Release Notes/Solved items Version 5.8

RadiMation version 5.8.30

• #3863: report generator code horizontal and vertical max peak are not working correctly as the complete frequency range is not displayed.
• #3884: The configuration window of the configurable switch is not closing when pressing ok
• #3886: CANoe Analyser CLSID cannot be found
• #4007: Final measurement IF overload is not detected correctly
• #4013: Configurable amplifier is crashing when settings the frequency range, driverversion 2011-6-7

RadiMation version 5.8.29

• #2616: First point of a calibration is too low
• #3887: Agilent E4446A analyser should use the correct RBW setting for MIL-STD
• #4002: Power meter device driver Advantest 3361B is giving event Time out
• #4011: Reviewing Harmonic test is crashing RadiMation

RadiMation version 5.8.28

• #3867: Net power and calculated current on the CAN-bus
• #3999: Driver Spectrum Analyser HP E7405A does not work any more after return from agilent service point
• #4006: No prescan is done with FSV40
• #4009: No final measurement is done with FSP 3 and LISN in multiband

RadiMation version 5.8.27

• #2601: Test initialization window should also show the name of the test-site that is being initialized
• #3976: Agilent N9020A: Configurable number of points
• #3998: Driver for AR500A250A
• #4004: Report generator code for emission tests in multiband
• #4008: Measurement with HF-probe

RadiMation version 5.8.26

• #4003: Closing the Visa window is crashing RadiMation with new gcc compiler
• #3990: Driver: FSEA20
• #3986: Configurable power meter driver can not find expression value while the value is send over the GPIB bus
• #1942: No check for connected device is included in device driver of Marconi 6960

RadiMation version 5.8.25

• #3543: Unclear message when the RadiPower is not connected to the RadiCentre
• #3783: Advantest Analyser is not measuring CE peaks correctly with version 5.7.4
• #3903: Advantest R3361B analyser raises timeout errors in a Multiband Emission test
• #3937: Scope driver Multi band is decreasing the scale when the returned value is zero and the scale is still maximum
• #3988: Report Generator crashes when a ) is included in the template filename

RadiMation version 5.8.24

• #3920: Driver: Marconi 2390
• #3965: Is not possible to choose between EXT-AC and EXT-DC using the siggen HP8648A.
• #3979: Compression test fails when the amplifier has correction files attached
• #3980: device driver for amplifier AR 60S1G4
• #3982: Engineer system in RadiMation allows impossible selections and removals.
• #3983: Modulation is always marked red after stopping and continuing RI multiband test
• #3984: Allow more than 8 AD-channels

RadiMation version 5.8.23

• #3969: Selecting the lowest location type in a multiband Lisn test configuration results in a crash of the software
• #3975: Configured sweeptime of a band is not used, due to sweeptime/MHz calculation
• #3977: Changing reference level is not always allowed
• #3978: Agilent 4446A: Sweeptime is changing when detector is selected

RadiMation version 5.8.22

• #3964: Pauses in a sequence are crashing the software
• #3966: Peak not detected in conducted emission current probe test

RadiMation version 5.8.21

• #2162: Create base class for the RadiCentre drivers
• #3795: Adding the device driver version to the about screen of RadiMation
• #3921: Extend driver of RadiTower to control a seperate RadiPol
• #3967: Pause test can not be used; problem during creating it
• #3968: Multiband emission test files cannot be opened anymore.

RadiMation version 5.8.20

• #3960: HD 100 Antenna tower driver is always in max speed.
• #3948: Agilent E4446A is not keeping 50 sec sweeptime in multiband test

RadiMation version 5.8.19

• #3910: External AM sine and square is not working with the Agilent PSG E8257D
• #3932: Driver: AR FP4080 controlled as an AR FP3000
• #3949: Printout is not generating the same plot twice, and the printout during the test is a combination of both
• #3652: Conducted emission - current probe TSF is saved in conducted immunity folder
• #3956: Agilent E4440A as a powermeter
• #3957: Registration of STDOLE2.TLB Error message during installation on Windows 7
• #3958: Some device drivers are missing
• #3959: Report generator code AVERAGE DETECTOR uses information of Peak Detector

RadiMation version 5.8.18

• #3925: R&S FSV13 does supports scans from 10Hz
• #3926: RBW is not correctly set on the R&S FSV13
• #3927: Raditurn is giving already in progress after motor error
• #3934: Several Multiband Conducted Emission Current probe problems
• #3938: Incorrect limit line when using Merge function
• #3947: AD/dc selection in power meter driver advantest is giving problems
• #3950: Zoom-out an emission graph by drawing a reverse zoom-in box

RadiMation version 5.8.17

• #3922: Copyright is 2010 instead of 2011
• #3941: Agilent E4417A power meter is limited to 18 GHz
• #3942: Driver: Agilent N9000A
• #3943: Driver: Agilent N9030A
• #3944: FAQ is not explaining why the measured value of the field probe can be higher with the am modulation on.
• #3945: How does the cable calibration works in the wiki page
• #3946: explain what is the difference between a printout during the test and a print out in the eut window

RadiMation version 5.8.16

• #3905: Test sites are lost in from time to time without any leads.

RadiMation version 5.8.15

• #3924: Sweeptime is not set in the Agilent N9020A

RadiMation version 5.8.14

• #3876: Gaps in emisson graph after final measurement
• #3894: Function "Continuous Measure" can block RadiMation with an error warning
• #3895: Test-site from a band can not be chosen after pre-scan
• #3904: Setting of the sweep time of the HP 4395A is not possible
• #3909: Pre amplifier is not yet turned on while sweeping
• #3917: Nonexistent peak and wrong final measurement with PMM during conducted emission multiband tests
• #3918: FSH 3 is setting wrong detector
• #3928: Driver: HP 4396A

RadiMation version 5.8.13

• #1856: No possibility to specify the modulation depth and frequency for external AM modulation
• #3196: Driver: Agilent N9020A
• #3875: Question: Radiated Emission Multiband: Order of measured peaks in the final measurement
• #3896: Older test results show a low resolution Multiband Emission graph
• #3902: The command ||LISN LINE|| is not recognized anymore by the report generator
• #3906: Scaling of the graphs can make the AD convertor graphs unusable
• #3907: Angle and height of detected peaks are always the same (in singleband emission)
• #3908: Agilent 4446A cannot be used below 9 kHz
• #3911: Driver: Agilent 83640A
• #3914: Report of MB emission tests contains a large list of detected peaks, if no peaks are detected
• #3915: Use a Microsoft SQL Server database to retrieve customer information
• #3916: External PM is not allowing the selection of modulation out side the dwell time
• #3919: Possibility to draw graphs via report generator with the full dataset

RadiMation version 5.8.12

• #3857: PMM 9030 driver is giving time out during measurement of peak
• #3877: Slow final measurement with PMM 9010/30P via RS232
• #3878: PMM 9010/30P hangs up in final measurement
• #3885: Peak and Average measurement at the same time with PMM not possible
• #3891: TSF does not save measure- and observation time from "optimize" - settings
• #3892: Wrong detector is used in final measurement
• #3899: Y-axis unit is not shown anymore in singleband emission manual mode
• #3900: Observation time of a singleband emission test is always 1 second
• #3901: Opening Multiband Emission tests is slower

RadiMation version 5.8.11

• #3308: Measure with ESVS10/ESHS10 with PK and AVG detectors together: average trace is not visible until the sweep is finished and the method is saved, closed and open again
• #3868: Creating new 16 point verification on a chinese pc is displaying a message box and not crashing
• #3888: Graphic of correction file not displayed
• #3889: RadiMation manual contains a lot of unrelated text
• #3890: High peaks in the emission graphs of the R&S ESHS

RadiMation version 5.8.10

• #3869: Saving a cor file is giving problems with ) at the end with a chinese pc
• #3882: CE Current probe test is crashing
• #3883: Multiband Emission graph is showing Bars
• #3913: list of detected peaks does not have all the Average values specified

RadiMation version 5.8.9

• #3791: Peak detection wrong in CE-MB (LISN) test
• #3843: Multiband emsion data file cannot be loaded anymore. It seems to be corrupt
• #3872: Reselecting the report is giving the .doc instead of .txt in the result file

RadiMation version 5.8.8

• #2915: Report generator template should be selectable in the file selection window
• #3757: Report Generator to ASCII

RadiMation version 5.8.7

• #457: Possibility to perform MIL-STD emission measurements in dBuA
• #469: Not possible to perform broadband measurements (dBuV/MHz)
• #475: Vertical scale of emission graph is not possible in dBuA
• #552: Configuration of the emission graph lines
• #784: Radiated emission graph dBuV should be dBuV/m
• #1300: Merge function - Scaling is wrong in Report Generator
• #1688: Sorting in unit configuration window is not working as expected
• #1704: IMaster unit transformer
• #1834: Possibility of measuring a magnetic field with a loop antenna (Unit dBµA/m)
• #2063: Changing the unit in a CE Current clamp test, doesn't change the graph
• #2205: Is fast scan mode supported in the multiband emission
• #2248: RE magnetic field MIL STD test reference value is always zero.
• #2274: Multiband Conducted Emission current probe
• #2327: RE multiband test can not be started from restart last test button
• #2413: Radiated emission substitution method test
• #2656: A multiband graphline is included multiple times on the graph
• #2966: Possibility to see the internal attenuation of a coupler device driver
• #3184: The unit of the reference level and the Emission is the same, so the correct reference level can not be reported
• #3381: Traces are not converted to the correct amplitude unit
• #3395: Limit lines hidden during pre-scan
• #3415: The sequence of the Multiband is according to the way it's been entered
• #3420: AdvantestTR4172 device driver is missing for input 1 50Hz - 1800MHz
• #3596: Limit Lines not shown during CE measurement in Multiband
• #3607: CE Multi band can only be performed with a LISN
• #3699: Possibility to set a default unit for radiated Emission and conducted Emission
• #3718: Limit line with unit
• #3719: Emission Test: Results are not converted to chosen unit - just the display is upgraded
• #3731: sx32w.dll is causing problems with the dongle in version 5.7.2
• #3784: RI multiband test is not turning on the amplifiers in version 5.7.4 while this was working in version 5.6.13
• #3830: Physical properties do not match with the units in the menus when using German language
• #3831: Support for the mil std dbuV/Mhz/M according to the 462C standard
• #3832: changing dbuV to dbuV/m does not change the reading in the display
• #3833: Narrow band / broad band detection according to the Mil std 462C standard
• #3835: Specification of the limit line in the configuration of the limit line
• #3844: dbuV/m/MHz axis is not displayed is not displayed in the mil std test
• #3845: BCI multiband is not displaying the lines correctly when the levels are identical
• #3852: Saving a file doesn't show a progress bar
• #3855: ESHS10 is scanning the frequency range 3 times
• #3856: Opening older (< 5.8) multi band lisn test is causing a crash
• #3859: AC coupling on input 1 decreases the start frequency of the ESU26.
• #3861: Communication Problem with configurable AD converter via TCP/IP

RadiMation version 5.8.6

• #3418: Driver: Advantest R3261A as powermeter
• #3604: RadiSwitch is generating sometimes is generating an error during the test.
• #3653: Driver: IFI 404
• #3656: Driver: OPHIR 5019E
• #3681: RadiMation tries to put FSP 3 in Receiver Mode
• #3803: CARAD - Timeout
• #3804: CARAD - debug window
• #3805: CARAD - clear buffer after timeout
• #3806: CARAD - error message when using wrong IP-address
• #3809: Not possible to configure stepsize in RE-MB RC test
• #3818: several questions regarding CAPL
• #3824: Configurable alarm detection is always reporting alarm, even when the correct response is returned.
• #3829: Driver for Amplifier Bonn BSA1050-250/100
• #3840: Copyright is 2009 instead of 2010
• #3841: Closed loop band before substitution band is checking the calibration information of the substitution band
• #3842: end-of-line character for AD Converter via TCP/IP
• #3846: Cannot select multiple cables for a specific part in a testsite
• #3849: Am modulation is not turned off when selecting no modulation in RI multiband test.

RadiMation version 5.8.5

• #2600: Undocumented error 0x300000C9 when Prana amplifier was already switched off
• #2775: Measurement of current by using the current sensor in combination with a multimeter or oscilloscope is wrong
• #3190: Driver: Anritsu MS2621B
• #3447: Conducted Immunity Tests are slow in 5.5.7 in comparison to 5.3.18
• #3636: Driver: Logimetrics AN8200G
• #3637: Driver: Logimetrics AN 8100Q
• #3651: Driver: Kalmus 122FC
• #3652: Driver: Kalmus LA200U
• #3732: Driver: Milmega Rf1000
• #3734: Driver: schwarzbeck antenna's FESP 5132 + FESP 5133-7/41
• #3735: Driver: SCHWARZBECK TEMZ 5231
• #3819: Network Analyser EUT Calibration, using a R&S ZVK, crashes with an overflow
• #3828: Unit is single band graph do not change after changing the unit in the unit configuration of the result file
• #3838: Why is it required to specify a magnetic flux density file for a MIL STD Calibration?
• #3839: Radiated Immunity MIL STD Calibration is always using a 70 dBuV Reference level

RadiMation version 5.8.4

• #1290: Radiated Immunity not completely usable for H-Field measurements
• #2604: Full support for Magnetic field tests in Radiated Immunity module
• #3095: RadiTurn controller does not allow a destination angle below 0 or above 360 degrees
• #3147: Memory leak in opening/closing RE MB TSF
• #3283: Modulation command is not retransmitted by configurable device driver if modulation parameter is changed
• #3686: AD Converter is read out before modulation is switched on
• #3720: During emission test: crosses instead of line
• #3779: Calculated field is not send to switch matrix in multiband test
• #3781: Driver: Farnell PSG 1000B
• #3789: Memory leak in reviewing Multiband Emission test
• #3802: Memory leakage in Multiband Emission test, when test is opened and closed
• #3823: TDS 600 Series scope driver reports unknown device driver when pressing advanced in the device driver settings window

RadiMation version 5.8.3

• #507: Overload indication of an analyser/receiver is not detected
• #2764: Optimize IDataIdentifier comparing
• #3183: Crash of RadiMation Version 5.3.18 when CARAD driver is included
• #3354: CARAD interface: two commands get combined to one
• #3372: ESU8 returned an error message during Radiated Emission MB measurement
• #3535: *OPC for ZVK with antenna measurement
• #3544: Device driver for Narda NBM550 uses the wrong baudrate
• #3615: Multiband-Conducted Immunity: data is not displayed
• #3780: Driver: Pre amplifier Schwarzbeck BBV 9718
• #3782: Driver: Antenna Schwarzbeck STLP 9128D and Elektromectrics EM 6954
• #3794: Driver for amplifier Bonn BLWA-0820-160/75/50D
• #3814: Driver: AR 15S1G4
• #3816: *OPC problems for ZVK (as signal generator) when setting the power level

RadiMation version 5.8.2

• #2152: Peak search for turntable angle should be configurable to include another angle range than the configured turntable
• #2153: Peak search for antenna tower height should be configurable to include another height range than the configured antennatower
• #2843: Incrementing the turntable angle, should wrap to the corresponding value if the maximum angle is reached
• #2849: When the turntable angle is changed, the direction with the shortest angle difference should be used to turn the turntable
• #3545: Automatic Angle and Height optimization should use the physical limitations of the turntable and antenna tower
• #3592: Turn Table Action in Manual Mode not possible with EMCO 1050
• #3593: Antenna Tower Action in Manual Mode not possible with EMCO 1050
• #3755: RadiMation is setting up the ESPI with incorrect RBW during CI-testing

RadiMation version 5.8.1

• #3201: Dificulties with OATS measurements
• #3563: Limit lines should be shown in polar plot and height graph
• #3701: Multiband Radiated Emission: Default value in dropdown list for Turntable Angle specifies 235°
• #3744: When 'Detect Peaks' is pressed, already detected peaks should be placed on the angle/height with the maximum emission
• #3745: Turntable doesn't turn a complete turn when it starts on a negative angle
• #3746: Peak zoom-in doesn't seem to work in multiband emission
• #3747: Improve peak detection by splitting the span in chunks
• #3748: Improve EMCO1060 turntable controller
• #3749: Click on the graph to add peak, should allow multiple peaks on the same frequency but with a different polarization
• #3751: Frequency marker is not moved on the graph when it is dragged
• #3752: Clicking on the turntable CW button to release it again doesn't respond
• #3753: HP4395A is always using 10 Hz RBW when it is used for a voltage measurement
• #3754: Climate chamber is not controlled correctly by RadiMation.

RadiMation version 5.8.0

• #1713: Continuous scanning is not possible in Multiband Emission Manual mode
• #2512: Zooming into emission graph while measurement still running
• #2597: In multiband immunity the cancel button only reacts on the end of the dwelltime
• #3203: Manual mast control does not work correctly, Up is not always Up
• #3386: the Radisense ctr1001B driver does not allow you to set the filter when using in gpib mode.
• #3490: Multi band emission manual mode is generating error when selecting the test site
• #3456: Manual mode multiband emission test does not have an initial graph which results in a crash
• #3547: First graph in a multiband emission measurements shows a bottom y-axis value of -1000 dBuV/m
• #3552: Spurious peaks in polar plot as a result of the initial measurement
• #3566: Change the frequency/angle/height of a detected peak by moving the marker in the graph
• #3611: Turning range of the antenna tower when changing polarization
• #3709: zero-span mode in radiated emission multiband
• #3714: Emission Multiband: Scan analysis while scan is running
• #3720: During emission test: crosses instead of line
• #3724: Radisense 4 over RS232 does not set the filter setting
• #3729: CE multi band measurement is not showing the information below 1 MHz
• #3736: I can not select apply modulation outside dwell time when selecting pulse