Difference between revisions of "Release Notes/Solved items Version 2024.1.2"
(Created page with "== RadiMation version 2024.1.2 == * #8756: Virtual Instrument amplifier window. Triangle button is not drawing a triangle * #12693: A correction file that is opened by a restr...") |
(No difference)
|
Latest revision as of 15:13, 10 April 2024
RadiMation version 2024.1.2
- #8756: Virtual Instrument amplifier window. Triangle button is not drawing a triangle
- #12693: A correction file that is opened by a restricted engineer can still be modified by using TAB
- #13711: Fix for error 'Error: Objects used together must be created from the same factory instance. (Exception from HRESULT: 0x88990012)'
- #13819: Added EN61000-4-20:2022 UFA Calculation and TEM mode verification
- #13826: Update to DevExpress 23.2.3
- #13873: Driver: EMCO 5390 XYZ Positioner
- #13916: 2 or more calibration files can be opened at the same time again
- #13921: Show the default button in the Raditeq skin more distinctive
- #13967: Keysight N9038A: Alignment status is not checked during test
- #14150: Simplify selection of the type of the RadiCentre when a RadiCentre Ultra 8 is controlled
- #14283: On/Off buttons should not behave as toggle buttons
- #14315: Textboxes in word templates disappear
- #14323: Driver: Rohde & Schwarz SMB100M
- #14331: A readonly TSF file can still be saved by selecting 'Are you sure to replace it?'
- #14354: Objects used together must be created from the same factory instance. (Exception from HRESULT: 0x88990012)
- #14411: RadiCentre selection is always set to 'RadiCentre Ultra'
- #14413: Raise warning when main template is used as test specific template
- #14419: Returned value of SwitchHoldContinuousOff is always ignored
- #14437: Error while measuring with R&S FPC1500
- #14438: Objects used together must be created from the same factory instance
- #14438: Objects used together must be created from the same factory instance
- #14443: For RadiCentre devices when directly connected to the pc it is not possible to change the baudrate
- #14443: Allow baudrate change for RadiCentre1 devices connected by RS232
- #14444: No response from directly connected RadiPower
- #14446: Error while clicking table
- #14451: Fixed firmware check for the RPR2006C
- #14453: Improve battery check speed for raditower
- #14470: Error opening EUT calibration test graph "attenuation"
- #14472: Implemented a check if the Maturo FCU is enabled and referenced
- #14516: AR75S1G6C was not going to operate
- #14518: No stirrer driver in test site in normal RI MB closed loop test
- #14520: Amplifier not powering on
- #14523: Allow internal and external AM sine and square wave modulation for the R&S SMF100A generator
- #14547: Copying a limit line file table does not consider the unit when pasted into another limit line file
- #14552: Not possible to copy and paste the address information
- #14554: Driver does not read power anymore during zero operation.
- #14564: Objects used together must be created from the same factory instance. (Exception from HRESULT: 0x88990012)
- #14568: Objects used together must be created from the same factory instance. (Exception from HRESULT: 0x88990012)
- #14583: RadiSense Ultra: Add hidden advanced ability to skip range selection
- #14583: RadiSense Ultra should wait until probe is active after laser is activated
- #14584: Agilent ESG-D (E4431B) is automatically switching int/ext reference.
- #14590: Allow pasting correction data in units different from the receiving correction file
