Release Notes/Solved items Version 2016.1

RadiMation version 2016.1.13

• #3168: Is amplifier protection working in a multiband immunity test
• #3517: Radiated Immunity: Level is going too high
• #4397: Forward power protection file for an Amplifier is ignored if power is already limited
• #4586: Amplifier limit completely ignored
• #6304: Reference level should be requested to ensure a correct calculation of the measurement value
• #6855: Limitation of a Multiband Immunity test on the current is levelling just above the limit
• #7437: R&S FSEK 30: Function not available;BAND:MODE:FFT OFF
• #7468: Quasi peak measurement of Analyser sometimes has a difference
• #7634: R&S FSEK 30: Function not available: FFT OFF
• #7786: Regular expression of RFS2006B antenna tower is incorrect
• #7787: Driver Vectawave VBA230-22 and VBA1000-150
• #7789: Advantest TR4172 Not all bytes are written to the GPIB-Board within the timeout period

RadiMation version 2016.1.12

• #1784: Agilent E4416A/E4417A (EPM-P series) should have option to measure Peak power
• #4397: Forward power protection file for an Amplifier is ignored if power is already limited
• #5629: Include option to 'Run Radimat.exe' after Device Drivers setup program
• #7080: Driver: EM test CWS 500N2.2
• #7099: Changing Powermeter advanced Measure setting is not enabling other settings when only the value is changed
• #7301: Driver Messtechnik Motion detection system
• #7475: Extend Field sensor device driver configuration with advanced Monitoring measurement settings
• #7476: Wrong measurements at first frequency point of the test
• #7615: Does the driver of the Power meter E4417E performs reading of the peak value?
• #7641: Measurements take a long time with the Advanced ESU 40 / FSV as a powermeter
• #7650: Voltage test level Voltage measurement (Powermeter) is not measured
• #7659: Agilent N5182A error the measurement device does not support this functionality
• #7666: Driver R&S EZ17 current probe
• #7668: Driver: Schaffner/TESEQ CDN S150
• #7669: Driver Schaffner/TESEQ CDN USB/p
• #7672: Driver: MEB CDN S25
• #7673: Driver: MEB CDN S1/50
• #7674: Driver MEB CDN MEB KEMZ801
• #7676: Driver: Switch matrix HP3488A
• #7677: Driver: NRP8SN
• #7678: Driver: Directional Coupler RFPA RFC801000 -40-150
• #7679: Driver: Directional Coupler RLC CHP-1040-D-40-40-FF
• #7681: Driver CDN Schaffner USB/c
• #7683: Driver CDN Teseq M116
• #7684: Driver: NRP8 Power meter
• #7698: EM Powermeter unable to pass the checkdevice.
• #7702: Driver: ETS-Lindgren's 8100-045 RF Power Amplifier
• #7703: Driver: Werlatone C10762 Coupler
• #7704: How to use a manual Turn Table during Multiband Emission?
• #7709: Sensata Olimex SENT (Configurable AD Converter) Timeout before operation completed
• #7710: Spectrum Analyser (ID1465) Input 2 (LAN): SPecific System Error: -410, "Query interrupted"
• #7730: False graph of result of N9000-series measurement: High emissions
• #7739: Agilent E4417A Not all bytes are written to the GPIB-Board within the timeout period (GPIB: EABO)
• #7747: EMTest UCS500N + Phase 3 coupler Error
• #7749: SetEndOfString is not used
• #7762: Ability to use the Configurable AD Converter for PMX
• #7771: R&S ESI as powermeter is measuring too fast
• #7772: The measure time is not always correctly set when the receiver is used as a powermeter
• #7774: Correction of resistor is not used in magnetic field measurement

RadiMation version 2016.1.11

• #4272: Wrong values tuned frequency range HP85685A Preselector
• #7008: Reflected power too high
• #7082: CE test 20V problem
• #7279: End of Surge test is not correctly detected on a Teseq NSG3040
• #7461: Unable to use formula option in AD converter
• #7485: Driver Signal Generator Keysight 33522B
• #7515: SRQ errors are generated using Tektronix TDS5034B
• #7542: Driver Amplifier IFI S41-250
• #7624: Driver Keysight Amplifier N4985A
• #7631: Agilent Technologies N9038A Scanning Receiver: Device is not aligned error
• #7638: Maximum selectable RBW for the Analyser As Powermeter settings is 50 kHz
• #7642: Agilent N9038A set RBW raised error Data out of range; the value 0 was clipped to the minimum value of 10
• #7651: Wrong frequency range Teseq CBA 1G-1000
• #7654: Configurable Amplifier custom frequency range is not retained
• #7693: Device driver configuration of the RSS1006A (CTR1001S) field sensor
• #7699: Re-enabling the selectioning of peak markings
• #7763: How to launch programs?

RadiMation version 2016.1.10

• #2533: Power conservation is not clearly described in the user-manual
• #3917: Nonexistent peak and wrong final measurement with PMM during conducted emission multiband tests
• #4550: Driver: EM-Test Signal generator CWS 500
• #4596: Problem with PMM in latest version
• #4821: Driver Tektronix 3000 for fixed voltage test
• #5989: Driver: emtest CWS500N for IEC61000-4-6
• #6328: Driver FSV-3 as powermeter
• #6383: Error -222 Data out of range;INP:ATT 50 DB while deinitializing a R&S ESL 6
• #6767: Too much reflected power in combination with the RadiField
• #6955: Error too much reflected power due to RadiField reflected power value
• #7030: Driver: CWS500N2 EMTEST
• #7080: Driver: EM test CWS 500N2.2
• #7107: Incorrect LimitLine values
• #7232: R&S ESI26: Data out of range: 1 Hz RBW during powermeasurement
• #7323: Prana MT400 Not all bytes are written to the GPIB-Board within the timeout period
• #7324: Prana MT400 Amplifier still in operate
• #7325: Prana MT400 Amplifier not always to RF-ON
• #7446: Reflected powermeter measurements data is incorrectly shown
• #7463: Test duration takes a lot of time as compared with a old software used before
• #7505: Frankonia FC 06 Turntable Error -33072 (Invalid target position)
• #7508: End frequency is not correctly stored in an attenuation/gain system calibration
• #7524: Driver NOVOTRONIK GTS5611 switch matrix
• #7525: Driver NOVOTRONIK GTS5601 switch matrix
• #7530: Selecting 'AD converter selected in testsite' as monitoring input device is default selecting 'nothing' instead of channel 1 resulting that nothing will be measured
• #7553: How to configure default graph log or linear scaling?
• #7554: Driver Advanced settings for ESU 40 as a powermeter
• #7592: RadiMation does not trigger a GetCurrentStatus after Operate and PowerOff
• #7599: Driver: AR FL7218 Field Probe
• #7601: RadiPower RPR2006 powermeter Windows device drivers
• #7601: RadiPower RPR2006 powermeter Windows device drivers
• #7602: Bonn Testsystem
• #7605: GPIB-Board is not controller in charge (CIC) GPIB: ECIC
• #7607: Shifted Report Generator table
• #7615: Does the driver of the Power meter E4417E performs reading of the peak value?
• #7620: PI EFT singleband Report generator codes empty
• #7648: Missing keywords for EUT calibration Harmonics
• #7686: Wrong title above emission plots
• #7687: Progress bar in PI MB tests is not visible after second sequence

RadiMation version 2016.1.9

• #1828: Additional total max hold graph window
• #1957: Wrong message when no impedance file is selected
• #3001: Manual is missing information on how the corrections (and the to be used columns) should be used
• #3444: LISN ESU User port lan device
• #4975: Sorting of table frequency data in the Report is incorrect
• #5815: Driver Agilent N1911A powermeter
• #5863: Error File is not found: %s when opening TSF or after crash
• #5994: Test initialization failed for Agilent N5181A-506 with Pulse Modulation option
• #6177: CARAD EUT Controller driver raises Ethernet not connected errors
• #6420: Exported RAW data is still showing unit information
• #6752: The Device Specific value 'Power' of the powermeter should be renamed to 'Uncorrected Power'
• #6902: Keywords TEST SITE EMAIL ADDRESS and CLIENT EMAIL ADDRESS are not working anymore
• #6933: Driver Luthi MDS 20 Absorbing Clamp
• #6934: Driver EMCO 3158 Antenna
• #6935: Driver CBL 6144 antenna
• #6936: Driver ARA DRG 118a Antenna
• #6944: Driver Holaday HI4422 FieldProbe
• #6951: Driver Schaffner NSG 2070
• #6961: Description for this error is not available is shown during startup
• #6964: Ability to have Start and Stop Dwelltime events for the NI 6218 switch matrix
• #6993: RadiGen RGN6000B Setting the output level raised an error
• #7010: Use a NI USB6501 to switch between forward and reflected power
• #7024: Problem solving for the test setup of a Conducted Immunity Mil Std Calibration
• #7025: Driver Rohde & Schwarz ESW26
• #7040: Marconi signal generator doesn't respond on *STB?
• #7197: Driver Generic National Instruments Output Switch
• #7275: Switching matrix OSP 120. Relay K11 on slot 3 doesn't switch
• #7291: RadiGen RGN6000B HF Returns error: -222 Data out of range
• #7298: TCPIP Communication is not working correctly for the TDEMI
• #7304: TCPIP controlled TDEMI Powermeter raises a crossthread error message
• #7311: Driver Aaronia Spectran HF-60100 V4 X
• #7314: Insert additional frequencies
• #7340: Driver AE Techron 7224
• #7341: Driver OSR C21A8
• #7342: Driver TESEQ CIP 8136
• #7343: Driver Rohde & Schwarz ESW8
• #7345: Driver Agilent 87405A pre-amplifier
• #7346: Driver Agilent 34401A
• #7348: Driver Agilent 54831B as oscilloscope
• #7349: Driver Agilent 34401A
• #7352: Driver Antenna Schwarzbeck BBHA 9120J
• #7353: Driver Antenna Schwarzbeck STLP 9128ES
• #7354: Driver Directional Coupler werlatone C7354
• #7356: Driver AR 500W1000B
• #7379: R&S NRP only channel a is working
• #7381: R&S ESL6: Several GPIB communication problems
• #7397: RadiField RFS1006B Returns Error 521. Driver 3 current out of range
• #7403: Communication with plugin cards is lost
• #7424: Keysight N9083A runs incredibly slow after 3.6 GHz in scanned receiver mode
• #7433: Not all data is recorded in RE GTEM
• #7461: Unable to use formula option in AD converter
• #7466: RadiField RFS1006B Returns Error 560. Communication amplifiers failed
• #7478: EFT/Surge and VDI Report Generator keywords overview
• #7480: Question regarding R&S IMS device drivers
• #7483: Update the RadiMation software requirements
• #7486: RSW1024S Interlock: Not all bytes are written to the GPIB-Boadr within the timeout period
• #7487: RadiField RFS1006B Returns Error 526. time out error GPIB
• #7488: RadiField RFS1006B Returns Error 1087. Signal power went to high (-6dB) during power delivery test
• #7493: RadiField RFS1006B Disconnecting error: No amplifier connected
• #7494: Kalmus amplifiers cannot be controlled. GPIB: No listener on the bus
• #7495: RadiField RFS1006B Power off after disconnecting device
• #7502: Extend the IDocument interface to also return an unique IDataIdentifier
• #7503: Change the implementation of IGraphElement::DataIdentifier to also use the IDataIdentifier of the data document as the parent IDataIdentifier
• #7504: List of available graphs should use the IDataIdentifier of the graph element
• #7508: End frequency is not correctly stored in an attenuation/gain system calibration
• #7510: SetMicroSecondsDelay is ignored/not used when set from the 'AfterStreamConnectConfiguration'
• #7516: NI DAQ Error 6009 Unable to keep up with the hardware acquisition
• #7521: How can the complete graph data of the polar plot be exported as table data?
• #7534: SMR40 driver slowed down in communication
• #7538: How to disable the power delivery test?
• #7539: Driver Antenna BBA 9106
• #7541: Driver PowerSensor Agilent N1911A
• #7543: Driver Antenna SBA 9113
• #7547: The used and installed version of the NI GPIB Library should be logged in RadiLog
• #7548: Setting the VISA communication setting to the Visa-ID is automatically being changed to RS-232
• #7550: Driver Broadband Preamplifier Schwarzbeck BBV 9743
• #7556: Extend the license that the user agrees that RadiLog and other reported gathered data being send might contain confidential content
• #7558: Driver Keysight EXG N5173B signal generator
• #7562: Driver SG6000 Signal Generator
• #7564: Driver Measuring amplifier B&K 2636 Analog, 1 channel (via GPIB now)
• #7570: Driver Directional Coupler Warlatone C9475
• #7571: Driver Teseq CDN M016S
• #7572: Driver Teseq CDN S501AS
• #7573: Driver CDN S751AS
• #7574: Driver Werlatone C5982 Dual Directional Coupler
• #7577: Easy merge of multiple EUT Attenuation/Gain corrections to one correction
• #7583: ETS-Lindgren HI-6053 error No match was found in the specified regular expression
• #7584: Driver Generic NI DAQ mx AD Converter device driver
• #7587: How to configure a limitation on power during a DO-160G/ED-14G BCI test?

RadiMation version 2016.1.8

• #4514: Support the +10 dBm output of the RadiGen
• #5705: Device driver Baudrate and terminator character settings are not used
• #6427: Please include in the manual that the graph trace description is a valid Report Generator keyword
• #6800: Exported AD Limit does not have the same color in the report
• #6970: Problems and overrange detected during CI Calibration
• #7101: Pulsed Immunity ESD is not removing selected tab
• #7195: Driver Amplifier VBA1000-275
• #7248: Testing a frequency above 1 GHz takes much more time than the configured dwelltime
• #7313: Reopening test files gives error: Object variable or With block variable not set
• #7426: Reflected powermeter is required when performing a Multiband fixed power test at Forward powermeter level
• #7450: Example of an emission measurement
• #7451: RadiLog search function does not always match
• #7460: RS232 communication settings are not updated
• #7469: Logarithmic step measurement using the R&S ESCS causes a crash
• #7491: Measurement with N9038A stops at 400 MHz.
• #7517: R&S ESCS 30: Not all bytes are written to the GPIB-BOARD GPIB:EABO
• #7531: Configurable AD Converter is using input range min max as multiplier
• #7546: Some PC's suddenly raise NI GPIB hibernation errors. A PC restart is then needed
• #7552: TCPIP controlled EUT monitoring of an Amplifier

RadiMation version 2016.1.7

• #4026: 10dB Min Attenuation is not switched OFF with the TDEMI
• #4030: TDEMI controlled LISNs
• #4674: Device driver system is currently not usable
• #4828: Guide how to configure and use RG templates
• #5600: RadiMation crash after Gauss TDEMI device driver check
• #5886: Driver R&S SMR20 Signal Generator (with internal pulse modulation)
• #6252: GAUSS Instruments TDEMI device firmware update now causes a timeout error after reset
• #6382: EM TEST UCS 500 Surge generators not possible to configure the GPIB address
• #6622: Driver: Different models for the Gaus Instruments TDEMI
• #6630: Add RadiLog messages to the DeviceDriverBase class
• #6647: RadiSense 6 fieldprobe connected by Radicentre 1 is raising an error
• #6791: Driver RadiField 2000 series as EM Field generators
• #6893: Add events when starting tests
• #6910: Driver: TDEMI X6 Spectrum Analyser
• #7037: Aplying modulation out of dwell time period gives odd peaks
• #7038: Disabled modulation at frequency steps
• #7063: Driver: Gauss TDEMI X
• #7110: Closing of the virtual Field sensor measurement window
• #7118: EM-Power 7002-006 powermeter Windows device drivers are not working
• #7137: Does Minimum performance take the minimum and maximum of every AD channel into account?
• #7181: Driver: euro EMC RSC
• #7184: Timeout on checkdevice TDEMI X3
• #7196: Driver: Amplifier Teseq CBA 3g-050
• #7209: emtest PFS500 SRQ line of the GPIB bus is raised by another uncontrolled device.
• #7224: AD convertor device trough MODBUS
• #7225: AD Convertor using OPC to connected with CAN USB convertor of PEAK with CANopen protocol
• #7290: RadiField RFS1006B Returns error: 574
• #7296: Cant add the HP8594E as real power meter to the EUT file after installing the latest drivers
• #7297: Check of a TDEMI is crashing if the device is not connected
• #7300: Driver Schwarzbeck NNBM 8126G seems to not work properly
• #7303: RadiField amplifier is not put into operate
• #7319: Driver: emtest CWS500N1.3
• #7336: EMTest EFT500
• #7379: R&S NRP only channel a is working
• #7382: Does RadiMation software use "Dwell for Combination of RF Immunity CW,AM,PM"
• #7385: Driver: EMTest TSS 500
• #7390: Connect button on the VI Amplifier window is not shown
• #7392: Selecting a VI from the Devices menu shows a new VI window, even if the VI is already open
• #7394: Update of the table of a graph, sets the selection to the first row again
• #7402: RadiPower RPR3006W questions
• #7405: Request Radimation driver for Rohde & Schwarz FSW-26 Signal Ananlyzer
• #7409: Software Protection Key could not be found
• #7447: Field Sensor FP5080 is returned unexpected values

RadiMation version 2016.1.6

• #4760: First band data seems to be lost with 10kHz tot 30 MHz Multiband test
• #5864: Preamplifier and reference setting have no effect for the ESL6
• #6086: Driver for the Delphin Technology Expert Key 100 box
• #6259: ALL RADIATED EMISSION TESTS is not replacing keywords of corresponding tests
• #6279: Readout of RadiPower in RadiMation Free raises overload at 0 dBm
• #6663: Provide same functionality as RadiMon
• #6687: Driver: Luthi MDS22
• #6708: No graph traces in the exported plots in the report for lower frequencies
• #6766: Measuring settings Lines/Neutral with LISN
• #6882: System requirements for RadiMation
• #6883: Using radiated immunity for shielding effectiveness
• #6915: Driver: Schwarzbeck BBA 9106 antenna
• #6916: Driver: Schwarzbeck MDS21 Absorbing clamp
• #6922: Driver: Teseq CBA 230M-80 amplifier
• #6923: Driver: Teseq PMU6003 Powermeter
• #6924: Driver: TESEQ DCP 0100A Directional Coupler
• #6925: Driver: Teseq KEMZ 801 Injection Clamp
• #6926: Driver: Prana MT440DC Amplifier
• #6927: Driver: Teseq NSG437 ESD generator
• #6941: Driver: Rohde & Schwarz NRVS
• #7006: Question: SMB 100A SignalGenerator modulation
• #7048: Selection of 'Neutral' LISN line is wrong when restarting last TSF
• #7062: Unexpected dips in measurements when rechecking peaks
• #7129: Corrupt Customized.xml will raise an error and crash RadiMation
• #7211: VDI Object reference error
• #7229: HP 8594E Spectrum analyser is not following signal generator.
• #7237: Report Generator graph only shows peak markers without the trace itself.
• #7243: Probe numbers are not shown anymore in the Field inputs dialog
• #7273: Behaviour of the ||EUT|DESCRIPTION|| Report Generator keyword
• #7280: Tabs of Device specific settings on the devices Virtual Instrument window are not shown
• #7282: Driver: Schaffner NSG 3025 BurstGenerator
• #7286: Vectawave amplifier is in endless loop, when an error is present
• #7317: RE MB build in preamplifier used at higher allowed frequency
• #7339: Driver: Agilent E4412
• #7350: Driver: AR 500W1000B
• #7359: Is the standard Din-EN 61000-4-6 supported through subsitution method?
• #7377: Clear button should be pressed automatically when the VI window is closed
• #7414: Device not connected errors for the PMM 7010 Low Input and Hi Input drivers
• #7430: No communication (device not connected) with Field Sensor FP5080
• #7431: RFS is not working and keeps powering off
• #7446: Reflected powermeter measurements data is incorrectly shown
• #7626: Final measurement of Average detector is lower than the average value of the prescan
• #7632: Not all emission tests are performed of the configured bands

RadiMation version 2016.1.5

• #5344: ESPI -222 Data out of range error
• #5434: Driver: Agilent N9038A, 44 GHz option
• #5480: Throw error or warning when 'Step Size clipped to nearest value allowed' for Agilent MXE N9038
• #5694: Driver Amplifiers Ophir 5225E / 5264E / 5274E
• #5786: Possibility to specify the 'auto-switch off' time of the PMM EP600-series probe
• #5956: Units change from dBm to W in the Power Meter Module does only change unit text
• #6273: Logarithmic step frequency for the Agilent N9038A
• #6310: Reference level of the N9038A is not set to the specified reference level in the TSF
• #6458: Several improvements and issues for the Agilent MXE EMI Receiver N9038A
• #6682: Driver Schwarzbeck MDS21
• #6683: Driver Schwarzbeck MDS22
• #6684: Driver Schwarzbeck LISN's
• #6685: Driver: Schwarzbeck VULB 9162
• #6688: Driver: Bonn Elektronik amplifier BSA 0125-25
• #6689: Driver Bonn Elektronik BSA series amplifiers
• #6718: Numbers on Analog scale of Virtual instrument should be updated when unit is changed
• #6792: Agilent N9038A: Non EMI average detector is change due to physcial constraints
• #6921: Driver: Agilent N5171B-506 + UNT
• #6940: Driver Bonn BSA 0122-20
• #7092: Longer time till sleep mode Narda EP600/EP601
• #7163: Errors connecting Lutron field probe
• #7170: Actual RH values no longer visible.
• #7173: Searching for possibility to download latest RadiMation version for driver release
• #7175: Wrong commands for Maturo ncd for antenna and turntable
• #7185: Unable to install the newest version, only HTTP and FTP are supported
• #7188: Advantest TR4172 No match was found in the specified regular expression
• #7194: Driver: Antenna Tower Inn-co GmbH MA4000
• #7208: Checksum error with the EMTEST CWS500N1.2
• #7217: Unexpected response from the Narda EP600 after filter setting command
• #7220: Driver: Vectawave VBA1000-1000
• #7238: Report generator text unexpected in bold.
• #7241: Sending an error report takes a long time (roughly 1 minute)
• #7246: Forward power and signal power graphs are not shown anymore in already performed tests
• #7302: Re-measuring peak values increases the measurement with 10 dB

RadiMation version 2016.1.4

• #423: Configuration of customer database is not retained
• #4809: Driver: Hameg HMS3010 Spectrum Analyser
• #5211: Driver: Maturo NCD controller advanced error checking
• #5228: HP8594E GPIB error
• #5314: RadiMation database table and fields are sometimes not retained
• #5492: System error checking on HP 8562/8563 causes communication errors
• #5969: R&S ESU EMI receiver is only set to integer frequency values
• #6175: Driver: Thermo Scientific EMCPro-PLUS
• #6429: Peak Maximise settings change doesn't work
• #6795: Graphs and table overviews are mixed-up and not correctly displayed
• #6810: Driver: Lutron EMF-819 Fieldsensor
• #6839: Forward power column in the table of Amplifier linearity is not showing the first powerlevel
• #6871: Driver: Hameg HM8135
• #6902: Keywords TEST SITE EMAIL ADDRESS and CLIENT EMAIL ADDRESS are not working anymore
• #6957: Not possible to export a fixed field to a CAL file, errors is shown that modulation was used is shown while this is not the case
• #7004: Pasting large data (19000 rows) into a COR file is crashing RadiMation
• #7032: GPIB communication is slower with newer drivers
• #7033: Unknown error message RadiField. Error 530
• #7040: Marconi signal generator doesn't respond on *STB?
• #7045: Cannot find Modulation source in the currently active testsite
• #7052: Crash: CE MB Antenna Terminal measurements
• #7056: 1st correction file selection of antenna shows: 'Select a correction file'
• #7057: HP 8594E analyser as a power meter returns Not all bytes are written to the GPIB-Board
• #7061: Graphs and table of Amplifier linearity test is unlogical
• #7075: sorting of columns of the peak table is not working correctly
• #7076: Exporting field strength to calibration is not working, because a modulation is selected, even if 'No Modulation' is selected
• #7084: HP85xx-series: Incorrect measurement: Emission values up to 330 dBuV/m
• #7086: Setup downloads .NET 4.6 instead of .NET 4.6.1
• #7094: Bonn amplifier should be placed in REMOTE, also on GPIB
• #7105: Unlogical Red cross in AD Configuration dialog
• #7108: Selection of CapacitiveClamp on EMTest UCS500N not correct
• #7113: Polar graph is not drawn correctly, when the window has been maximized
• #7117: Driver TTi TGR2050 Synthesised RF Generator
• #7119: RadiMation does not start up after modifying global/standalone directory
• #7124: Object reference not set to an instance of an object: Frequency drawing of bands control
• #7127: Font of the legend on the polar plot is much smaller than on the frequency graph
• #7128: Index was outside the bounds of the array error 536879965
• #7136: Unable to report error manually
• #7138: Issue with our home made 40 channel AD Converter
• #7141: AD Converter error during test initialization
• #7145: Output of multiple channels using LeCroy WaveSurfer Channel switch matrix driver during single band test

RadiMation version 2016.1.3

• #6311: Crash when maximizing the MB Emission test result window
• #6333: RadiMation crashes when maximizing the multi-band emissions results screen
• #6430: Radimation crash if radiated emission window resized during measurement
• #6686: Driver Luthi FT/FTC series absorbing clamps
• #6715: Run-time error 5 procedure call or argument is not valid in RADRESRC.DLL
• #6896: Error timeout with Maturo MCU controller
• #7017: SYST:ERR -222:Data out of range for RadiGen
• #7020: Limit lines are not shown automatically at the end of the test
• #7022: Maximum cable length is not included in the ||EUT|CABLE TABLE|| in the report

RadiMation version 2016.1.2

• #5587: Old LLF is not removed and not replaced with newly added LLF
• #5969: R&S ESU EMI receiver is only set to integer frequency values
• #6393: Graph is covering a rang and analyser is performing a test outside the specified bands
• #6464: Automatic search of highest peaks is changing graph shape
• #6466: Driver R&S FSL
• #6470: Driver R&S NRP2 powermeter
• #6518: FSU 3 error -200 Option ot available INP:PRES:STAT ON during test initialization
• #6723: Broadband disturbances are showed as peaks
• #6804: AD converter values of older tests are not correctly showed in latest versions
• #6865: Implement retry of Software Update used for RadiField amplifier firmware updating
• #6903: Add an additional 'Maximum cable length' field for a cable in the EUT
• #6904: Add a note field to a cable
• #6912: RadiLog icon disappears when pinned to the taskbar
• #6972: RadiLog is not able to write to temporary directory
• #6981: Setup program doesn't check if .NET framework 4.6.1 is installed
• #6985: Advantest TR4172 as powermeter is not correctly measuring
• #6986: RadiLog icon disappears when pinned to the taskbar
• #6988: R&S FSU: Not possible to select 50 MHz RBW
• #6991: How to determine the compression level using a constant output power test
• #6992: Software update will crash RadiMation when a connection error is found
• #6993: RGN Setting the output level raised an error
• #6994: R&S FSU undefined header -113 INP:TYPE INPUT1 error
• #6999: Time interval of table data from a multiband immunity test in the report skips rows if a large delay was present during the test
• #7005: Limitlines are not shown when old test results are opened
• #7008: Reflected power too high
• #7011: RGN software update panel should be hidden
• #7012: Implement checking of system errors for RGN
• #7014: Report Generator can be used without a license

RadiMation version 2016.1.1

• #5988: Driver Teseq ITS6006 for IEC61000-4-3 & CISPR11 as Signal Generator
• #6556: Update the CD Start menu for 2016.1
• #6558: Update version and copyright years to 2016
• #6965: Add ability to return the RAW AD Converter value
• #6983: Empty tabs and no labels are shown after fresh installation
• #6998: Data table from Multiband Immunity in the report generator is always using time interval mode
• #7003: Device check of the R&S SMB100A is unsuccessful