Release Notes/Solved items Version 2021.2

RadiMation version 2021.2.8

• #3971: Radiated emission multiband: click on "continuous measure" to disable function is taken twice quite often.
• #6698: Project: Improve Continuous measurement method.
• #11553: Underscore shortcut keys are not correctly assigned in field probe setup dialog
• #11604: Text that is shown in progress bar is dark grey, instead of black as in buttons.
• #11612: Binary block buffer retrieval over VISA Socket port is resulting in timeout
• #11687: WriteReadBinaryBlockBuffer causes timeout when TCPIP::x.x.x.x::port::SOCKET is used
• #11742: ErrorReport: "locked the gpib board".
• #11887: Measure time of 10ms is out of range.
• #12053: The device driver system is currently not usable
• #12072: ErrorReport: "Multiband Test one subrange not executed".
• #12082: Schwarzbeck CDN as injection device
• #12083: Include a check during startup to ensure that the Windows decimal separator is not "" (blank/nothing) or "0"
• #12084: Correction file with Frequency unit in kHz only shows half of the graph
• #12106: Send frequencies above 10 GHz to newer RadiSense 10 probes.
• #12108: Control channel selection of the radio dummy/fibre optic link of RFPA
• #12129: RepGen: Using a RunMacro keyword, results in the "" keyword not found event being presented
• #12133: Magnitude graph of S-parameter test shows an additional line going to 0
• #12134: Stop sequence: sequence is not correctly aborted when stop is pressed during a zero operation.
• #12135: Frequency scale is not full span.
• #12141: Resolution of R&S ESIB can be configured but only to 500 points
• #12142: Correction file: graph not displayed
• #12146: Rigol RSA5065A without EMI option can only measure a single trace
• #12160: Provide a configuration setting in the Narda EP600-series to configure the sleep mode time.
• #12173: Virtual Signal generator enables carrier on frequency change.
• #12174: Time-out Spurious emission measurement.
• #12181: Strange error on closing RadiPower driver.
• #12185: Rigol RSA5000 series, should allow to use 0 dB attenuation in combination with preamplifier
• #12186: Rigol RSA5065: When auto preamplifier is selected, it is reported as 0 dB, even though the preamplifier is on
• #12207: Reselect the limitline in the TSF file clears the max value customization of the graph.
• #12208: Driver: Tektronix RSA 306B.
• #12216: Error message that device driver system is not usable after a RadiSense error
• #12223: Driver: Prana IPDR250
• #12224: Driver: Prana CJDR250

RadiMation version 2021.2.7

• #4246: Possibility to insert note in "read only" protected TSF before mesurement starts
• #10935: CI manual mode. Make sure to set the settings of the signal generator when modulation is switched of and on so that this setting is imediatly applied
• #11373: DARE!! Development RadiSense IV: Device returned Error code : 4.
• #11739: Add option in R&S ESW driver to active low noise amplifier (for lower noise floor)
• #11846: Measured differences between RadiMation and PMM software when Testing CE/RE
• #12078: Absorbing clamp Maturo FCU: Function not implemented error
• #12087: Opening test data older than 2021.2.1 results in missing distance data
• #12088: ErrorReport: "RI with rot pos, 1 step, 120 degrees".
• #12091: Build RadiMation 2021.2.7
• #12144: Device driver configuration dialog cannot be shown, due to problem of loading GenericTabbedDialog
• #12147: How to disable the power delivery test, to prevent that generated frequencies are really in order
• #12165: Start Frequency is too low for the selected equipment
• #12211: Ability to use an automatic calkit for the R&S ZNB VNA calibration
• #12217: Agilent technologies U2004A driver problem: Insufficient location information
• #12219: Rohde & Schwarz NRP-Z91: Impossible to get description string for this Error! Probably an unknown RadiMation Error. Code: 805313470 (0x30001BBE)
• #12239: Driver: MTS Systemtechnik KRE-4000
• #12291: Question: Forward power amplifier protection file is not found
• #12293: Error message: There is no average probe selected
• #12295: Incorrect RBW of 1 MHz with QP detector in range 1GHz-6GHz

RadiMation version 2021.2.6

• #11795: Add ability to measure electrical fields of ~ +1000 V/m using a RadiSense
• #12040: Slow start of RadiMation Pulsed Immunity test
• #12064: ErrorReport: fault "System._ComObject"

RadiMation version 2021.2.5

• #11962: Distance unit text is missing in generated reports
• #11965: ErrorReport: "Antenna distance incorrect after upgrade to new version (2021-1-6 -> 2021-2-3)"
• #11988: ErrorReport: "Unable to see cable under test descripton"
• #12050: ErrorReport: "Cannot find positioner"

RadiMation version 2021.2.4

• #11806: RIGOL device driver is measuring too high AVG and QP detector values
• #11962: Distance unit text is missing in generated reports
• #11965: ErrorReport: "Antenna distance incorrect after upgrade to new version (2021-1-6 -> 2021-2-3)"
• #11988: ErrorReport: "Unable to see cable under test descripton"

RadiMation version 2021.2.3

• #9170: Some properties set in the polarGraph init function get reset when the graph is actually drawn
• #11892: Before/After actions Pauze window does not close it self, or by clicking the OK button.

RadiMation version 2021.2.2

• #11851: Minimum absorbing clamp distance is 1 mm. This should be changed to 0mm.
• #11854: Final measurement stops after first final measurement if distance graph is selected.
• #11855: If the default graph configuration is set to logarithmic, a strange x-axis is shown for distance graph
• #11856: If distance unit is set to cm, the frequency too high errors are generated in the distance graph
• #11857: The unit configuration of the distance is not used in the graph x-axis
• #11858: Limit line in the distance graph is shown as a curved line. This should be a straight line in the distance graph.

RadiMation version 2021.2.1

• #2273: Multiband Conducted emission absorbing clamp
• #5579: Stopping a sequence is almost impossible