Release Notes/Solved items Version 2016.2.11

RadiMation version 2016.2.11

• #7981: Device stays in remote after reaching the end frequency
• #8007: Turning of the MAHA turntable is not working
• #8051: ESIB 40 FFT mode cannot be active in zero span
• #8057: Harmonic Test Calibration with Aronia
• #8070: Driver: RadiSense 10 Field sensor
• #8075: Driver: Emtest CWS500N1 Signal Generator
• #8117: R&S ESPI 3 Impossible to get description string for this Error when opening ShowConfigurationDialog
• #8126: Driver: NoiseKen Amplifier
• #8128: Driver: EUT Monitor R&S UPV
• #8208: Frequency is not set in the PMM 8053A
• #8216: How to connect a Rohde & Schwarz NRP6A power sensor?
• #8217: Ability to set the R&S ESW26 Analyser number of points to a maximum of 32000
• #8231: Driver: Keysight Technologies 33612A Signal Generator
• #8242: Support 4 kHz option of RadiPower
• #8243: Unknown error in control of Climat Chamber
• #8247: Tektronix Oscilloscope returns No data or incorrect data was returned by the device
• #8250: Passive drivers CEATSA (ARSAT)
• #8251: Driver: Antenna tower controller ETS-Lindgren 2090 Positioning Controller
• #8252: Driver: Amplifier IFI S251-500
• #8253: Driver: Amplifier IFI T2575-500
• #8256: Driver: Powermeter NRP-Z55/NRP-Z5
• #8257: Crash with Fluke 8845A Multimeter
• #8259: Driver: special RadiSense justation device driver
• #8278: What is the latest RadiMation version running on Windows XP?
• #8286: Extend R&S ESR3 driver to allow selection of CISPR-Average or (old-)Average as Average detector
• #8289: Extend R&S ESPI7 driver to allow selection of CISPR-Average or (old-)Average as Average detector
• #8291: Driver: CWS 500N3 as Amplifier
• #8292: Driver: CWS 500N3 as Coupler
• #8293: Driver: CWS 500N3 as Powermeter (in V mode)
• #8294: Driver: CWS 500N3 as Current sensor (in I mode) as Multimeter
• #8295: Magnetic field testing ISO 11452-8 using the EMTest CWS500N3
• #8298: Driver: Virtual ESD device driver
• #8314: Communication is getting out of sync using a Configurable Antenna Tower driver
• #8323: Driver: is the Frankonia EFS 10 (EFS-100) Field sensor supported?
• #8326: Unexpected responses from RGN device seems to out sync and disturb communication causes "'Setting the output raised an error"
• #8328: LumiLoop LS Probe raises "Setting the frequency raised an error"
• #8333: How to tweak monitoring Field sensor measurements configuration for more reliable measurements?
• #8336: Low field strengths values are increasing signal generator carrier level to the maximum during 61000-4-3 calibration
• #8339: Are previous RadiMation version still usable after updating to a newer RadiMation version?
• #8343: Signal generator drivers (e.g. RGN0230A) raising Unknown Device Driver error
• #8345: Session for reconfiguration of the complete RadiMation installation
• #8348: PMM 8053A: Setting or enabling the frequency correction feature raised an error
• #8350: RF Relay Matrix Unit RFM-S3A3CILR and RFM-S2A2CILR and RFM-E521_231_241
• #8351: R&S ESI 26 Specific System Error: -200 Execution error; Option not available; SCAN1:INP:ATT 50 DB
• #8353: Adjust the RadiSense justation driver having the calculation accepting Signal Generator power levels
• #8367: RadiLog description containing a ";" removes 1 space
• #8369: Amplifier IFI S251-500 Not all bytes are written to the GPIB-Board within the timeout period (GPIB: EABO)
• #8370: Amplifier IFI T2575-500 Not all bytes are written to the GPIB-Board within the timeout period (GPIB: EABO)
• #8373: How to configure the used (EMI) filter of the equipment?