Release Notes/Solved items Version 2020.1

RadiMation version 2020.1.9

#10653: LAN Controlled INN-CO CO3000: Always error during deinitialization
#10688: Teseq NSG 4070-35: RS232: The rs232 runtime data is not created
#10879: No error is raised when the RadiGen is controlled while the interlock is not closed.
#10905: 1GHz: Attenuation set too high
#10996: Error message from the Inn-CO CO3000 during deinitialization of the test
#11161: Transient3000: How to setup the dip angle.
#11162: Transient3000: How to setup the reduced voltage time.
#11184: "DARE!! Instruments RGN6000B: Device returned Error code : 4005".
#11186: Exported average values are wrong.
#11187: Values are exported in linear scale but are expected as dB values.
#11259: Driver: Keysight Technologies DSOX3014T
#11272: Driver: Keysight Technologies N9048B

#10466: FCU 3.0 s: Change the unit labes to reflect the different LD types
#10469: FCU 3.0 s: Make a equipment page and add information to setup in Radimation
#11126: Frequency points are not included in export of limit lines
#11146: The tabs with Peaks, Events and Notes on a Multiband window are not enlarged to the window size
#11148: Maturo FCU3.0 controlled turntable is not starting with turning
#11150: Current measurement is always measuring 500 mA.
#11154: Order of tabs shown on ctlControlGeneralTabs for Immunity and Emission
#11206: Exporting data of multiple bands as seperate graphs

#8673: Printout shows incorrect RadiMation version.
#11102: Out of memory exception when exporting more than 8 test files with the commandline interface.
#11122: System.ArgumentException in clsDocViewController.GetVisibleForms().
#11129: A very high header is used on the printouts

#8833: Default value of tolerance in fixed field test is 0.0 dB, which results in very long test time.
#10593: Order columns is changed when exporting to excel
#11020: Add radilog error messages for empty exception catches.
#11086: PowerDelivery Enabled setting in TUNING.INI is modified when the CONFDVDR directory is changed
#11102: Out of memory exception when exporting more than 8 test files with the commandline interface.

#5337: Partly protection of TSF files.
#8814: Default value of the electrical field strength is too low.
#10252: Also include a graph for the measured impedance in the Network Analyzer EUT calibration.
#10825: RadiMation Emission Burst: When setting trigger to auto then you can't stop the test.
#10931: Error: Access to the path 'C:\TUNING.INI' is denied.
#10937: Zero the field probe when the field sensor is used as an AD Convertor.

#10181: RSRESW8 - Receiver (ID1703) Input 1 [LAN]: More points received from the receiver/analyzer then calculated.
#10647: ErrorReport: "DARE!! Instruments RGN2400A: The requested carrier level is higher than the maximum ( 13 dBm). Limited the set carrier level to 13 dBm. "
#10648: Include the RadiMation version number in the text of the e-mail of the error-report
#10655: Loading an older TSF file, shows the test configuration in readonly mode
#10656: Include a menu entry in the help menu with a link to the available application notes on the RadiWiki website
#10711: update darelang to accept devexpress controls
#10735: Not possible to select 3 dB filters on ESPI3.
#10750: Ampersands are shown in the new ribbon menu
#10753: Drivers: MEB CDN's
#10767: R&S FPL 1007 - Screen is not switched on by default. Have to turn it on manually.
#10769: R&S FPL 1007 - The set value of attenuator is not set in the spectrum analyser. During measurements value is set to 0 dB.
#10770: R&S FPL 1007: non CISPR detectors chosen for 200 hz and 1Mhz.