Release Notes/Solved items Version 2018.1

RadiMation version 2018.1.4

• #5261: Frequency plot can't be printed
• #5636: R&S ESPI 3 error Data out of range SCAN1:BAND:RES
• #5783: R&S ESU 26: Error -222: Data out of range. Depending on the preamplifier that is used
• #6373: R&S ESU 40: Error -222: Data out of range SCAN1:BAND:RES 1 KHZ
• #6811: Add new RadiMation startup Reseller logo
• #7329: Using multiple bands that switch preamplifier on and off gives error: R&S Receiver ESU 8
• #7482: RBW and SpanCentreFrequency order. Unable to set frequency multiband
• #7728: Unicode: clsFile EUT information is saved as ascii. Unicode characters are saved and read as '???'
• #8590: Unknown error when Visa is not installed, and is tried to control the EMCenter by LAN
• #8600: Spectrum Analyser frequency out of range with PreAmplifier MB
• #8691: Frequency out of range at second measurement.
• #8730: Source array was not long enough. Check srcIndex and length, and the array's lower bounds.
• #8734: controlling radigen over windows rs232 to com3 over usb is not working
• #9129: RadiMation crash when GPIB-Board is not installed or not configured correctly (GPIB-EDVR)
• #9177: Unable to open measurement files (_Object reference not set to an instance of an object..)
• #9188: Corrupt testfile, no data is visible in the graph
• #9221: Receiver (ID1691) Input 2: Specific System Error: -222,"Data out of range; SCAN1:BAND:RES 1 KHZ"
• #9247: Wrong output for Keyword ||DESCRIPTION||
• #9274: Driver: Field probe Narda EMC-30 RS232
• #9275: Driver: Passive drivers Philips Saeco S.p.A.
• #9277: Driver: Passive drivers CDVI Wireless S.p.A.
• #9278: MB test with Carad as eut controller gives an error
• #9287: Test data disappeared
• #9293: Radimation restarts during emission measurements (read/write outside the bounds of array)
• #9310: Testdata again not visible
• #9311: Test data lost / not visible
• #9314: No response turn table
• #9335: VI Window crash at closing
• #9338: Driver: Shaffner Broadband Horn Antenna 1-18 GHZ
• #9339: Driver: Stanford Research Systems - Model DS335
• #9341: Driver: Agilent N1913A
• #9345: De index ligt buiten de matrixgrenzen - Index out of range
• #9350: Signal power went too high (-6 dBm) during power delivery test
• #9363: Driver: CDN LAPLACE S46 ST8
• #9364: Driver: LISN LAPLACE (Cranage) LISN16A1P
• #9365: Driver: Antenna Laplace SA1020/RF200 No remote control
• #9366: Driver: Injection device Teseq KEMZ 801
• #9367: Driver: Calibration JIG Teseq KEMZ 801
• #9368: Driver: CDN MEB M3, M2, AF3-1 and AF2-1
• #9369: Driver: Antenna ARA LPB-2513
• #9382: Unable to ReportGenerate Emission and Peak Table
• #9394: Index was outside the bounds of the array.
• #9396: Index was outside the bounds
• #9398: Driver: Bonn BLMA 2060-30
• #9409: R&S ESI does not show graph of logarithmic stepped sweep
• #9426: Subject of ErrorReport should contain the description of the error
• #9428: Transmitting an ErrorReport is not working, complains that it is not possible to send ErrorReport
• #9440: Word locks documents after that it is not possible to print
• #9443: ErrorReport: "De bronmatrix is niet lang genoeg. Controleer srcIndex en de lengte ervan, en de ondergrenzen van de matrix. ".
• #9521: Peak table does not work in 2018 version
• #9524: Object reference not set to an instance of an object: clsCommandSetTurnTableAngle.IManualModeAsyncCommand_StartWork(
• #9525: Antenna Tower (ID1365) Aut.: Impossible to get description string for this Error! Probably an unknown RadiMation Error. Code: 805308669 (0x300008FD))
• #9538: Version Information is not displaying
• #9539: Text does not display on the devices tab in 2018.1.4
• #9549: Problem exporting conducted emission
• #9558: ErrorReport: "Access to the path 'C:\Users\u0058578a\Documents\My Music' is denied. "
• #9577: DARERSS2010I
• #9584: Question: What is AT. Is this used for low frequent rod or loop antenna?
• #9593: Vertical stripes QP measurements
• #9608: Unhandled exceptions

RadiMation version 2018.1.3

• #3570: Turntable Frankonia FC02 not working correctly
• #5984: Printing results of a burst test a second time, prints the same data as the first time
• #7219: Radifield powermeter is not usable on 800 MHz
• #7977: Holaday Instruments HI-4422: Invalid command
• #8014: Extend the maximum size of a generated Report
• #8031: Default graphs during Multiband Immunity are not shown during test
• #8162: Radimation startup crash Recursive customization file
• #8379: Object reference error in updating the Emission Graph.
• #8537: SMR40 total crash of communication
• #8585: Radiated Emission Magnetic field goes right into manual mode
• #8588: Field test level keyword missing.
• #8609: Agilent 34401 multimeter is always selecting DC coupling in CS101 calibration and CS101 test
• #8912: Object reference clsIDocumentBase.UpdateAllViews update graph
• #9112: No match was found in the specified regular expression
• #9116: Fax number on about screen is not valid anymore
• #9119: Sharing Monitoring AD channels between tests, and test setups.
• #9141: Radimation crashes, no error report
• #9173: MXE ERROR -224: Settings conflict; only active antenna unit available; no other y axis units
• #9181: File > New > EUT is showing a strange filename
• #9195: RF Amplifier (ID1647); Device not connected
• #9253: Add the name and identifier of the Reseller as it is programmed in the dongle in the ErrorReport
• #9254: Add the identifier of the dongle in the ErrorReport
• #9263: Unhandled exception handler is crashing software before report can be transmitted
• #9271: Radimation stops: software tries to change RBW on R&S ESU 8
• #9272: RadiMation keeps waiting: RBW value changed by R&S ESU 8
• #9282: Problem using the EMS RSC controller
• #9283: Cannot Find the device driver (RPR2006P)
• #9285: R&S ESU 8 Input 2 Scanning Receiver: Specific System Error: -200,"Execution error;Function not available;ABORT"
• #9302: BLMA 1040-100D
• #9306: Incorrect table export of polar plot
• #9307: No match was found in the specified regular expression
• #9309: ErrorReport: "Rohde & Schwarz ESR 7 Input 1 Scanning Receiver: Specific System Error: -200,"Execution error; Function not available; ABORT""
• #9343: Driver for: Teseq CBA 16-150
• #9347: ErrorReport: "Fixed power test. Vrijdag Einde vd dag
• #9351: ReportError("Exception has been thrown by the target of an invocation.")
• #9352: Cannot install CTR 1001S in win 10
• #9370: ErrorReport: "Cannot find the device driver.
• #9509: Install issues due to download problems
• #9534: Decimal sign changes after radimation error
• #9546: Signal power went too high (-4 dBm) during power delivery test
• #9550: Keywords not woking in Radimation_Validation_Template v 4.2
• #9553: EN61000-4-6 Callibration and testing with two powermeters
• #9557: Rohde & Schwarz ESPI 3: Specific System Error: -200,"Execution error; Function not available; CALC:UNIT:POW DBUV
• #9560: ErrorReport: "File 'J:\postvak\testsite\Referentie metingen\Radiated Immunity Semi Anechoic Chamber EN61000-4-3\ID1494 - Cavendish\RI 80-1000MHz 10Vm AVG 2ndQ 2011.BMP' not found during a 'ShellExecute' call "
• #9588: Missing/empty cells in peak table
• #9594: Error .csv dump LeCroy Wavesurfer
• #9660: TSF file name changed.
• #9667: Not able to connect to devices in radi-centre

RadiMation version 2018.1.2

• #4209: No frequency verification on correction file
• #8718: HP3478A Multimeter wrong mode selection.
• #8986: No graphline is shown anymore in the polar plot of a peak
• #9136: Driver: HP 85420E Pre-amplifier
• #9145: Driver: Aaronia antennas
• #9245: DARE!! Instruments RPR2006C--FWD: No match was found in the specified regular expression.
• #9270: Using R&S Z91 as monitoring power sensor with attenuation (-30 dB) takes a long time to measure
• #9403: RI: Certain graph lines are not added to the report. Outputing a table does work.
• #9663: Radisense 10 RSS2010B/H cor. OFF: I2C Not-Acknowledge (NACK) "

RadiMation version 2018.1.1

• #8567: Include Sentinel System Driver 7.6.0 in setup program
• #8720: Power is sometimes regulated below the desired testlevel of 1 watt
• #8773: Configurable RS232 stream always appends \n after command
• #8865: PDF icon for the manual on the desktop is always using a white icon. Not showing the PDF icon