Release Notes/Solved items Version 2023.2

RadiMation version 2023.2.3

• #12894: OPC Driver does not work
• #13901: ESIB 7 error
• #13913: Extend Bonn amplifier driver to reset water cooling interlock error at retry
• #13925: The start position should be allowed to be higher than the end position of the X-orientation of the probe positioner
• #13926: The start position should be allowed to be higher than the end position of the Y-orientation of the probe positioner
• #13938: Change the x-position and the y-position generator to behave as an uni-directional generator by default
• #13951: Extend manual or add application note regarding usage of axis specific correction factors of field probes
• #13955: Add 4 steps as a default possible options for the XY positioner step count
• #13957: ESR TD driver has a resolution configuration which is not expected
• #13965: UFA Calculation not possible due to unspecified tolerance in calibration files - Field closed loop method
• #13966: Maturo NCD turntable time expired before operation completed
• #13978: Multiband: UFA calibration seems to regulate to an average field greater than the specified tolerance
• #13996: index outside the bounds
• #14011: Maturo NCD Turntable: Timeout expired before operation completed.
• #14012: EMPower 7002-009 010 option 010 not detected
• #14016: Extend the Maturo NCD Antenna tower to send the height with fractions.
• #14023: R&S ESRP3 Analyser has a default port of 7895 this should be 5025
• #14026: Amplifier Research FL 7006: Not all bytes are written to the GPIB-Board within the timeout period (GPIB: EABO)
• #14029: EN61000-4-3:2020 Constant Power method is interpreted as being constant field method in the UFA configuration dialog
• #14033: Driver: Raditeq GTEM RGT0250A, RGT0500A, RGT1100A
• #14049: Configurable Power meter clear input buffers before getpower.
• #14052: RSA5065(GPSA mode) is not switching to EMI mode for the final detector measurement
• #14067: Support RF mixer in front of Keysight N9020B MXA
• #14145: RadiMation cannot connect to the R&S NRP powermeters anymore

RadiMation version 2023.2.2

• #13849: Manual XY Positioner does not show message when first position is X=0, Y=0
• #13851: The tab order of the X/Y positioner settings of the field distribution is very unlogical
• #13584: The virtual X/Y-positioner has advanced configuration settings which is unlogical
• #13858: Setting start-x and end-x in Field Distribution configuration is not possible
• #13877: NGS3040 set default port configuration to 1025
• #13934: CTR1009B USB drivers

RadiMation version 2023.2.1

• #9240: Negative combobox values with unit distance (grootheid) are getting different smaller units (eenheden)
• #9241: Spin control of ctlsetting xy positioner comboboxes only checks closest allowed value when the unit is not centimeters
• #9243: BusyStatusBar of the xy positioner progression status displays the distances with the wrong units as extension
• #9832: Driver Maturo FPP2.3 Biaxial Positioner
• #12157: EN 61000-4-3:2020 is not mentioned in the UFA calculation window
• #13408: XY positioner parameters are reset during configuration
• #13411: The continue settings for the XY positioner only shows a selection for the X position
• #13502: Restrict usage of XY positioner using RadiMation Essential license
• #13503: Change the order of the XY positioner configuration controls
• #13504: Possibility to enter the positioner distances with millimeter accuracy
• #13505: Set the correct values for the XY positioner in the advanced settings
• #13506: Show and use the X position setting in the change order
• #13507: Show and use the Y position setting in the change order
• #13508: Separation of command generators, applicable settings and driver interfaces for the X- and Y-axis movement of a field probe positioner device driver
• #13510: Add switch matrix events related to the Y positioning of the field probe positioner
• #13511: Add switch matrix events related to the X positioning of the field probe positioner
• #13513: Show the antenna and antenna tower controls when the field distribution location type is selected
• #13631: Add a stop button for the manual mode XY- Positioner
• #13632: Parallel control of current, voltage, switch matrix and eut controller
• #13634: UFA calibration export tool
• #13736: EN 61000-4-3:2020 is not mentioned in the UFA calculation window
• #13741: IEC 61000-4-3:2020 specifies that the amplifier is linear if the 5.1 dB step results in a 3.1 to 7.1 dB change
• #13791: Calculate average and float unit test fails in VS 2022
• #13805: Calibration export tool file validators, keeps detecting already deleted cal files