Release Notes/Solved items Version 2015.1

RadiMation version 2015.1.12

• #3821: Test equipment not correctly changed in radiated immunity multiband
• #5250: Change format of graph export per default
• #5402: Driver: AR 20ST1G18 Amplifier
• #5595: Driver R&S Vector Signal Generator SMBV100A
• #5596: Driver: AR 50ST1G18 amplifier
• #5670: How to integrate probe calibration values into RadiMation
• #5871: Metrohm Antenna Tower device driver
• #5892: Turning on modulation of R&S SME is having a hardware delay
• #6033: Extend driver for Agilent 34401A Multimeter (AD Converter) with VISA communication
• #6063: HP 4417A Power meter issue
• #6136: Driver Frankonia controller Model FC-06
• #6200: The AD Channel configuration window is not responsive when it is shown the first time
• #6202: Show the DeviceStream configuration of a device driver in a panel below a combobox
• #6208: Driver: IFR2398 Spectrum Analyser
• #6209: Configuration National Instruments AD converter for channel 9 and higher
• #6211: HI 6105 Device Driver Function Not Implemented
• #6212: HI 6105 wxDynamicLibrary already loaded error
• #6213: HI 6105 always tries to switch to local
• #6214: Driver Prana DP600 amplifier
• #6221: Driver Anritsu Spectrum Master MS2713E as field sensor for 2000-1791-R antenna
• #6222: How can we change the speed of the Maturo turntable
• #6224: Extend driver for Agilent 34401A AD Converter with VISA communication
• #6225: Driver Manual Controlled AD Converter
• #6226: No values for National Instruments AD converter channel 9 and higher
• #6232: How to measure the Frequency and duty cycle with Oscilloscope or AD Converter
• #6234: Directly raise an error when device is disconnected
• #6249: Wrong AD Channel is selected for RadiSense probe
• #6272: Driver of Keysight Technologies N9038A is checking for the 'Agilent Technologies' *IDN? response

RadiMation version 2015.1.11

• #1491: The directory selection is not showing the directory
• #2697: Possibility to use units during editing of correction files
• #5683: Driver EPI1001A CTR plugin card
• #5947: Modulation of Marconi 2024 Signal generator is never turned off during CI test
• #5971: Driver: Fluke45 as multimeter
• #6098: Logarithmic step frequency for R&S ESPC Receiver
• #6151: Advantest R4131D No match was found in the specified regular expression errors
• #6161: Graph Customization Configuration button Restore factory default is always disabled
• #6166: Verification TESEQ drivers
• #6169: RPR device driver is crashing RadiMation
• #6173: First sweeps Advantest TR4172 are jittering, causing wrong measurement results

RadiMation version 2015.1.10

• #3503: The configurable signal generator does not allow the setting of the external modulation settings
• #4410: Changed modulation settings are not applied
• #4831: Not possible to see actual values in table mode
• #5467: Hide all table information is not working
• #5782: ESRP raises an error for an unknown header: INP:GAIN:LNA:STAT OFF
• #5796: Setting the frequency is showing rounding issues
• #5915: Driver: Keithley Arbitary Generator 3390 as modulation source
• #5947: Modulation of Marconi 2024 Signal generator is never turned off during CI test
• #5960: Pulse modulation settings in the singleband fixed power manual mode window are not forwarded to the signal generator device driver
• #6054: Cross thread operation detected error
• #6057: Keyword ||RADIMATION VERSION|| is exporting 201x,x instead of 201x.x.x
• #6061: Can not save LLF anymore after making changes
• #6065: Multiband PM Modulation Configuration setting is not retained
• #6066: Windows Universal Naming Convention (UNC) is causing error "Access to the path.. is denied." when creating a new TSF directory
• #6078: Opening a test in a newer version overwrite test data used RadiMation version
• #6085: Support 2 Hz AM modulation in RadiGen
• #6095: Driver Bonn BTA 0122-3000
• #6099: RadiCentre is still in remote after deinitialisation
• #6102: Overshoot detection of the EMCO1060 is not working
• #6103: Suggested product id number for instrument descriptor of NRP power meters is wrong
• #6107: R&S BBA100 RF path is not being switched between bands
• #6111: R&S AFG device check seems to be always successful
• #6112: R&S BBA100 RF option to always keep amplifier on
• #6113: External Modulation Source settings are lost
• #6114: Configurable Signal Generator Modulation settings are not retained
• #6115: Enable wxWS_EX_VALIDATE_RECURSIVELY for all device drivers
• #6116: Move during measurement should not be visible in an immunity multiband test
• #6120: Configurable Modulation Source carrier level is not send
• #6171: CARAD EUT Controller driver settings are not retained

RadiMation version 2015.1.9

• #4140: Problem with ESL6 and conducted emission LISN test
• #5140: Current Status windows without a description is shown
• #5230: Not possible to delete measurement data from the EUT
• #5325: R&S ESIB26 Analyser not all bytes are writen (..) within the timeout period
• #5526: Implement Word Wrap for error code descriptions
• #5889: CDN test according EN61000-4-6
• #5891: Driver National Instruments AD converter (NI USB 6218 BNC)
• #5929: Monitoring input channel setup is not using the correct default device driver setting
• #5943: AR No Listeners are detected on the GPIB bus and the KRE matrixes is alway switching to position 2
• #6060: Quasi peak measurement of Advantest TR4172 sometimes has a difference
• #6067: Agilent N9038A MXE is not using Discrete Scan Type
• #6072: Driver Narda SRM3006
• #6082: Typo in the description "successfull"
• #6083: Adding beeb as before or after action is directly showing a warning
• #6084: Driver AR 100S1G6 amplifier
• #6091: How to manually operate an Antenna Tower and Turn Table
• #6097: How to perform a CE measurement with a voltage probe (PMM SHC-1-1000)

RadiMation version 2015.1.8

• #5052: Reference level is changed during measurement, generating an IF overload
• #5385: Power delivery test stops with “Power went to high -4dBm Signal Power"
• #5829: Frequencies labels are not correctly updated in a Mutiband TSF
• #5950: Driver Amplifier Bonn BSA 0106
• #5976: Saving a Pause Test is generating several 'file corrupt' problems
• #5983: Driver for obsolete field probe PMM8052
• #5998: What means: 'before', 'during' and 'after' on the EUT Monitoring channel
• #6002: Do not change the reference level. Leave it fixed on the selected level
• #6030: AR FP 3000A Field sensor is not connected
• #6034: New EUT Monitoring channel configuration is not working in Singleband immunity
• #6035: Values specified in the Min and Max of AD Input Range are lost
• #6037: Driver National Instruments Switch (NI USB 6218 BNC)
• #6038: Driver HP 83650A Signal generator
• #6039: Driver FSP 40 as powermeter
• #6040: Driver CBL 6112C
• #6043: Units configuration is not applied to test
• #6045: Auto save function after completion of (Multiband) tests is polluting the EUT
• #6051: Possibility to send switch command before power on for the Configurable Amplifier device driver
• #6052: Configurable amplifier device driver is sending the standby command at start of test and operate command after the test
• #6056: Monitoring input channels from channel 33 and higher are not working
• #6079: Problems with Software Protection Key dongle
• #6089: No graph or table information is exported in manual mode test data
• #6092: Different antenna polarization errors during UFA calculation

RadiMation version 2015.1.7

• #2140: Ampersand in name of test-site is shown as underscore on information window
• #5634: R&S ESPI 7 specific system error SWE:SPAC LIN
• #5856: Auto move of antenna tower is harmfull for hardware
• #5904: Keyword TEST TIME is exporting wrong data and shows TEST START TIME
• #5906: Spurious emissions with high values are detected during noise floor measurement
• #5910: Sunol SC110V customer specific Antenna Tower driver
• #5917: Final peak measurement with ESR 7 blocks the software
• #5925: Configurable Signal Generator is missing the Remote Control checkbox
• #5939: Strange measurements with the R&S ESVS20 Test Receiver
• #5940: HP 33120 signal generator raises error 1 -113
• #5946: Driver AR 40S4G18M4 Amplifier
• #5961: A 1 hour multiband immunity test causes an algorithmic calculation error
• #5964: R&S ESR7 Specific System Error -141 Invalid character data SWE:SPAC APUL
• #5970: RSS1006A no connection after changing COM port
• #5980: The entry "Configurable EUT Controller" is in the driver list of Switch Matrix and not in the list of "EUT Controllers"
• #5986: Frequency up/down is not working in multiband immunity manual mode
• #5987: Driver Milmega AS0827-55 amplifier for IEC61000-4-3
• #6014: Power delivery test is not succesfull at 550 MHz
• #6044: How can I get more precision from the data of a calibration file?
• #6074: Forward power measurements values are showing dips

RadiMation version 2015.1.6

• #4598: Driver PMM9010F
• #4947: Diagram description in dBuA/m with Magnetic field setting
• #5155: Driver PMM9010F
• #5369: RadiMation crashes when SRQ line is busy
• #5594: Driver Agilent Power Meters U2000H, U2000B and U2002A
• #5641: Signal power went to high errors with Gigatronic 8542C powermeter
• #5645: Peak measurements give different results
• #5841: MXE receiver N9038 is not starting performing the measurement
• #5843: First point of forward powermeter (Advantest analyser) measurement is wrong
• #5844: Advantest analyser as powermeter is not automatically switching the attenuator
• #5847: RadiField field verification
• #5883: ESL 6 quasi-peak measurement gets stuck
• #5907: Error detected during the start of the sweep with PMM 9010 F
• #5919: Unexpected power readings with RPR3006W Powermeter
• #5932: RIGOL DSA 815 AVG and QP measurements are showing differences compared to manual measurements
• #5933: Regulation in the Multiband Immunity test is not increasing the power to satisfy both Testlevels
• #5937: Driver: Rigol DSG3060
• #5945: RIGOL DSA 815 timeout and query interrupted
• #5948: When opening test data a Run-time error '91' Object variable or With block variable not set is shown
• #5949: Driver AR Field Analyser 7006 read out
• #5951: RadiMation crash during startup
• #5955: Drivers AR DC2500AM1, DC7128A, DC7420M1, DC7530 and DC 7620
• #5957: Driver AR 40T26G40A
• #5958: Drivers Antennas ATEK30MM1, ATL80M1G, ATH18G27, ATH26G40
• #5965: What is the difference between the average value and the measurement value of the used field probe?
• #5966: Why is the setting of the frequency range missing in the driver window?
• #5972: When is the CAL calibration file needed to be used
• #5979: What is the External Dwell Time and how is it working?

RadiMation version 2015.1.5

• #3864: Init of the multiband test is not using the amplifier driver of the amplifier manager
• #5590: Include option to download latest drivers.exe in RadiMation setup program
• #5602: Include option to overrule drivers.exe included in RadiMation setup program
• #5826: Error 76: Could not find a part of the path (..)
• #5828: Opening a TSF file from a sequence is suddenly changing focus at the sequence window again
• #5830: Test file is corrupted after opening and saving
• #5831: Unexpected forward- and sensor power measurements during calibration
• #5896: Showing graph and table information is making the performed test extremely slow
• #5909: Configuration of Narrow band / broad band detection according to standards has disappeared
• #5922: Update Copyright information of device drivers setup
• #5928: Current Closed loop method is not correctly controlling/reading the sensor power meter
• #5931: Data files of a RI Multiband test are corrupted after editing the note
• #5959: Driver: Narda PMM EP408 Field probe

RadiMation version 2015.1.4

• #2249: Not possible to set limit line from 500 Hz to 900 Hz
• #4019: Unexpected CIC errors
• #4733: No trace of the measurement data visible
• #4748: QP measurements seems to be wrong
• #5406: Peaks are detected outside the graph trace
• #5563: Continuously measuring envelope power of the RadiPower results in memory problems
• #5684: Unexpected high noise floor with CXA 9000A
• #5818: Driver for R&S ESPC not working anymore after updating drivers.exe
• #5821: VI Powermeter: Burst Graph doesn't show the graph by default
• #5823: Driver: Teseq NSG 4070 as Amplifier and Powermeters
• #5826: Error 76: Could not find a part of the path (..)
• #5827: TSF files can't be deleted, delete and Ok buttons are always disabled
• #5837: How can the field sensor be corrected by a RadiMation file?
• #5846: R&S ESRP error Data out of range during time setting
• #5848: Does the modulation needs to be turned off and on during each frequency step?
• #5849: How can a customized warning message be shown?
• #5857: GPIB Hibernated NI Drivers error required PC restart and loss of data
• #5860: Frequency range of Agilent N5171B Signal Generator
• #5862: How to add the correction for the emission antenna VW TL81000?
• #5868: RadiMation is crashing when device is not connected

RadiMation version 2015.1.3

• #5642: Driver Teseq NSG 4070 as Signal Generator
• #5736: No trace data obtained from measurements with FSV13
• #5739: Cursor information is no longer shown
• #5778: Rigol spectrum analyser as powermeter is using pre-amp
• #5780: Control of the Maturo antenna tower is not working if it is controlled with a LAN-to-GPIB convertor
• #5790: Final measurement of QP detector on R&S ESI always returns 0 dBuV
• #5797: R&S SME03 Specific system errors Level over range and ALC failure
• #5800: Windows XP is not supported anymore
• #5801: Detection if zeroing of RadiSense4 probe is finished takes a long time
• #5803: Controls of the VI Powermeter are not reenabled if the auto-trigger is disabled during the re-trigger wait time
• #5805: Old test results cannot be loaded in 2015.1.2
• #5816: Rigol spectrum analyser pre-amp settings can't be controlled

RadiMation version 2015.1.2

• #5787: Selection of another TSF folder doesn't update the list of TSF's in that folder
• #5791: Uniform Field Area Calculation is not working for Constant Power method calibration files

RadiMation version 2015.1.1

• #5775: Driver R&S switch matrix for amplifier BBA100 interlocks