Release Notes/Solved items Version 2023.2.6
RadiMation version 2023.2.6
- #12424: INNCO CO3000 firmware vesion 1.03.09 has problem with retrieving polarisation
- #13474: Drivers added for the EMI mode of the Rigol RSA3000-series and RSA3000E-series
- #13630: Added Possibility to configure the preselector of the TDEMI series
- #13811: Improved retrying to resolve Error 130 when controlling RadiPol antenna tower
- #13883: Fixes related to loading the advanced settings
- #13967: Enable alignment warnings for the N9038A
- #14112: N9010B Wrong RBW in Final Peak Measurement
- #14112: N9010B Wrong RBW in Final Peak Measurement
- #14146: Rigol analyzer returns unexpected results during BCI Calibration
- #14219: Rigol RSA-series analysers: Socket based communication on port 5555 now possible
- #14220: Possible to control Rigol RSA3030E on LAN port 5555
- #14221: *OPC? is also included in the RadiLog when TCPIP device stream is used
- #14241: RE TDEMI buffers a sweep taken before the pre-amp is state is changed
- #14257: Driver: AMP 2104
- #14264: Firmware version check for Rigol RSA3000E series is now checking on firmware version 00.01.04
- #14295: Unit not changing to dBuA from mA in CS114
- #14297: Gauss Instruments TDEMI controlled in spectrogram mode uses actually taken number of sweeps for second detector
- #14299: Fieldfox N9912A Check correct option values
- #14310: Driver Wavecontrol SMP 3
- #14313: Limit line must be enabled for the measured detector type
- #14316: Correct default TCP/IP port number is selected again when it is removed from the Ethernet address configuration
- #14316: Set the default port in the TCPIP communication string if it is removed during configuration
- #14317: More securely pass variables to multithreaded combine of correction files
- #14322: Extend configurable amplifier drivers to perform an additional optional read
- #14326: Changed description of the graph division settings frame
- #14329: Changing the 'max measure' in the powermeter settings is not possible using the keyboard
- #14341: Driver for adjustment of RadiField amplifier input attenuator
- #14342: Driver for advanced measurement values of RadiSense Ultra
- #14350: Keysight N9000: Fix Wrong RBW during final measurement
- #14357: Do not start the RadiField gain adjustment while this is already started
- #14370: Improved auto detection of actual terminator used by Raditeq devices
- #14376: SMF100A carrier is limited to minimum level
- #14376: SMF100A carrier is now limited to the minimal possible level
- #14377: Driver: R&S EPL
- #14379: Support the RS OSP B103 module
- #14382: Revert change which sends an unsupported command to the SMB100B related to setting the minimal carrierlevel
- #14399: Keysight N9000: Meter average detector is set in receiver mode
- #14409:Error in Av measurement during CE
- #14415: R&S ESRP: Correctly select the fixed attenuation value when the same as the auto attenuation value
- #14420: Increase the power measurement observation time of RadiPower when measuring AM modulation
- #14421: Requesting the average trace in the pre-scan results in unexpected data returned
- #14423: Rigol RSA3030E-TG is used in GPSA mode instead of EMI mode
- #14432: Improved initialisation time of a USB connected RadiPower RPR2006P
- #14433: Siglent generator time out problem when sending the OPT command
- #14448: Baudrate of RadiPower RPR2006 is not set again if it is already using that baudrate
- #:14471: Device driver message boxes should show the brand and description
- #14484: Power Meter Boonton 4220A not recognized
- #14491: Firmware update of RadiPower 4000 series does not raise an 'ERROR 1' anymore
- #14492: RadiPower driver waits until unit has finished restart after a firmware update
- #14493: Corrected typing error 'faling' to 'falling'
- #14509: Checking for updates raises a 'server cannot be found' error
- #14539: R&S SMC100A is always set to 0 dBm
- #14546: Error when controlling a R&S NRP connected to a R&S SMB100A
- #14550: Update version number checks in driver for RadiSense Ultra
- #14559: Low and High range selection for the Radisense 3018U
- #14560: TSF is not blank anymore after click cancel in sequence window
- #14585: Driver: Ceyear 1465-series and 1466-series signal generators
- #14586: Two dongles are now correctly supported
- #14596: RepGen: Possibility to reapply the table styles to a table
- #14603: Raditeq RadiSense RSS3018U: The range selection is by default hidden
- #14605: OSP B103 module does not remember selected state
- #14607: Generating a report using the RADICLI.EXE is only possible when the desktop client is running
- #14611: ESU40 Receiver does not return data when measuring bands with a 0 Hz span
- #14613: RadiSense 3018U: Do not request device specific inputs related to the laser temperature and current
- #14615: Radimation Closed after choosing multiple Files in EUT-Attachments Tab
