Release Notes/Solved items Version 2016.2.9

RadiMation version 2016.2.9

• #2558: Driver RadiLink as cable
• #3534: Driver: Agilent 34980A as an oscilloscope
• #4063: Driver Milmega AS0860-15/25 RF usb controlled
• #4076: RadiSense III not working
• #4213: Driver EMControl Antenna tower
• #4259: Driver: Configurable Field Probe doesn't work with HI6005
• #4809: Driver: Hameg HMS3010 Spectrum Analyser
• #6142: Driver: emtest UCS500N: Telecom line surge: 2 line / 4 line
• #6356: Driver: FCC Bulk Current Injection probes
• #6407: Driver: IFI SMX-500 Amplifier
• #6803: R&S ESU 40: Error -222: Data out of range FREQ:CW 4500 000 000 HZ
• #6870: Driver HP 3458A Multimeter as AD Converter
• #6970: Problems and overrange detected during CI Calibration
• #7181: Driver: euro EMC RSC
• #7244: Detect the 'Not referenced' state of the Maturo MCU controller
• #7299: Selection of Input 2 for the TDEMI X
• #7324: Prana MT400 Amplifier still in operate
• #7325: Prana MT400 Amplifier not always to RF-ON
• #7477: Driver: Bonn elektronik BLMA1060-50 Amplifier
• #7604: Driver: BONN BLWA 0810-200/100 LAN
• #7664: Unknown error: -1073807343
• #7705: R&S SMT 06 Pulse modulation sometimes show a wrong pulse width setting
• #7742: Amplifier Linearity test is not working when a variable testlevel is used during the calibration
• #7771: R&S ESI as powermeter is measuring too fast
• #7784: Preamplifier of Rigol DSA815 is not working in the GTEM test
• #7814: Teseq PCJ 9201B: Unknown Device Driver
• #7816: Driver Rohde & Schwarz BBA150 powermeter(s)
• #7837: Driver: DARE!! Instruments BCI1004A
• #7839: Settings to select 3 axes besides isotropic for Narda EMC 300 field probe
• #7846: Ok button is not working caused by powermeter settings panel
• #7850: RadiCentre 1 with RSS1006A controlled by RS232 is not working correctly
• #7861: RadiSense is not working
• #7862: Selecting an invalid baudrate doesn't raise a specific error message
• #7864: Previous environmentaldata is not always remembered
• #7865: Agilent SG 33120A is not turning on the output
• #7871: Driver Rigol DSG830
• #7872: Preamplifier on DSA832 cannot be activated during SB GTEM test
• #7875: Driver CWS 500N3
• #7891: Driver: Antenna ETS-LINDGREN GTEM 5317
• #7895: TDEMI Device Not connected
• #7900: Maturo MCU has slow communication
• #7901: ControllerDelay for a GPIB controlled Maturo MCU can be 0
• #7910: Extend PMM9010 driver to allow selection of CISPR-Average or (old-)Average as Average detector
• #7914: Clicking on a peak in the emission frequency graph very often moves the frequency of the peak
• #7920: Selection of DC Coupling on R&S ESW8 Input 2 is not possible
• #7923: Driver Agilent 3499A Switch Matrix
• #7931: Catch BONN BSA 0110-100 EXECUTION_RESULT errors
• #7933: Optimize communication with RadiGen
• #7938: Signal generator VI modulation frequency is incorrectly set
• #7941: Maturo NCD controller Device Not Connected
• #7942: How to configure R&S BBA150 amplifier communication settings
• #7943: 1000W1000 input invalid correction file
• #7944: Ability to set a signal generator frequency offset for AnalyzerAsPowerMeterDecorator
• #7952: Driver: R&S FSH 8 as readout unit for field probe
• #7960: Receiver measurement from 500 kHz - 1800 kHz on the ESI results in a timeout
• #7968: Radimation is working in "EFT Multiband" only. The test in "EFT" is not performed
• #7972: RGN Data out of range error during initialization
• #7973: Control of RadiSense III raises the error: E3 Invalid Command
• #7979: Missing test equipment in the Report Generator
• #7982: Ability to define a power offset for the RPR RadiPower
• #7984: RadiCentre controlled devices are not setting the RadiCentre back to local
• #7997: R&S URV35 Level Meter as AD Converter
• #8002: Driver: ETS-Lindgren HI-6006 Field Sensor
• #8010: Driver DARE!! Instruments BCI1004A Coupler
• #8012: Environmental data window unable to press OK
• #8013: Agilent Technologies E4432B: Not all bytes are written to the GPIB-Board within the timeout period (GPIB: EABO)
• #8019: Compression EUT Calibration table export same for every compressionPoint
• #8026: Driver: Hameg HMS3010 as Powermeter
• #8062: Outside Points
• #8153: Provide C header file for Device Driver API, to make importing in ATEasy software possible
• #8164: Provide C header file for Device Driver API, to make importing in ETSI Power Meter 300328