Release Notes/Solved items Version 2023.2

RadiMation version 2023.2.6

• #12424: INNCO CO3000 firmware vesion 1.03.09 has problem with retrieving polarisation
• #13474: Drivers added for the EMI mode of the Rigol RSA3000-series and RSA3000E-series
• #13630: Added Possibility to configure the preselector of the TDEMI series
• #13811: Improved retrying to resolve Error 130 when controlling RadiPol antenna tower
• #13883: Fixes related to loading the advanced settings
• #13967: Enable alignment warnings for the N9038A
• #14112: N9010B Wrong RBW in Final Peak Measurement
• #14112: N9010B Wrong RBW in Final Peak Measurement
• #14146: Rigol analyzer returns unexpected results during BCI Calibration
• #14219: Rigol RSA-series analysers: Socket based communication on port 5555 now possible
• #14220: Possible to control Rigol RSA3030E on LAN port 5555
• #14221: *OPC? is also included in the RadiLog when TCPIP device stream is used
• #14241: RE TDEMI buffers a sweep taken before the pre-amp is state is changed
• #14257: Driver: AMP 2104
• #14264: Firmware version check for Rigol RSA3000E series is now checking on firmware version 00.01.04
• #14295: Unit not changing to dBuA from mA in CS114
• #14297: Gauss Instruments TDEMI controlled in spectrogram mode uses actually taken number of sweeps for second detector
• #14299: Fieldfox N9912A Check correct option values
• #14310: Driver Wavecontrol SMP 3
• #14313: Limit line must be enabled for the measured detector type
• #14316: Correct default TCP/IP port number is selected again when it is removed from the Ethernet address configuration
• #14316: Set the default port in the TCPIP communication string if it is removed during configuration
• #14317: More securely pass variables to multithreaded combine of correction files
• #14322: Extend configurable amplifier drivers to perform an additional optional read
• #14326: Changed description of the graph division settings frame
• #14329: Changing the 'max measure' in the powermeter settings is not possible using the keyboard
• #14341: Driver for adjustment of RadiField amplifier input attenuator
• #14342: Driver for advanced measurement values of RadiSense Ultra
• #14350: Keysight N9000: Fix Wrong RBW during final measurement
• #14357: Do not start the RadiField gain adjustment while this is already started
• #14370: Improved auto detection of actual terminator used by Raditeq devices
• #14376: SMF100A carrier is limited to minimum level
• #14376: SMF100A carrier is now limited to the minimal possible level
• #14377: Driver: R&S EPL
• #14379: Support the RS OSP B103 module
• #14382: Revert change which sends an unsupported command to the SMB100B related to setting the minimal carrierlevel
• #14399: Keysight N9000: Meter average detector is set in receiver mode
• #14409:Error in Av measurement during CE
• #14415: R&S ESRP: Correctly select the fixed attenuation value when the same as the auto attenuation value
• #14420: Increase the power measurement observation time of RadiPower when measuring AM modulation
• #14421: Requesting the average trace in the pre-scan results in unexpected data returned
• #14423: Rigol RSA3030E-TG is used in GPSA mode instead of EMI mode
• #14432: Improved initialisation time of a USB connected RadiPower RPR2006P
• #14433: Siglent generator time out problem when sending the OPT command
• #14448: Baudrate of RadiPower RPR2006 is not set again if it is already using that baudrate
• #:14471: Device driver message boxes should show the brand and description
• #14484: Power Meter Boonton 4220A not recognized
• #14491: Firmware update of RadiPower 4000 series does not raise an 'ERROR 1' anymore
• #14492: RadiPower driver waits until unit has finished restart after a firmware update
• #14493: Corrected typing error 'faling' to 'falling'
• #14509: Checking for updates raises a 'server cannot be found' error
• #14539: R&S SMC100A is always set to 0 dBm
• #14546: Error when controlling a R&S NRP connected to a R&S SMB100A
• #14550: Update version number checks in driver for RadiSense Ultra
• #14559: Low and High range selection for the Radisense 3018U
• #14560: TSF is not blank anymore after click cancel in sequence window
• #14585: Driver: Ceyear 1465-series and 1466-series signal generators
• #14586: Two dongles are now correctly supported
• #14596: RepGen: Possibility to reapply the table styles to a table
• #14603: Raditeq RadiSense RSS3018U: The range selection is by default hidden
• #14605: OSP B103 module does not remember selected state
• #14607: Generating a report using the RADICLI.EXE is only possible when the desktop client is running
• #14611: ESU40 Receiver does not return data when measuring bands with a 0 Hz span
• #14613: RadiSense 3018U: Do not request device specific inputs related to the laser temperature and current
• #14615: Radimation Closed after choosing multiple Files in EUT-Attachments Tab

RadiMation version 2023.2.5

• #13291: Read all trace data when multiple detectors are active for a TDEMI
• #13512: Error of invalid process is not shown anymore after SHIFT+Advanced click
• #13536: Radimation 2022.3.6 crashs after each test when using two dongles.
• #13764: SG386 pulse modulation
• #13813: RadiMation hangs at the end of the test when multiple dongles are connected to the PC
• #13920: Driver request: Stanford Research SG386 RF Signal Generator
• #14005: Rigol RSA series: Additional sweep is taken after QP detector is activated to allow to level to correct amplitude
• #14010: Problem with RadiMation and the polarisation of the Frankonia FC06
• #14064: Rigol RSA series: Additional sweep is taken after QP detector is activated to allow to level to correct amplitude
• #14111: Driver: ETS-Lindgren EMSense 7007-203
• #14117: Apply cable correction to the magnetic field calibration
• #14121: Driver: A-info DS-3100
• #14122: Driver: A-Info LB-OH-650-10-C-SF
• #14123: Driver: A-Info LB-2080-SF
• #14124: Driver: Aeroflex 2025
• #14125: Driver: Agilent Technologies 83731A
• #14126: Driver: A-Info 62EWGS-A1
• #14127: Driver: A-Info 90EWG3.5-T02-A1
• #14128: Driver: EMC Partner ESD3000
• #14130: Driver: Tekbox current probes
• #14131: Driver: Tekbox Bulk current injection devices
• #14133: MCU antenna tower position progress calculation issue
• #14136: Driver: Injection device: Schloeder EMCL-20 and Schloeder EMCL-35
• #14148: High attenuation required for measuring the fundamental results in upper harmonics being measured in the noise.
• #14149: Adjust drivers to use the correct name for A-INFO
• #14154: Rigol DSA832: Additional sweep is taken after QP detector is activated to allow to level to correct amplitude
• #14156: Can HTTP communication be used to retireve information from JSON
• #14160: Rigol DSG3065B does not support SYST:ERR?
• #14161: Textronix AFG3251C reports event messages as errors
• #14166: HI-6105 cannot save settings when pressing the OK button
• #14176: CWS500 as receiver does not work
• #14177: Object reference error opening Graph Export window
• #14186: Error when using RS PRO analyzer as power meter
• #14194: Data returned from Tektronix TDS oscilloscopes are calculated using 10 vertical divisions
• #14194: Improved selection of to be transferred waveform from older Tektronix TDS oscilloscopes
• #14195: Driver: RadiSense RSS2010M
• #14199: HP E4419A cannot be found because the identification string cannot be changed
• #14201: EMSense 7007-203 drivers
• #14218: Wrong settings are sent to the VDI device
• #14223: HP E4419A dual power meter error during zero operation
• #14224: Process (PID number) not found after closing Notepad
• #14225: Frankonia FC06.1 wait after height change to finish INIT procedure
• #14226: Manual EFT configuration does not indicate the unit in which configured values are expressed
• #14229: Driver: Tekbox TBMA4
• #14230: Driver: Tekbox TBL 5032-3
• #14232: Driver: Kalmus 320 FC
• #14233: Driver: Kalmus 711-FC-CE
• #14234: Driver: Teseq T800
• #14235: Driver: FCC-801-M2-50A
• #14236: Driver: FCC-801-M3-16A
• #14237: Driver: FCC-801-M5-16A
• #14238: Driver: EM Test ESD 30
• #14243: Driver: Prana N-MT500DC
• #14245: Magnetic field test according ISO 11452-8 time outs when using the Configurable multimeter driver
• #14251: Adjusted start frequency to 9 kHz of Raditeq GTM0250A, GTM0500A and GTM1000A
• #14255: Powermeter Fail
• #14256: Regulation of initial step of a non linear amplifier is now using the configured default gain
• #14259: HP4418 added option to enable the step detector and send the sense speed
• #14261: Raise error if the selected filter setting is not allowed for current RadiPower firmware
• #14262: Driver: Hameg 8135
• #14263: R&S SMH Allow configuring of 10kHz-2GHz range
• #14265: Standard socket port of the Rigol RSA-series is port 5555
• #14267: Fix Strange layout of stirrer configuration panel
• #14268: Select tuned mode as the default stirrer type
• #14275: Driver: Boonton 4220 powermeter
• #14287: Driver: IFI T188-50
• #14288: Driver: Klein+Hummel SA602 amplifier
• #14289: Driver: OPHIR RF 5041

RadiMation version 2023.2.4

• #5383: Implement 'Ignore height change' settings for the NCD AT
• #6879: Maturo MCU cannot ignore height change
• #9153: Average too high in Final Measurement sweep
• #9332: Final Measurement - average
• #12081: Average of phase is not correctly calculated when Phase is crossing 180 degrees
• #12150: AD-Convertor device driver as a Decorator around a spectrum analyser driver to measure AM/FM/Pulse-modulation
• #12236: Driver: Rigol RSA5065 to use multiple traces in EMI mode
• #12482: Support tracking generator on Rigol RSA5065
• #12797: Driver: Rigol RSA5065 EMI-Mode
• #12799: Rigol RSA5065 Tracking generator
• #13049: Driver: Siglent SVA1032X
• #13402: Measurement using Cispr AVG detector in the EMI-Mode of the Rigol RSA5065N
• #13602: I/O Error with Rigol RSA5065
• #13688: It takes long to open emission data files
• #13749: Report generator deletes grid found in template file when generating report
• #13772: Driver: Agilent 34410A
• #13844: Driver: Spectrum analyser driver for multimeter in CWS500N3
• #13857: Qpeak not visible in peak table after making adjustments to the peak table.
• #13883: Unexpected oscilloscope behavior in CS101 test
• #13987: Re-implement MCU antenna tower limits as pure software limits,
• #13924: The name or number of the point in the UFA calculation cannot be modified
• #13932: Differences in generated reports
• #13939: Include more logging during start of RadiMation to identify what causes startup time
• #13956: The last used graph exporter type should be remembered
• #13983: Environmental information is inserted as boolean value in RI printout reports
• #14000: Rigol RSA5065 Communication Error
• #14017: Driver: KRE 4000 extend with ethernet control
• #14031: RadiSense has invalid user calibration table.
• #14038: Implemented a change to not reduced the sweep time when the average or rms detector is activated for r&s esu based drivers like the esw
• #14041: It is not possible anymore to use a key on the keyboard to select an entry from a dropdown list
• #14053: RSA5065(EMI mode): RBW cannot be set to 9 kHz, changes back to 1 MHz
• #14054: AR FM5004 Driver issue with channel selection
• #14055: conducted emission in RSA5065 EMI mode
• #14058: RE MB QP missing in the table
• #14063: FA 7006 Issue with termination characters on legacy commands
• #14076: Hide the "Move antenna height" and Move distance" setting from the change order
• #14080: Driver: Siglent SSG5060X
• #14081: Radiated Immunity MB test is corrupt in 2023.2.3
• #14082: Plugin cards are not auto detected in RadiCentre Ultra 8
• #14085: Add Advanced option:"Emission.Multiband.Sequence.AllowPeakReview"
• #14086: Driver PMM 6630 does not handle *** correctly
• #14092: Improvement Amplifier linearity, remove 10dB Limit?
• #14095: Driver: ETS-Lingren 3166 & 3167 TEM Horn antennas
• #14097: Multiband GTEM not possible to configure the antenna distance
• #14099: Emission test using Rigol RSA5065 - Analyzer Reference Level not as defined
• #14100: RadiCentre returns VI_INP_PROT error when the expected response size is less than the actual response size
• #14102: Averaging of phase
• #14113: ESD Keywords are not working
• #14114: Repetition rate has no unit in report in EFT Report.
• #14116: More antenna steps in MB GTEM test results in unexpected results
• #14119: Turn table min/max positions are incorrect
• #14175: Antenna with Power Meter as "Field Probe"
• #14206: Change LumiLoop 2.0 calibration mode to put back the original settings after the test.
• #14207: Electrical Field could not be regulated to the desired test-level
• #14210: Improved auto attenuator selection on R&S ESW input 2 with pulse limiter
• #14211: DSG3065B raises error when am modulation is used above 3.6 GHz
• #14242: Time out error controlling the U2009A power meter
• #14249: EUT Controller TESTINFO doesn't work
• #14277: Error setting the sweep time while using the CAV detector

RadiMation version 2023.2.3

• #12894: OPC Driver does not work
• #13901: ESIB 7 error
• #13913: Extend Bonn amplifier driver to reset water cooling interlock error at retry
• #13925: The start position should be allowed to be higher than the end position of the X-orientation of the probe positioner
• #13926: The start position should be allowed to be higher than the end position of the Y-orientation of the probe positioner
• #13938: Change the x-position and the y-position generator to behave as an uni-directional generator by default
• #13951: Extend manual or add application note regarding usage of axis specific correction factors of field probes
• #13955: Add 4 steps as a default possible options for the XY positioner step count
• #13957: ESR TD driver has a resolution configuration which is not expected
• #13965: UFA Calculation not possible due to unspecified tolerance in calibration files - Field closed loop method
• #13966: Maturo NCD turntable time expired before operation completed
• #13978: Multiband: UFA calibration seems to regulate to an average field greater than the specified tolerance
• #13996: index outside the bounds
• #14011: Maturo NCD Turntable: Timeout expired before operation completed.
• #14012: EMPower 7002-009 010 option 010 not detected
• #14016: Extend the Maturo NCD Antenna tower to send the height with fractions.
• #14023: R&S ESRP3 Analyser has a default port of 7895 this should be 5025
• #14026: Amplifier Research FL 7006: Not all bytes are written to the GPIB-Board within the timeout period (GPIB: EABO)
• #14029: EN61000-4-3:2020 Constant Power method is interpreted as being constant field method in the UFA configuration dialog
• #14033: Driver: Raditeq GTEM RGT0250A, RGT0500A, RGT1100A
• #14049: Configurable Power meter clear input buffers before getpower.
• #14052: RSA5065(GPSA mode) is not switching to EMI mode for the final detector measurement
• #14067: Support RF mixer in front of Keysight N9020B MXA
• #14145: RadiMation cannot connect to the R&S NRP powermeters anymore

RadiMation version 2023.2.2

• #13849: Manual XY Positioner does not show message when first position is X=0, Y=0
• #13851: The tab order of the X/Y positioner settings of the field distribution is very unlogical
• #13584: The virtual X/Y-positioner has advanced configuration settings which is unlogical
• #13858: Setting start-x and end-x in Field Distribution configuration is not possible
• #13877: NGS3040 set default port configuration to 1025
• #13934: CTR1009B USB drivers

RadiMation version 2023.2.1

• #9240: Negative combobox values with unit distance (grootheid) are getting different smaller units (eenheden)
• #9241: Spin control of ctlsetting xy positioner comboboxes only checks closest allowed value when the unit is not centimeters
• #9243: BusyStatusBar of the xy positioner progression status displays the distances with the wrong units as extension
• #9832: Driver Maturo FPP2.3 Biaxial Positioner
• #12157: EN 61000-4-3:2020 is not mentioned in the UFA calculation window
• #13408: XY positioner parameters are reset during configuration
• #13411: The continue settings for the XY positioner only shows a selection for the X position
• #13502: Restrict usage of XY positioner using RadiMation Essential license
• #13503: Change the order of the XY positioner configuration controls
• #13504: Possibility to enter the positioner distances with millimeter accuracy
• #13505: Set the correct values for the XY positioner in the advanced settings
• #13506: Show and use the X position setting in the change order
• #13507: Show and use the Y position setting in the change order
• #13508: Separation of command generators, applicable settings and driver interfaces for the X- and Y-axis movement of a field probe positioner device driver
• #13510: Add switch matrix events related to the Y positioning of the field probe positioner
• #13511: Add switch matrix events related to the X positioning of the field probe positioner
• #13513: Show the antenna and antenna tower controls when the field distribution location type is selected
• #13631: Add a stop button for the manual mode XY- Positioner
• #13632: Parallel control of current, voltage, switch matrix and eut controller
• #13634: UFA calibration export tool
• #13736: EN 61000-4-3:2020 is not mentioned in the UFA calculation window
• #13741: IEC 61000-4-3:2020 specifies that the amplifier is linear if the 5.1 dB step results in a 3.1 to 7.1 dB change
• #13791: Calculate average and float unit test fails in VS 2022
• #13805: Calibration export tool file validators, keeps detecting already deleted cal files