Release Notes/Solved items Version 2016.2

RadiMation version 2016.2.11

• #7981: Device stays in remote after reaching the end frequency
• #8007: Turning of the MAHA turntable is not working
• #8051: ESIB 40 FFT mode cannot be active in zero span
• #8057: Harmonic Test Calibration with Aronia
• #8070: Driver: RadiSense 10 Field sensor
• #8075: Driver: Emtest CWS500N1 Signal Generator
• #8117: R&S ESPI 3 Impossible to get description string for this Error when opening ShowConfigurationDialog
• #8126: Driver: NoiseKen Amplifier
• #8128: Driver: EUT Monitor R&S UPV
• #8208: Frequency is not set in the PMM 8053A
• #8216: How to connect a Rohde & Schwarz NRP6A power sensor?
• #8217: Ability to set the R&S ESW26 Analyser number of points to a maximum of 32000
• #8231: Driver: Keysight Technologies 33612A Signal Generator
• #8242: Support 4 kHz option of RadiPower
• #8243: Unknown error in control of Climat Chamber
• #8247: Tektronix Oscilloscope returns No data or incorrect data was returned by the device
• #8250: Passive drivers CEATSA (ARSAT)
• #8251: Driver: Antenna tower controller ETS-Lindgren 2090 Positioning Controller
• #8252: Driver: Amplifier IFI S251-500
• #8253: Driver: Amplifier IFI T2575-500
• #8256: Driver: Powermeter NRP-Z55/NRP-Z5
• #8257: Crash with Fluke 8845A Multimeter
• #8259: Driver: special RadiSense justation device driver
• #8278: What is the latest RadiMation version running on Windows XP?
• #8286: Extend R&S ESR3 driver to allow selection of CISPR-Average or (old-)Average as Average detector
• #8289: Extend R&S ESPI7 driver to allow selection of CISPR-Average or (old-)Average as Average detector
• #8291: Driver: CWS 500N3 as Amplifier
• #8292: Driver: CWS 500N3 as Coupler
• #8293: Driver: CWS 500N3 as Powermeter (in V mode)
• #8294: Driver: CWS 500N3 as Current sensor (in I mode) as Multimeter
• #8295: Magnetic field testing ISO 11452-8 using the EMTest CWS500N3
• #8298: Driver: Virtual ESD device driver
• #8314: Communication is getting out of sync using a Configurable Antenna Tower driver
• #8323: Driver: is the Frankonia EFS 10 (EFS-100) Field sensor supported?
• #8326: Unexpected responses from RGN device seems to out sync and disturb communication causes "'Setting the output raised an error"
• #8328: LumiLoop LS Probe raises "Setting the frequency raised an error"
• #8333: How to tweak monitoring Field sensor measurements configuration for more reliable measurements?
• #8336: Low field strengths values are increasing signal generator carrier level to the maximum during 61000-4-3 calibration
• #8339: Are previous RadiMation version still usable after updating to a newer RadiMation version?
• #8343: Signal generator drivers (e.g. RGN0230A) raising Unknown Device Driver error
• #8345: Session for reconfiguration of the complete RadiMation installation
• #8348: PMM 8053A: Setting or enabling the frequency correction feature raised an error
• #8350: RF Relay Matrix Unit RFM-S3A3CILR and RFM-S2A2CILR and RFM-E521_231_241
• #8351: R&S ESI 26 Specific System Error: -200 Execution error; Option not available; SCAN1:INP:ATT 50 DB
• #8353: Adjust the RadiSense justation driver having the calculation accepting Signal Generator power levels
• #8367: RadiLog description containing a ";" removes 1 space
• #8369: Amplifier IFI S251-500 Not all bytes are written to the GPIB-Board within the timeout period (GPIB: EABO)
• #8370: Amplifier IFI T2575-500 Not all bytes are written to the GPIB-Board within the timeout period (GPIB: EABO)
• #8373: How to configure the used (EMI) filter of the equipment?

RadiMation version 2016.2.10

• #1391: 0% Step possible in Radiated and Conducted Immunity
• #5347: ESPC is returning a timeout error after CAL?
• #5907: Error detected during the start of the sweep with PMM 9010F
• #6331: Driver: Configurable Multimeter
• #6371: Driver: Signal Generator PMM3010
• #6415: Driver: IFI T188-500 Amplifier
• #6679: Driver: Tektronix TDS310 Oscilloscope
• #6680: Driver: Tektronix TDS3052B Oscilloscope
• #6681: Driver: Tektronix DPO3010 Oscilloscope
• #6691: Driver: Bonn Elektronik BLWA series amplifiers
• #6859: Driver: AR 1000W1000E
• #7299: Selection of Input 2 for the TDEMI X
• #7424: Keysight N9083A runs incredibly slow after 3.6 GHz in scanned receiver mode
• #7545: Driver: battery powered RadiField Polarizer RPL2010A
• #7567: Driver: ADC NI 9215
• #7646: Driver: Frankonia FC04
• #7694: Pulse modulation IFR 2023B Signal generator is not turned off by sending the correct command
• #7992: Measurement with FSV3 power meter is slow and instable
• #7996: Raise a warning that still an outdated or old version of National Instrument GPIB software is used
• #8018: Configurable Absorbing Clamp custom frequency range is not retained
• #8038: Hameg HMS3010 Spectrum Analyser Error: -222, "Data out of range"
• #8042: Hameg HMS3010 Spectrum Analyser is returning previous measured peak data
• #8048: PMM 9010 Comport already open error when using Userport Controlled LISN and receiver simultaneously
• #8049: Hameg HMS3010 Spectrum Analyser has restricted RBW filters for (receiver mode) QP detector
• #8050: RadiMation crashes when using Agilent N9038A
• #8051: ESIB 40 FFT mode cannot be active in zero span
• #8052: Maturo MCU Turntable controller returns E-D error
• #8055: How to perform magnetic immunity calibration?
• #8060: How to make the dwell time depending on an external EUT monitoring device?
• #8063: Driver: Bonn BSA 1010-125 and generic series driver
• #8063: Driver: Bonn BSA 1010-125 and generic series driver
• #8073: Driver: ETS-Lindgren 3142B Antenna
• #8074: Driver: ETS-Lindgren 11966P Antenna
• #8076: Driver: Injection device Luthi RF current Injection clamp
• #8078: Driver: CDN M2-M3N
• #8080: Driver: ESD Generator
• #8082: Driver: Bonn BLMA 1030-80 series
• #8084: R&S FSH 8 Field probe attenuator
• #8088: Gauss Instruments TDEMI: Specific System Error: -100,SYSTRF DEF
• #8089: Gauss Instrument TDEMI3G: Specific System Error: -220,"Parameter Error;SYST:RF DEF"
• #8090: RadiGen RGN start frequency can't go lower then 9 kHz
• #8098: RGN6000B "Data out of range" error when setting carrier level above 4.0 dBm
• #8100: Driver: TESEQ BHA 9118 Horn Antenna
• #8102: Driver: Anapico APSIN12G Signal Generator
• #8103: Driver: AR DC7441A Coupler
• #8110: Ability to control the ALC mode of the Agilent N5183A
• #8119: HP3478A as Multimeter is selecting DC voltage instead of AC voltage
• #8122: Driver: Werlatone C2630-10
• #8132: Ability to control the Pulse limiter and the Pre-selector of the PMM 9010F
• #8135: Configurable device driver write an empty 'Get ID' query and is also trying to read a response
• #8142: Driver: Bonn BSA series interlock
• #8143: RadiSense V Field sensor new firmware implementation
• #8150: Time-out and unlogic measurement values while using multiple PMM EP-601 simultaneously
• #8161: CI calibration is not reaching the desired test level
• #8166: LumiLoop LS Probe TCPIP controlled CI Serial Number raised an error
• #8187: Communication problems with TDEMI 1G, selecting the input
• #8189: Logarithmic step frequency of 0.5% is not used in a CI Calibration
• #8375: 0dBm input limit of amplifier is reached, limited to 4Vrms
• #8376: Signal generator cannot get low enough
• #8385: RIGOL DSA815 is not working because USB TMC driver from NI VISA 17.0 is not working correctly

RadiMation version 2016.2.9

• #2558: Driver RadiLink as cable
• #3534: Driver: Agilent 34980A as an oscilloscope
• #4063: Driver Milmega AS0860-15/25 RF usb controlled
• #4076: RadiSense III not working
• #4213: Driver EMControl Antenna tower
• #4259: Driver: Configurable Field Probe doesn't work with HI6005
• #4809: Driver: Hameg HMS3010 Spectrum Analyser
• #6142: Driver: emtest UCS500N: Telecom line surge: 2 line / 4 line
• #6356: Driver: FCC Bulk Current Injection probes
• #6407: Driver: IFI SMX-500 Amplifier
• #6803: R&S ESU 40: Error -222: Data out of range FREQ:CW 4500 000 000 HZ
• #6870: Driver HP 3458A Multimeter as AD Converter
• #6970: Problems and overrange detected during CI Calibration
• #7181: Driver: euro EMC RSC
• #7244: Detect the 'Not referenced' state of the Maturo MCU controller
• #7299: Selection of Input 2 for the TDEMI X
• #7324: Prana MT400 Amplifier still in operate
• #7325: Prana MT400 Amplifier not always to RF-ON
• #7477: Driver: Bonn elektronik BLMA1060-50 Amplifier
• #7604: Driver: BONN BLWA 0810-200/100 LAN
• #7664: Unknown error: -1073807343
• #7705: R&S SMT 06 Pulse modulation sometimes show a wrong pulse width setting
• #7742: Amplifier Linearity test is not working when a variable testlevel is used during the calibration
• #7771: R&S ESI as powermeter is measuring too fast
• #7784: Preamplifier of Rigol DSA815 is not working in the GTEM test
• #7814: Teseq PCJ 9201B: Unknown Device Driver
• #7816: Driver Rohde & Schwarz BBA150 powermeter(s)
• #7837: Driver: DARE!! Instruments BCI1004A
• #7839: Settings to select 3 axes besides isotropic for Narda EMC 300 field probe
• #7846: Ok button is not working caused by powermeter settings panel
• #7850: RadiCentre 1 with RSS1006A controlled by RS232 is not working correctly
• #7861: RadiSense is not working
• #7862: Selecting an invalid baudrate doesn't raise a specific error message
• #7864: Previous environmentaldata is not always remembered
• #7865: Agilent SG 33120A is not turning on the output
• #7871: Driver Rigol DSG830
• #7872: Preamplifier on DSA832 cannot be activated during SB GTEM test
• #7875: Driver CWS 500N3
• #7891: Driver: Antenna ETS-LINDGREN GTEM 5317
• #7895: TDEMI Device Not connected
• #7900: Maturo MCU has slow communication
• #7901: ControllerDelay for a GPIB controlled Maturo MCU can be 0
• #7910: Extend PMM9010 driver to allow selection of CISPR-Average or (old-)Average as Average detector
• #7914: Clicking on a peak in the emission frequency graph very often moves the frequency of the peak
• #7920: Selection of DC Coupling on R&S ESW8 Input 2 is not possible
• #7923: Driver Agilent 3499A Switch Matrix
• #7931: Catch BONN BSA 0110-100 EXECUTION_RESULT errors
• #7933: Optimize communication with RadiGen
• #7938: Signal generator VI modulation frequency is incorrectly set
• #7941: Maturo NCD controller Device Not Connected
• #7942: How to configure R&S BBA150 amplifier communication settings
• #7943: 1000W1000 input invalid correction file
• #7944: Ability to set a signal generator frequency offset for AnalyzerAsPowerMeterDecorator
• #7952: Driver: R&S FSH 8 as readout unit for field probe
• #7960: Receiver measurement from 500 kHz - 1800 kHz on the ESI results in a timeout
• #7968: Radimation is working in "EFT Multiband" only. The test in "EFT" is not performed
• #7972: RGN Data out of range error during initialization
• #7973: Control of RadiSense III raises the error: E3 Invalid Command
• #7979: Missing test equipment in the Report Generator
• #7982: Ability to define a power offset for the RPR RadiPower
• #7984: RadiCentre controlled devices are not setting the RadiCentre back to local
• #7997: R&S URV35 Level Meter as AD Converter
• #8002: Driver: ETS-Lindgren HI-6006 Field Sensor
• #8010: Driver DARE!! Instruments BCI1004A Coupler
• #8012: Environmental data window unable to press OK
• #8013: Agilent Technologies E4432B: Not all bytes are written to the GPIB-Board within the timeout period (GPIB: EABO)
• #8019: Compression EUT Calibration table export same for every compressionPoint
• #8026: Driver: Hameg HMS3010 as Powermeter
• #8062: Outside Points
• #8153: Provide C header file for Device Driver API, to make importing in ATEasy software possible
• #8164: Provide C header file for Device Driver API, to make importing in ETSI Power Meter 300328

RadiMation version 2016.2.8

• #4497: Calculation of the number of frequency steps generates an unhandled exception
• #6690: Driver: Bonn Elektronik BTA series amplifiers
• #7039: Limitlines color issue
• #7128: Index was outside the bounds of the array error 536879965
• #7179: Deadlock Unknown SetValueID
• #7182: Reopening Surge TSF file gives error
• #7257: Change Basic small controlling window for FieldSensor
• #7439: Graph from Burst Measurement disappears
• #7444: Opening VI PowerMeter takes long time file loading
• #7473: Error description unavailable
• #7519: Error after saving EUT
• #7643: RadiLog crash when ":" is in subject text.
• #7707: Graph Visibility states not remembered
• #7711: Skip report generator tests in template functionality is not working.
• #7840: Deadlock when Report Generating a CE MB test
• #7841: Unable to overwrite normal.dotm during Report generation
• #7857: Report generator code is changing the visibility states settings for the test results
• #7874: Repeating a sweep in a stored file (small bandwidth)
• #7876: DC Coupling Test Initialization Error
• #7880: Amplifier Linearity test
• #7899: How to retrieve the VBW and RBW of the second band in the Report generator
• #7928: Driver TTi CPX 400 DP as AD Converter
• #7959: Re-measuring peaks gives NI hibernation
• #7976: Powersensor (ID1576/ID1497): Device Not Connected.
• #8006: StartEnd deleteblock genereates a newline
• #8055: How to perform magnetic immunity calibration?
• #8182: GraphControlls stays disabled
• #8352: New lng files with new DareLang.dll with old RadiMation causes glitches: Â

RadiMation version 2016.2.7

• #3965: Is not possible to choose between EXT-AC and EXT-DC using the siggen HP8648A
• #5758: Driver Monitor OSD dAV-C(r)-SD/HD
• #6111: R&S AFG device check seems to be always successful
• #6557: Update the CD Start menu for 2016.2
• #7287: Possibility to specify the Attenuation in the generic Powermeter-Analyser device driver
• #7740: Amplifier Linearity in Net power calibration method
• #7776: Driver All other ETS-Lindgren 8100-series amplifiers
• #7805: Deadlock when reviewing a RE Burst test results
• #7809: emtest CWS500N2.2 powermeters are not correct
• #7810: HP85xx-series has timeout after DONE query
• #7813: Clicking Full Span gives error and crash radimation
• #7815: Rohde & Schwarz ESW8 returns Device not connected
• #7817: Driver: PMM SB-10
• #7821: Driver: UCS500Mx
• #7838: Driver R&S ESR as powermeter
• #7851: Unknown GetValueID error when using a 1 ohm resistor
• #7855: Opening older test results triggers errors of wrong correction files
• #7856: Null reference exception during selection of EUT file, caused by ProposedSaveEUTFilename
• #7858: Opening older test results shows an error of an incorrect number of columns in the correction file

RadiMation version 2016.2.6

• #3168: Is amplifier protection working in a multiband immunity test
• #3517: Radiated Immunity: Level is going too high
• #4397: Forward power protection file for an Amplifier is ignored if power is already limited
• #4586: Amplifier limit completely ignored
• #5099: Too much data point with ESU8 and out of memory errors
• #5767: ESR7 is an unknown device driver
• #5952: Error ESRP 3 Receiver DC: More points received from the receiver/analyser then calculated
• #6853: Decrease testlevel is not available anymore as a shortcut key action
• #6855: Limitation of a Multiband Immunity test on the current is levelling just above the limit
• #7372: Driver: LSProbe from LumiLoop GmbH
• #7459: RadiPower driver doesn't support POWER? in mode 3
• #7800: Frequency span is not always correctly selected on the Advantest TR4172
• #7801: Only 51 peaks are detected

RadiMation version 2016.2.5

• #3489: Add support for IEC 61000-4-11: Voltage dips and Interrupts for AC mains
• #6109: Incorrect AD measurement after AD channel settings are unexpectedly changed
• #6127: Older TSF file with minimum performance limit is not working anymore and is crashing the software
• #6128: Small dips in negative singleband Emission results
• #6172: Add support for IEC 61000-4-29: Voltage dips and Interrupts on DC input power
• #7621: Exporting Report Generator using different extentions for template as the output, causing error cannot open file
• #7635: Error access to the path (..) is denied after Network Analyser Calibraton
• #7650: Voltage test level Voltage measurement (Powermeter) is not measured
• #7712: No easy manner to activate or deactivate all available Monitoring input channels
• #7770: Removing Test level from RI MB is closing the test and also gives error
• #7774: Correction of resistor is not used in magnetic field measurement
• #7788: Environmental data window can be shown behind mainwindow

RadiMation version 2016.2.4

• #4132: Minimum performance with pulse modulation not working correctly
• #6301: Preamplifier setting is not visible anymore in the CE MB TSF window
• #7428: Load XML error at RadiMation Startup
• #7640: Crash during startup due to newer CUSTOMIZ.XML
• #7658: Ability to physically us one powermeter multiple times in RadiMation to measure forward and reflected power
• #7714: Unlogic that the (activated) Monitoring input channels are used during Radiated Emission
• #7758: Error is raised that columns contains 3 columns, even if only 2 columns are present
• #7765: Error the maximum recursive read count has been reached during startup

RadiMation version 2016.2.3

• #2079: Usage of Amplifier protection is not clear if correction file has wrong columns
• #2631: Changing the minimum attenuation value argument in the device driver is changing the set attenuation
• #4209: No frequency verification on correction file
• #4380: CI multiband: crash during changing the band
• #5071: N9010A is not recognized anymore Unknown system error
• #5505: Rounding issues of Correction values (COR) when copied to clipboard
• #5515: Different measurement results with Singleband and Multiband test for Fixed Power method
• #5647: Correction file doesn't allow logarithmic interpolation of the value
• #6101: Disable all menu and editable items of which an engineer has no rights
• #6736: Correction is remembered in Virtual Instrument Powermeter when the correction file is detached again
• #6984: Infinite regulation when amplifier is in noize region
• #6987: RadiLog in 64 bits
• #6996: Peak numbering for emmission measurements are not shown and can't be sorted
• #7015: Radiated Immunity variable power closed loop with current sensor is endless regulating at first point
• #7159: RadiLog crashes with out of memory during a big test
• #7161: 7th point in RI calibration
• #7288: RadiLog slow with big description
• #7393: 'Output boxes' is shown as 'Unknown device driver types' in the 'Devices' menu
• #7445: Reflected powermeter measurements are not corrected
• #7533: Multiband Ok button of 'Continue automatic mode settings' is disabled
• #7555: Duplicate other test description menu in the graphs menu
• #7579: Copying the information of the EUT Monitoring grid to clipboard causes crash
• #7581: Test description of the test is not visible in the test data
• #7594: Radilog Deleted log when closing test
• #7595: RadiLog cleared within sequence
• #7569: Usefull RadiLog default description when sending an error report
• #7597: RadiLog Error Report disappearing window after sending log
• #7617: Cancelling the closing of the VI Fieldsensor results in a not working window
• #7618: Export of time-graph doesn't export all the data
• #7621: Exporting Report Generator using different extentions for template as the output, causing error cannot open file
• #7627: Endless regulation at frequency point during RI Fixed power test
• #7649: ReportGenerator to much capital letters
• #7660: Adjusted Fieldstrength units are not used in the scaling of the VI graphs
• #7663: CONFDVDR deadlock when Access to the path (..) is denied error is raised
• #7688: Correction data is not correctly determined from unsorted correction file
• #7691: Exporting graph to LLF doesnt show the in graph
• #7692: Copying the EUT Monitoring table to the clipboard causes a crash
• #7719: Exporting AD channels
• #7725: Multiple cosmetic changes to prevent controls from being hidden when window is resized
• #7726: Unicode: EUT files with chinese characters in the filename are not loaded correctly
• #7729: RadiLog doesn't show full binary data strings
• #7734: Report Generator code Step Frequency for ConEmi absorbtion clamp
• #7735: Unicode: INI files in unicode
• #7748: Unicode: Test-Sites

RadiMation version 2016.2.2

• #1688: Cannot save multiband test
• #3398: Test on hold when opening RE Multiband file
• #4074: Optimize angle is not measuring every area
• #4155: Device specific parameters are not retrieved when a device driver is created
• #4714: Cable loss correction applied to the Cable antenna Preamp is incorrect
• #4771: Adding cable with default port type value is not correct
• #4800: Comparing test data and zooming graphs in Multiband is not working
• #4823: CORrection factor current probe is not taken into account
• #4855: Possibility to directly open device driver TYPE window and TAB by just one click
• #4892: RM crash during RPR2006P Free mode when test equipment is opened
• #5222: Add a Virtual Instrument for the Amplifier
• #5223: Add a Virtual Instrument for the Signal generator
• #5270: Peak conservation setting is ignored for Singleband Radiated Immunity
• #5368: Graph data is not updated
• #5550: Add an 'Configure...' menu entry in all the sub-menus of the Devices menu
• #5565: Opening the virtual powermeter window shows a corrupt file error
• #6130: Device driver: emtest VCS 500
• #6228: Cable correction is not correctly taken into account during the Current Probe test
• #6421: Multiband graph is not exporting vertical and/or horizontal polarization graph
• #6667: Virtual Instruments should be able to collapse to a 'mini' mode that only shows the measurement value
• #6703: Driver: em test PFS 500
• #6704: Driver: em test MV2616
• #6705: Driver: emtest UCS500N5: voltage dips and interrupts support
• #6745: Include a 'Clear' button on the VI Fieldstrength sensor to clear the (time-)graphs
• #6746: Lower and upper value of the analog meter on the VI should be autoranging
• #6747: Show the 'table' tab for the time-graph in a virtual instrument
• #6749: Time graph in Virtual Instrument is using the wrong date
• #6750: Time graph of a Virtual Instrument should have a minimum time range of 30 seconds
• #7040: Marconi signal generator doesn't respond on *STB?
• #7065: A MB emission test shows a 'Fail', even if all emissions are below the limit
• #7102: Backwards sweeping is not correctly handled
• #7151: VDI: ProgressBar starts at 99%
• #7202: Longer time till sleep mode Narda EP600/EP601
• #7205: Default settings of Multiband EFT is not logical
• #7206: Default settings of Multiband Burst is not logical
• #7210: emtest PFS 500N Not all bytes are written
• #7213: Sequence are shuffled
• #7230: VIBase not always (dis)connecting
• #7231: Add suggested values
• #7234: Unit window showing example of setted settings.
• #7235: Clear Graph button in the VIBase is not correctly implemented.
• #7239: Unable to clear graph in VI windows while trigger is set to auto.
• #7250: Unit settings example is not correct with a precision of 0
• #7251: Unit settings applied to AnalogMeter control before init
• #7276: Unit settings are applied on fieldsensor not on the ctlAnalogDigitalMeter control itself.
• #7307: Error messages in the VI Powermeter are not shown
• #7327: Not controllable EFT and Surge device drivers should raise an error, early at the automated test
• #7328: Multiband EFT Test is in a continuous loop, when an error is raised
• #7335: Determined Forward power step during amplifier linearity is 100000 dB
• #7360: Calculated graph is recalculated 6x when an additional non-relevant graph is shown
• #7363: VIBase not always (dis)connecting
• #7364: 'Clear' button is hidden when the VI window is resized when the device is disconnected
• #7366: Resizing of 'Logging' tab of VI Powermeter is not done when another tab is active
• #7367: Tabs on the VI Powermeter should be hidden when the size of the window becomes too small
• #7368: Hide the analog meter if it becomes too small
• #7369: Improvements for the VI Turntable window
• #7370: Allow smaller size of VI Antenna tower
• #7371: A VI window should remember it's location and size
• #7373: RadiFree warnings
• #7374: Location and size of the window is not remembered if the RadiMation main window is closed with windows open
• #7375: Settings of the VI Signal generator are not set in the signal generator after a connect
• #7376: Clear button of a VI should also be enabled when the device is disconnected
• #7377: Clear button should be pressed automatically when the VI window is closed
• #7378: Only show the test initialization window if it contains more than 1 item
• #7380: Auto-Show and Auto-Connect for VI devices
• #7388: Resizing of the contents of the VI Powermeter window is incorrect
• #7389: Virtual Instrument window of the Virtual signal generator is always showing disabled controls
• #7391: Improve the showing of the 'Devices' menu
• #7396: RadiMation crashes during start with open automatically connecting VI windows
• #7410: Saving a test equiment with changing just 1 char to uppercase seems to overwrite the existing test equipment
• #7413: Unit Volts per meter shows only V
• #7417: Validation documentation of RadiMation
• #7429: Correction of Monitoring Input powermeter is also applied to the used (forward) powermeter during the test
• #7442: Invisible Clear Button
• #7443: Visible progress bar
• #7446: Reflected powermeter measurements data is incorrectly shown
• #7452: Improve the showing of the "Test-Site Menu"' menu
• #7453: Device menu also contains an Add Device button
• #7458: Address Information will pause a running test
• #7464: Name the log file the same as the subject description instead of always Last error report
• #7470: VI Signal Generator Carrier ON and OFF control has incorrect triggering
• #7507: Graphs are not drawn when 'Ramp' method is used in MB Immunity
• #7512: Virtual burst powermeter doesn't work anymore in RadiMation Free 'Burst' mode
• #7529: New testsites are shuffled in the Test-Sites list
• #7598: Error report, customer information is not remembered

RadiMation version 2016.2.1

• #6218: TSF description inside a SEQuence is changed to No Description
• #6634: Project: Voltage dips and interrupts
• #7004: Pasting large data (19000 rows) into a COR file is crashing RadiMation
• #7018: System error is not included in the Report Error
• #7026: Closing the adding of a short cut key is still adding the entry
• #7027: Save as test equipment buttons are incorrectly alligned
• #7029: RS232 communication method available for the Keysight N9038A while the device does not support it
• #7060: Changing a value in the Advanced Options grid, resizes the columns to very small
• #7121: The attenuation in MB Emission shows: Auto (100 dB)
• #7122: Layout of CE Multiband TSF is strange
• #7150: VDI: ReducedVoltageTime not marked in seconds
• #7152: VDI: Adding EMtest VDI driver.
• #7153: VDI: Remove workaround in device driver Keytek
• #7154: VDI: Repeat count
• #7155: VDI: Repetition time is not passed to the driver yet.
• #7157: VDI: Only show available line couplings.
• #7158: VDI: Debug EMTest UCS500N VDI driver on the device itself until it works.
• #7160: VDI: LineCoupling ignored error when starting test
• #7162: A strange symbol as digit seperator is not used in the interpretation of a string
• #7164: VDI: Phase Angles
• #7165: Repetition count
• #7166: SurgeMB phase angle cannot be selected
• #7172: VDI: ReducedVoltageTime not marked in seconds
• #7186: VDI: Reopening VDI with multiple bands shows unable to start error.
• #7527: Include ADVANCED.INI and TUNING.INI in an error report
• #7530: Selecting 'AD converter selected in testsite' as monitoring input device is default selecting 'nothing' instead of channel 1 resulting that nothing will be measured
• #7540: Channel numbers are all default set to 0