Release Notes/Solved items Version 2016.2.10

RadiMation version 2016.2.10

• #1391: 0% Step possible in Radiated and Conducted Immunity
• #5347: ESPC is returning a timeout error after CAL?
• #5907: Error detected during the start of the sweep with PMM 9010F
• #6331: Driver: Configurable Multimeter
• #6371: Driver: Signal Generator PMM3010
• #6415: Driver: IFI T188-500 Amplifier
• #6679: Driver: Tektronix TDS310 Oscilloscope
• #6680: Driver: Tektronix TDS3052B Oscilloscope
• #6681: Driver: Tektronix DPO3010 Oscilloscope
• #6691: Driver: Bonn Elektronik BLWA series amplifiers
• #6859: Driver: AR 1000W1000E
• #7299: Selection of Input 2 for the TDEMI X
• #7424: Keysight N9083A runs incredibly slow after 3.6 GHz in scanned receiver mode
• #7545: Driver: battery powered RadiField Polarizer RPL2010A
• #7567: Driver: ADC NI 9215
• #7646: Driver: Frankonia FC04
• #7694: Pulse modulation IFR 2023B Signal generator is not turned off by sending the correct command
• #7992: Measurement with FSV3 power meter is slow and instable
• #7996: Raise a warning that still an outdated or old version of National Instrument GPIB software is used
• #8018: Configurable Absorbing Clamp custom frequency range is not retained
• #8038: Hameg HMS3010 Spectrum Analyser Error: -222, "Data out of range"
• #8042: Hameg HMS3010 Spectrum Analyser is returning previous measured peak data
• #8048: PMM 9010 Comport already open error when using Userport Controlled LISN and receiver simultaneously
• #8049: Hameg HMS3010 Spectrum Analyser has restricted RBW filters for (receiver mode) QP detector
• #8050: RadiMation crashes when using Agilent N9038A
• #8051: ESIB 40 FFT mode cannot be active in zero span
• #8052: Maturo MCU Turntable controller returns E-D error
• #8055: How to perform magnetic immunity calibration?
• #8060: How to make the dwell time depending on an external EUT monitoring device?
• #8063: Driver: Bonn BSA 1010-125 and generic series driver
• #8063: Driver: Bonn BSA 1010-125 and generic series driver
• #8073: Driver: ETS-Lindgren 3142B Antenna
• #8074: Driver: ETS-Lindgren 11966P Antenna
• #8076: Driver: Injection device Luthi RF current Injection clamp
• #8078: Driver: CDN M2-M3N
• #8080: Driver: ESD Generator
• #8082: Driver: Bonn BLMA 1030-80 series
• #8084: R&S FSH 8 Field probe attenuator
• #8088: Gauss Instruments TDEMI: Specific System Error: -100,SYSTRF DEF
• #8089: Gauss Instrument TDEMI3G: Specific System Error: -220,"Parameter Error;SYST:RF DEF"
• #8090: RadiGen RGN start frequency can't go lower then 9 kHz
• #8098: RGN6000B "Data out of range" error when setting carrier level above 4.0 dBm
• #8100: Driver: TESEQ BHA 9118 Horn Antenna
• #8102: Driver: Anapico APSIN12G Signal Generator
• #8103: Driver: AR DC7441A Coupler
• #8110: Ability to control the ALC mode of the Agilent N5183A
• #8119: HP3478A as Multimeter is selecting DC voltage instead of AC voltage
• #8122: Driver: Werlatone C2630-10
• #8132: Ability to control the Pulse limiter and the Pre-selector of the PMM 9010F
• #8135: Configurable device driver write an empty 'Get ID' query and is also trying to read a response
• #8142: Driver: Bonn BSA series interlock
• #8143: RadiSense V Field sensor new firmware implementation
• #8150: Time-out and unlogic measurement values while using multiple PMM EP-601 simultaneously
• #8161: CI calibration is not reaching the desired test level
• #8166: LumiLoop LS Probe TCPIP controlled CI Serial Number raised an error
• #8187: Communication problems with TDEMI 1G, selecting the input
• #8189: Logarithmic step frequency of 0.5% is not used in a CI Calibration
• #8375: 0dBm input limit of amplifier is reached, limited to 4Vrms
• #8376: Signal generator cannot get low enough
• #8385: RIGOL DSA815 is not working because USB TMC driver from NI VISA 17.0 is not working correctly