Release Notes/Solved items Version 2017.1

RadiMation version 2017.1.7

• #6971: Driver: LeCroy WaveSurfer and Wave Runner oscilloscope series
• #8538: Driver: CPI Amplifier J-series
• #8541: Option to enable/disable frequency correction of PMM EP600-series
• #8553: Support Mode 4 of the RadiPower
• #8555: ErrorReport: "Collection was modified; enumeration operation may not execute. "
• #8565: Driver: Steatite atennas
• #8566: Driver: Flann Microwave antennas
• #8569: Use Internal 10 MHz out for IFR 2023 Reference clock
• #8582: Support the Preamplifier of the new TDEMI X
• #8623: line coupling is only showing 1 line coupling in VDI TSF configuration
• #8662: Object reference error while using minimum performance in a MB magnetic field closed loop method test
• #8685: AD Channel colors are the same
• #8689: Note field cannot be larger then 1000 characters.

RadiMation version 2017.1.6

• #4969: CANoe interface object not initialized correctly
• #7496: Sentinel dongle failure
• #7586: Not possible to export attached pictures in the report by using the Report Generator
• #7696: Graph is not showing (correct) trace data during CI calibration and RI Multiband
• #7829: Implement the AnalyserAsPowerMeterDecorator for ESU and ESI series powermeter device drivers
• #8062: Outside Points
• #8068: Marconi 2042: Specific System Error: 2
• #8165: Ability to use AM modulation with the obsolete Agilent Technologies E4432B Signal Generator
• #8287: Extend R&S ESCI driver to allow selection of CISPR-Average or (old-)Average as Average detector
• #8340: Ability of 'Power Measurement' settings for the R&S ESR7 to avoid unexpected bandwidth jump behavior
• #8378: Enabled Calibration before final measurements option causes GPIB: EABO timeout
• #8384: External reference setting of the R&S ZNB is changed during initialization
• #8403: Rotate to position after end of test (de-initialization)
• #8412: Ability of 'Power Measurement' settings for the R&S ESU40
• #8429: Opening of a very large CI Multiband test is very slow
• #8431: Unclear description when the RadiSense is still in standby
• #8444: Driver: BiDirectional Coupler BDC 0660-30/100
• #8446: Driver: Teseq CBA 1G-150 amplifier
• #8450: ESPC Not all bytes are written to the GPIB board "Perform short calibration before final measurement" option
• #8452: IFR 2052 driver is not working correctly
• #8467: RI Multiband AM modulation is only used for first point, after that its none if modulation conservation is activated
• #8477: RadiLog Error Report does not make screenshot from external monitor
• #8479: Maturo MCU raises a Lock error during deinitialization
• #8481: Driver: RSSA3021X Spectrum analyser
• #8483: R&S ESIB40: Function not available;FREQ:STOP:LINK START
• #8488: N9038A: System Error: -410: Query Interrupted
• #8493: CARAD software invalid messages received
• #8503: Marked peaks are not saved
• #8504: Minimum power of CI Fixed power test is -40 dBm
• #8508: Ability to select Internal or External reference clock on some devices
• #8510: Changing unit causes crash
• #8511: Frequency correction of PMM EP603
• #8512: Device Driver: Marconi 2052
• #8518: Not possible to generate a printout of the amplifier linearity test results
• #8523: Compression test table: uses wrong unit in time and frequency column
• #8526: Generated power of CWS500N1 drops at 350 kHz
• #8527: RSSML Merge reference source
• #8556: Negative power reading of NRP-Zxx powermeter
• #8557: Wrong de-initialisation NRP-Zxx
• #8573: Driver Antenna Schaffner Bilog
• #8584: Driver: PMM EP604
• #8602: Driver: Multimeter Agilent 34401A AC and DC measurement
• #8603: Driver: generic configurable coupler for the couplers of ATM Microwave
• #8604: Driver: generic configurable coupler for the couplers of RF Lambda

RadiMation version 2017.1.5

• #7633: Unexpected oscilloscope measurement value of first frequency point
• #7652: Configurable Injection Device custom frequency range is not retained
• #7689: Graph export is showing unexpected end frequency
• #7901: ControllerDelay for a GPIB controlled Maturo MCU can be 0
• #8092: When a printout is generated and printed the 'busy' dialog should be shown, to indicate that the PC is busy
• #8113: Unable to communicate with CWS500N 1.2
• #8233: RadiMate slow measurement speed
• #8247: Tektronix Oscilloscope returns No data or incorrect data was returned by the device
• #8334: No measurement data during "Continuous Measurement" as altitude scan using CO3000 controller
• #8384: External reference setting of the R&S ZNB is changed during initialization
• #8406: Password of a new engineer is unknown, and cannot be changed
• #8408: EUT Monitoring channel Maximum and Minimum Limits are not shown
• #8418: Maturo NCD over lan
• #8419: Settings in 'Fixed step count' frequency step setting in a multiband immunity test is not remembered
• #8420: Fixed step count as step frequency in multiband immunity is not working when 'per octave' is selected
• #8421: Agilent E4422B unable to connect
• #8422: Singleband GTEM emission data is not shown when a dot is used a decimal symbol
• #8423: HP 34401: Timeout while waiting for *OPC command
• #8425: VDI duplicate band Object reference
• #8430: Internal AM modulation on the Agilent E4422B is not supported
• #8433: Exporting of graph data to CSV is not always in Excel compatible format
• #8435: Allow control of CANoe 9.0.65 (SP2)
• #8436: Also notify the CANoe CAPL interface of dwelltime start and dwelltime end
• #8437: Possibility to leave CANoe running when the CANoe switch matrix is used
• #8441: Changing polarization of Frankonia FC02 raises 'Illegal parameter value' error
• #8448: Destination array was not long enough. Check destIndex and length, and the array's lower bounds.
• #8451: CWS500N Checksum error
• #8455: Black lines in RI tests
• #8456: Conducted RF immunity stepsize 0,5 per cent not possible
• #8461: Preselection filter before the test
• #8464: Changing region settings causes data loss.
• #8469: Agilent Technologies E4422B: "Undefined header" when turning off AM modulation
• #8475: When changing step frequency of 1 band, all the bands step sizes change.
• #8476: R&S ESI: Function not available: INP:GAIN:STAT OFF, when FFT filter is used
• #8485: Changing test level settings after its loaded by TSF, is not using last setted device.
• #8486: Export EUT filename shows TSF filename
• #8515: Driver: emtest esd NX30
• #8519: Missing NIPALU.DLL error when starting RadiMation
• #8536: Merge test blank page

RadiMation version 2017.1.4

• #6093: Turntable CO3000 is not moving when setting it to make a full turn from 0 till 360 degrees
• #6798: Apply multiple testlevels at same frequency
• #7780: Exporting EUT executed tests list
• #8207: Configurable Device driver frequencies with different units
• #8244: Climat typo it should be Climate
• #8301: Unhandled exception access to the path ErrorModeFile.radilog is denied
• #8322: RPR2006C overranges during CDN voltage calibration
• #8371: 1% Stepsize in RI Manual mode is not correct when a frequency list is used
• #8382: ODBC customer database is not working anymore
• #8383: Store RADIMAT_SESSION.LOG in a PC local temporary folder
• #8389: Received power is rounded in Antenna Scan EUT Calibration
• #8397: Searching for a customer in the customer database closes the window before the customer can be selected
• #8399: Loading a multiband immunity test is not possible, unable to create VSWRGatherer
• #8415: RadiMation crash at startup after updating to 2017.1.4
• #8416: Agilent N9000A (version A.07.06) Error with GPIB
• #8426: Unable to select correct OPC channels for AD converter.
• #8435: Allow control of CANoe 9.0.65 (SP2)
• #8443: Driver: Amplifier BLMA 1060-50
• #8458: Unable to connect to radigen RADIGEN0230A

RadiMation version 2017.1.3

• #8210: Opening a RE Multiband test is taking one and a half minutes

RadiMation version 2017.1.2

• #8045: RDC files are always stored to the Global configuration path while standalone setting is used
• #8091: Improve calculation of multiband immunity graphs
• #8097: Linear and logaritmische scale setting are not saved
• #8145: Unable to show AD Channels in 2017.1.1
• #8199: Opening Multiband Immunity results takes a lot of time since graph filtering is implemented
• #8238: Language file 0.lng
• #8363: RadiLog option in view menu incorrect behaviour

RadiMation version 2017.1.1

• #506: 1 Hz on off modulation is not possible according to the DO-160E / ED-14E standards
• #2947: Amplifier is turned off when closing another multiband test
• #3032: Opening an Multiband test while performing a Multi band test is messing up the test
• #3241: RI multi band test is overwriting the previous information
• #3598: Configurable Peak Table
• #3970: Radiated emission multiband: detector from pre-measurement used during "continuous measure"
• #4001: Difficulties to differ results from 2 bands with the same frequency range in multiband immunity tests
• #4159: RBW in peak table (RE multiband)
• #4248: Error Multiband start and end frequency
• #5189: Sweeptime is used during final measurement instead of the QP measurement time
• #5216: Test started event log entry should only be added in a restarted multiband test if manual or automatic is pushed
• #5307: Despite of no changes the message "The file has changed, do you want to save changes?" is shown
• #5341: After a Manual Mode change there is undesirable regulation
• #5440: Can't zoom out after maximum zoom in at graph
• #5469: Invalid Device Driver Handle error (Kalmus 727LC)
• #5529: Invalid Device Driver Handle (Virtual) Amplifier
• #5545: Graph is not updated when switching to the second band
• #6075: During instable measurements it may happen that Peak and Quasi-Peak measurements are inconsistent
• #6191: Add an 'Add Test' button to the Sequence window, to simplify the addition of a test
• #6230: Table export only copies the time and frequency data
• #6264: Overlapping bands in MB immunity are tested multiple times when only the modulation is different
• #6352: Changing the activated detector during Continuous Measure clears the measured value of the deactivated detector
• #6449: Frequency range settings are generating an error and the configuration of the TSF is lost when a read only test is saved as new test
• #6452: Frequency array calculation of emission sweep of analyser is missing a step
• #6861: Radiated Immunity Multiband is referring to a receiver
• #6907: Improve autosave functionality that it no longer overwrites the current test data, but first makes a backup
• #7074: Possibility to change polarization of an existing calibration file
• #7077: continuous measure is using sweep time setting
• #7143: RI Multiband only shows Puls when AM is also selected
• #7147: Redoing an already performed test overwrites the previous test-results
• #7167: Amplifier linearity measurement accepted power lines hidden
• #7177: Unable to zoom graph while test is running
• #7203: A generic error occurred in GDI+
• #7214: PI windows still do not fit at full window size using an acceptable resolution
• #7242: Two electrical field graphs are shown. Which one is correct?
• #7247: Prana amplifier is not correctly being put in Operate during immunity test
• #7249: Show example of unit settings
• #7252: RadiMation Free Responsiveness
• #7254: Change Basic small controlling window for PowerMeter
• #7255: Change Basic small controlling window for Amplifier
• #7365: Minimum size of 'Burst' and 'Envelope Tracing' tabs of the VI Powermeter
• #7411: Connection state is still orange while the device is already connected
• #7441: Minimum Form Size is always set to 0,0 at runtime
• #7449: VI Powermeter error lock when removing device
• #7499: RadiMation opening EUT is slow
• #7523: PI EFT Test levels are not covering all the different measurements
• #7575: RadiLog long tests multiple log files.
• #7581: Test description of the test is not visible in the test data
• #7637: Driver: emtest UCS500-M4
• #7644: Filling the EUT information is being slow.
• #7717: Unchanged LLF is asking to be saved when closing the window.
• #7721: System attenuation gain duplicate measurements
• #7737: Report generator query keyword for the table information is not exporting any data
• #7760: Ability to merge multiple Radiated Immunity CALibration files for different frequency ranges into one
• #7768: Wrong frequency at monitoring input events
• #7769: Saving tsf as ReadOnly data lost
• #7773: Incorrect table information for frmVIPowerMeter at the ctlControlGraph table
• #7779: Overlapping bands in MB immunity are tested multiple times when only the modulation is different
• #7796: Compression Gain System Calibration default 1 amount of samples seems to result in a corrupt calibration file
• #7799: Sorting of the ctlFormattableGrid is different when new columns is added
• #7811: Clear button on the VI Fieldsensor doesn't seem to work when the table is shown
• #7812: VI Fieldsensor keeps raising error messages when the probe is turned off before it is disconnected
• #7819: No data document could be created for the test identifier: "
• #7820: Test specific templates are gone after graph customization
• #7824: Reflected power input in Multiband Immunity
• #7836: Connect button is not showing 'Connecting'
• #7842: Saving EUT file with keywords
• #7844: Incorrectly saved Test results starts the test when reviewing the Test results
• #7845: PI test EUT cable selection should be changable while TSF is read only.
• #7866: Corrupt file saving when validator failed.
• #7867: Out of memory when starting RI test
• #7878: RadiLog error report containing # in description gives error.
• #7885: Test data like notes and specific templates settings are updating or overwriting EUT overview settings
• #7886: Resizing of the Graph customization window hides some graph customization controls
• #7887: Missing keyword in Table shifts the table
• #7893: Data file is not saved every 5 minutes, when a final peakmeasurement is busy
• #7894: Radilog memory is not being swapped
• #7896: Missing last test frequency in ReportGenerator output
• #7897: Error Report send not always sending
• #7898: & sign in device driver name is not correctly shown in the EUT Monitoring dialog
• #7902: MessageBox that is shown from the testsite before actions can be shown behind the main window
• #7903: Unable to start RadiMation with incorrectly configured path
• #7904: Default table settings are stored in the user interface
• #7905: ReportGenerator Report and output file selection is not saved.
• #7908: Invalid tsf in sequence can corrupt the sequence
• #7915: Merging of calibration files looses the originally desired fieldstrength
• #7918: Graph customization window can be made too small
• #7922: External modulation should not be possible for a VI signal generator
• #7926: The RBW value has changed by the device from 120 to 100 User description:
• #7927: Duplicate more than 1 test at the same time in the new Sequence window.
• #7932: Very long filenames of the RadiLog file cannot be opened by RadiLog
• #7937: Signal generator VI frequency can be set outside the range of the controlled device
• #7940: Why is the Peak Table disabled during an Emission test?
• #7946: Opening test results directly sets the changed flag.
• #7947: Switching to a different band using 'Continue automatic mode settings' is incorrectly checking if the carrier frequency is valid
• #7950: Ability to hide Report Generator Template column for 'The keyword "" is available in the tempate' window
• #7951: Sending unprintable characters with configurable device driver
• #7953: Frequency list settings are not saved for a sequence and thus not used when Fixed power test is run from within a SEQ file
• #7955: Size of Voltage Dips and interrupts TSF window can be made too small
• #7962: RadiLog to long subject gives error. Strange behaviour occurs.
• #7963: RadiLog parsing fail
• #7964: Directly after installation, the power graphlines are not shown in the VI Powermeter
• #7965: A read only TSF is also asked to save the changes
• #7966: Last View update is being skipped
• #7969: EFT tests with repetition rate 100 kHz (burst duration 0,75ms) can NOT be performed
• #7971: Radilog saving file, file in use while reporting error.
• #7980: Test data files are zero based count on disk which is confusing for end-users
• #8003: Clear graph button for VI windows does not work (when disconnected)
• #8004: Opening of locked files should wait for a few seconds and retry opening locked files
• #8009: Opening a second CE Absorbing clamp test, switches both graphs from log to linear xaxis.
• #8011: Exporting polar graphs contains a white space area.
• #8015: Improve graphical representations of graph
• #8021: When a Band has been selected the TSF is marked as being changed
• #8029: Graphs during Multiband Immunity are not updated during test
• #8030: VI powermeter windows does not work correctly
• #8033: Combine user defined units to prevent multiple equal axis from being shown in graph
• #8040: Error window location cut off
• #8046: Error report, cant write to temporary directory
• #8053: EUT being removed after network reset.
• #8054: Manual frequency is not measured when it is exactly the same as the last frequency in the calibration file.
• #8061: Before actions are prompted multiple times at the end of the test
• #8069: Shortcutkeys not updating ctlEvents
• #8085: Gaps in graph lines.
• #8096: Auto detect peaks shows object reference error
• #8101: RadiLog SQL files containing ";" is not opening correctly
• #8104: RadiMation does not automatically refer and open the latest installed version
• #8106: RadiLog object reference after saving
• #8107: Errors are not reported in RadiMation
• #8108: Error window tooltip causes object reference error.
• #8109: Export full PEAK table
• #8112: Radilog Parsing error when opening log from zip
• #8114: Calibration Files do not use the same calibration method
• #8130: Virtual Instruments infinit loop errors
• #8137: Language files as unicode
• #8138: VDI Impedance is set incorrectly to the device
• #8140: VI Signal Generator all controls are still disabled after connected
• #8144: Exporting graph to LLF in the graph options crashes