Release Notes/Solved items Version 2020.0

RadiMation version 2020.0.12

• #10768: Driver for PMM 9010/60P
• #10895: Issue 2020-04-01AL1_ra emission peak values dropped down in Diagramm
• #10909: Issue 2020-04-09 AL2_ OSD does not show current values of dwelltime in manual mode
• #10926: Change defaults in the stepper.
• #10927: Change default test level for the Calibrated Field Testlevel to V/m.
• #10928: Change default for modulation when you click activate modulation.
• #10933: The reportgenerator keeps searching for keywords in infinite loop when exporting the template directly after test
• #10966: Inn-Co CO 2000 (Unit 1): Not all bytes are written to the GPIB-Board within the timeout period (GPIB: EABO).
• #10971: Issue 2020-04-09 AL2_ OSD does not show current values of calculated field in manual mode.
• #10976: Connection time-out when trying to connect to AR FA 7006
• #10979: Radiated immunity: Modulation and change mode are not displayed correctly.
• #10983: Driver: DARE!! Instruments RPR3006R
• #10989: R&S ESW8 Input 2, pulse limiter activation requires that DC Coupling is selected.
• #10990: Adjust Network Analyser Report Codes VSWR and ReturnLoss.
• #11005: Double click EUT file does not open in RadiMation.
• #11007: Dot and Comma issue when exporting data.
• #11010: Radimation Version 2020.0.011 Radiated Emission Manual - Antenna Factor.
• #11016: Agilent 8753: Specific System Error: 9, "CAUTION: LIST TABLE EMPTY".
• #11018: Antenna tower of Inn-CO CO3000 is not moving when controlled by Ethernet

RadiMation version 2020.0.11

• #10106: CISPR detectors are not selected or not selected correctly - ESU 8 - ESW26.
• #10650: Connection to CARAD not working
• #10659: BONN BLMA 1060-75-50: Add monitor command to the driver
• #10782: Pause Test alwas asks to save after closing it or when the counter is finished.
• #10812: Driver: Frankonia CDNE M2 / M3.
• #10827: Driver: Van veen loop.
• #10838: Polarizer battery empty errors are shown at inconvenient moments
• #10855: TDEM-X26 gets frozen after update driver package
• #10871: Issue 2020-03-26_AL2_mk Messtechnik OSD shows no output
• #10872: Error in RadiLog: Template (VARIABLEREPLACER.OBJ) Copied to:.
• #10874: TDEMI_X26: Specific System Error: -114,"Header Suffix Out of Range; SENS:SCAN4:STEP?
• #10875: TDEMI_X26: No match was found in the specified regular expression.
• #10878: Bonn amplifier is going into a loop
• #10884: Rohde & Schwarz ESW 8 Input 2 Time Domain: Specific System Error: -222,"Data out of range;SCAN1:STOP 1100000000 HZ"\n) using ESW8 Input2.
• #10885: Driver: add Rohde & Schwarz ESW Input 2 driver for powermeter.
• #10886: Driver: add Rohde & Schwarz ESR Input 2 driver for powermeter.
• #10887: Spectrum Analyser (ID1556) Input 2 (LAN): Impossible to get description string for this Error! Probably an unknown RadiMation Error. Code: 1073741975 (0x40000097)
• #10889: RI - Not possible to measure on points
• #10899: Ni cDAQ analog value max +-15 Vdc
• #10901: Temporarily disable the automatic calculation during the generation of an excel report.
• #10919: GTEM-1_SMB-100A: Impossible to get description string for this Error! Probably an unknown RadiMation Error. Code: 805317371 (0x30002AFB)
• #10923: Agilent Technologies N9038A Scanning Receiver: Specific System Error: -221,"Settings conflict; Step Size clipped to nearest value allowed.
• #10929: Rohde & Schwarz ESPI 3 Scanning Receiver (QTR:15): Specific System Error: -200,"Execution error; Function not available; BAND:TYPE NORM
• #10934: R&S ESR 7:Make sure that CISPR average is used in the pre-measurement when "Use CISPR detector is applicable".
• #10973: How to get the values for quasi-peak in my report
• #10978: Running Makro after generating data 2020.0.11
• #10993: Rohde & Schwarz FSV 3 BCI: Not all bytes are written to the GPIB-Board within the timeout period (GPIB: EABO).
• #10994: How to include the markers of an emission test in the graph in a report?
• #10995: How to include the quasi peak limit line values in the emission table in the report?
• #10998: How can measurements for similar standards (CE & FCC) be done only once?
• #11001: Larger variation of field strength in Time graph compared to frequency graph
• #11006: RBW switches from 1MHz (fix) to Auto [120 kHz].
• #11021: How to specify a Current Sensor Correction File in dB

RadiMation version 2020.0.10

• #10605: Frequencies of injection and calibration jig are not remembered
• #10659: BONN BLMA 1060-75-50: Add monitor command to the driver
• #10663: R&S ESU 26 - Execution error function not available;band:type norm
• #10842: Radilog file can't be bigger then 2 gb, after it will create a 0 bytes RadiLog file which can be sent
• #10846: Driver: Electro metrics 6913.
• #10855: TDEM-X26 gets frozen after update driver package
• #10866: Die arithmetische Operation hat einen ??berlauf verursacht.
• #10868: R&S ESCI: please add the option to swich DC coupling to the driver

RadiMation version 2020.0.9

• #10391: Driver: Schwarzbeck NFCN 9734 Switch Matrix Driver.
• #10833: Multiband Immunity graph does not look correct
• #10618: ||TIME; FREQUENCY;.TABLE 30 s|| works in 2017.2.7 not in 2019.1.9
• #10822: Radiated Immunity test doesn't show 1hz steps.

RadiMation version 2020.0.8

• #10646: Driver: Schwarzbeck CDN 801.
• #10647: ErrorReport: "DARE!! Instruments RGN2400A: The requested carrier level is higher than the maximum ( 13 dBm). Limited the set carrier level to 13 dBm. "
• #10769: R&S FPL 1007 - The set value of attenuator is not set in the spectrum analyser. During measurements value is set to 0 dB.
• #10807: Time and Date on the mk Messtechnick OSD are only displayed on output 2
• #10817: Radiated Emission manual mode uses the default unit for field which is defenided at radiated immunity
• #10829: Rohde & Schwarz NRP6AN (1-0944): Specific System Error: -148,"Character data not allowed; SENS1:FREQ 540000000 HZ
• #10829: Rohde & Schwarz NRP6AN (1-0944): Specific System Error: -148,"Character data not allowed; SENS1:FREQ 540000000 HZ
• #10831: Radiated Immunity MB with frequency list file shows incorrect power with hz steps.

RadiMation version 2020.0.7

• #3522: Agilent 8753ES is giving EABO error first time RadiMation starts
• #10521: Checking the driver for R&S NRX indicates that the device is not connected
• #10639: Driver: COM-Power CDN-T8SE (LISN).
• #10640: Driver: Schwarzbeck CAT5 8158 (LISN).
• #10641: Driver: COM-Power ISN T8.
• #10644: Driver: Rohde & Schwarz MDS 22.
• #10645: Driver: Minicircuits TIA-1000-1R8
• #10674: GAUSS TDEMI X - When using a step size of 100kHz the results do not match the results on the analyser
• #10687: Cannot find antenna tower in the currently active testsite .
• #10751: R&S ESW8 Pulse limiter on RF input 2.
• #10763: Formulas in the manual are not displayed correctly
• #10766: D.A.R.E!! Instruments RGN6000A: Setting the frequency raised an error
• #10786: Send Data To RGN2001A switch matrix ATT2 (9KHz-800MHz): Impossible to get description string for this Error! Probably an unknown RadiMation Error
• #10801: mk Messtechnick OSD driver of 2020.1.27.1708 is not sending any comments
• #10802: mk Messtechnick OSD shows random "black spots"
• #10803: Clearing a longer text from the mk Messtechnick OSD leaves the background color set
• #10804: modulation type is transmitted continuously to the mk Messtechnick OSD
• #10806: MK Messtechnick OSD is not cleared correctly
• #10808: Time and Date are always displayed on the mk Messtechnick OSD, even if the checkboxes are unchecked
• #10809: mk-Messtechnik on screen text display driver does not work
• #10816: Only rounded steps are possible when using a logarithmic step size.
• #10821: R&S ESI Powermeter can be improved when very small frequency steps are used
• #10826: Driver: Prana 25 S

RadiMation version 2020.0.6

• #8916: Agilent 33250 as external modulator
• #10365: Driver: TurnTable Siemens XYZ.
• #10426: Radimation callibration does not scale properly anymore.
• #10461: Change device driver names for Dare!! CDN's
• #10476: External 20 dB Attenuation: RS232: Setting the Baudrate attribute raised an error.
• #10484: N9038A: Not able to select more then one trace.
• #10485: Driver: Schwartzbeck CDN M2.
• #10486: Driver: Schwartzbeck CDN M3.
• #10487: Driver: Luthi CDN AF2.
• #10488: TESEQ T2-10.
• #10489: Driver: TESEQ A201A.
• #10490: Driver: Schloeder CDN M2-32A.
• #10492: Driver: TESEQ MD4070.
• #10493: Driver: Tektronix MDO 3014
• #10495: Driver: R&S FPL1000.
• #10501: LUMILOOP LS Probe 1.2: Device Not Connected.
• #10508: Possibility to remove the RadiMation logo from the emission graphs in the report?
• #10526: Driver: Schwarzbeck UBAA 9114
• #10538: Die Sammlung wurde geändert. Der Enumerationsvorgang kann möglicherweise nicht ausgeführt werden.
• #10592: The default port of the RadiCentre LAN is wrong.
• #10595: During rotation of turntable, the tabs on the Multiband test become disabled.
• #10602: Driver: AR JB6.
• #10603: Driver: AR 30S1G6.
• #10607: Driver: Horn Antenna ATH800M6G.
• #10610: R&S ESRP 3: 1st 2 peaks measured is with correct 120 RBW, 3th & 4th are measured with 100 kHz RBW
• #10623: Driver: MultiMeter Keysight 34450A.
• #10628: BBL200 idn check returns Rohde & Schwarz,BBA150.
• #10629: BBL200 Timeouts.
• #10666: Description for this error is not available. Error nr.: 536881313
• #10669: DARE!! Instruments RGN6000B HF (USB): Frequency tried to set is lower than the start frequency (9000 Hz) or higher than the end frequency (6000000000 Hz) of the device driver.