 8000-053 Device Not Connected
• #6462: How to set the RBW when the R&S FSP 40 is used as powermeter?
• #6465: Driver: ETS-Lindgren Antenna series
• #6467: Driver: R&S FSIQ 7
• #6471: 'Decrement' should be the default value for the PowerStep setting of the Amplifier Linearity test
• #6472: Settings that are normally protected for the administrator, can be changed when the dongle is not present
• #6474: After zooming in a graph the graph axis is no longer linked to center and span
• #6476: Save the configured Auto-Layout settings for the Uniform Field Area (UFA) calculation config
• #6477: Insert Row in a Correction file is not working if no row is present
• #6478: A new correction file should have 1 row by default
• #6479: A new row should be added to a correction file when the 'TAB' key is pressed in the last cell
• #6487: Driver: EUT Controller: Generic TCP/IP Status interface
• #6488: Python program to test/verify the Generic TCP/IP Status inteface
• #6491: Driver: Frankonia EMCL-20
• #6493: GPIB address of Frankonia FC06 cannot be changed
• #6504: Project: Remember which graphs should be shown
• #6505: Propose best implementation to remember graphs to be shown
• #6527: Ability to specify a frequency depending RBW for the R&S ESI Powermeter
• #6536: Unit-test for the C++ CenterSpanStartStopFrequency class
• #6537: In the testsite window, 'save as ...' should show the original name + ' - Copy' as the new suggested name
• #6571: Remove Row of a correction file selects the first row if the last row was selected
• #6572: Show a message with the used coupling value for the virtual coupler
• #6577: Project: Telefication: Substitution measurement investigation
• #6580: Showing the configuration window of R&S NRVS AD-Convertor crashes
• #6586: ETS-Lindgren HI-4422 VI_ERROR_INV_PARAMETER: Invalid Parameter error
• #6609: Update the splash screen logo of ETS to DARE!! Instruments
• #6620: Driver: Frankonia ALX-4000E / AXL-80
• #6624: Driver: Frankonia FLG-70C / FLH-200B1
• #6627: Make StandardPreAmplifer device drivers Configurable
• #6657: grid color always black
• #6664: Driver: R&S ESRP7 as powermeter
• #6717: Zero button should be shown for the FieldSensor Virtual Instrument
• #6726: How do I configure the RPR3006W power meter for remote control?
• #6735: Also show a magnifier button after the selection of the CONFDVDR directory
• #6796: Report generator code to retrieve the 'Device driver versions'