Release Notes/Solved items Version 5.4

RadiMation version 5.4.16

• #3140: Dip in stress test while doing imm. test

RadiMation version 5.4.15

• #3328: Changes to the description of the limit line doesn't mark the file as changed
• #3325: Add a limit line in a MB TSF file takes 15 seconds
• #3210: Ramp is not correct for certain frequencies, it either does not ramp or ramps first down and then up again

RadiMation version 5.4.14

• #3321: Pulsed report generation is not inserting several key words.

RadiMation version 5.4.13

• #3309: Every time the menu Configuration/Configuration is open, the information of the report format (doc, xls) previously defined is not retained and is set again on excel report.

RadiMation version 5.4.12

• #3274: Administrator is the only person who can change the configuration.

RadiMation version 5.4.11

• #3243: Gtem measurement has jump at 500 Mhz with 10 Meter oats correlation
• #3200: The wrong sequence is taken for the MB test
• #3079: Manual doesn't describe the used algorithms in the 16 point calculation
• #3047: We didn’t get the VSWR displayed! How to set it up?
• #3046: How can a test be continued from a different frequency?
• #2704: Driver R&S ESPC B2 not available
• #2483: Advanced DUT monitoring and checking limits with TDS 544A
• #2400: Changing frequency range for ESPC (starting at 9kHz)
• #1667: Automatic determination of amplifier saturation during 1 point RI calibration
• #1544: Circulair emission diagram

RadiMation version 5.4.10

• #2582: List of performed tests is not sorted anymore
• #3233: Sorting and deleting tests is not working correctly for 5.4.9
• #3234: Graph and time bar CI subst does not continue after the manual mode

RadiMation version 5.4.9

• #2043: PDF printing does not always correctly
• #3229: 5.4.8 has screen update problems

RadiMation version 5.4.8

• #3217: Rohde & Schwarz SMR does not respond to *OPC? if the set carrier level is below the minimum
• #3216: Rohde & Schwarz SMR signal generator does not respond on *IDN? query
• #3215: Silent installation complains that not a correct DriversDir is specified during the device driver installation
• #2113: Keyword CALIBRATION FILE does not work with RI subst test reporting
• #3204: Suggest that Delete Peaks is moved away from Peak measure to avoid accidental deletion.
• #3175: Driver: Fieldsensors
• #3138: Error Message during deinitialisation of MTS KRE
• #3129: Driver: USB driver for the Bonn BLWA0810-160/100D and the BLMA1080-60/35/20D
• #3128: Driver: SMF100A Signal generator controlled over USB
• #3103: Testlevel below 100 dBuV for constant voltage is not allowed.
• #3051: Our turntable has an angle of +200 and -200, I set the start angle to -90 and end angle to 180 and 4 steps. But did doesn’t work.
• #3030: Pass/fail in CE multi band is not determined correctly.
• #2987: It is not possible to select the name of the test engineer in Multiband
• #2986: The name of the test engineer (and other information) cannot be specified during the sequence
• #2893: R&S SML 01: Timeout while waiting for OPC command
• #2755: Can not input a lower than 1% input for logarithmic sweep steps
• #2738: Problems during deinitialisation of MTS KRE

RadiMation version 5.4.7

• #3183: Crash of RadiMation Vers. 5.3.18 when CARAD driver is included

RadiMation version 5.4.6

• #3181: Error message during read out of Fluke 8846A (Fluke 45 command set)
• #3179: Driver: Schwarzbeck NTFM 8134
• #3177: AD Channel with a 'dBm' unit, is not shown on the same axis as a power-meter with the 'dBm' unit
• #3174: Driver: Cal jigs
• #3173: Drivers: Injection devices
• #3172: Driver: Couplers
• #3171: Driver: Amplifiers
• #3163: HP 33120 signal generator raises an error and beeps during initialization
• #3155: Not all devices are checked for the frequency range
• #3149: OATS test is displayed but not selectable
• #3139: The proposed EUT filename, in Save As EUT, has all \ removed
• #3137: ESU-40 preamp driver issue.
• #3135: Writing IPersistable files with a 1 MByte cache are stored corrupted on disk
• #3133: dBpT/uV factor is not taken into account in the magnetic field test
• #3132: HP83620A is going first to 0 dBm and then lower
• #3123: Filling the Testlevel in dBuV will cause the value to goto either 100 or 180 dBuV
• #3119: The reference level is not reported correctly in the Mil std magnetic measurement
• #3118: Limit line is not displayed correctly when swapping from log to line view
• #3089: Isotroop is dutch. In english it is: Isotropic
• #3087: Manual contains a statement that a field/current check is done during the test initialization. This is not true
• #3056: the property "RadiMation Version" in the Carad driver is left empty.
• #3037: ESU is slow with getting the data back in time domein scan
• #3013: English spelling error in a menu item
• #2993: Saving a immunity multi band file is very slow
• #2956: Auto attenuator and ESU analyser driver doe not work
• #2883: The Add /edit /remove buttons on the AD channels are not the same / are not positioned the same as the other add/edit/remove buttons
• #2882: The buttons on the EUT window section Cables do not have the same pictures as the EUT information items
• #2859: product standard and basic standard in the configuration window does not support enter and delete button
• #2858: product standard window does not support enter and delete button
• #2788: Switch matrix so switch the filterbox inside the amplifier
• #2224: Not possible to select two or more product standards for an EUT
• #545: Customer Database interface should also be able to search on customer name
• #341: The antenna cannot be polarized automatically in an immunity test

RadiMation version 5.4.5

• #2491: The EN61000-4-3 2006 field uniformity calibration does not support less then 16 points while the standard does specify this
• #2791: Rename 16 Point calibration to Uniform Field Area (UFA) calculation
• #3039: The NRP-Z driver needs to changed so the used R & S Layer is unloaded correctly
• #3044: RI multiband ALL graphs key word does not work.
• #3054: Driver: Metrehit Bd 232
• #3055: Carad driver is sending humidity and temp twice.
• #3076: When for "Auto (10 dB)" is selected for the attenuation, the receiver is switching unnecessarily to 20 dB
• #3114: external test results can not stored in the 5.4.4 version
• #3121: The RI minimum performance test is reporting information changed when only the tsf is opened.
• #3122: CI cal config window is reporting changed when opening the tsf

RadiMation version 5.4.4

• #2994: CI EM Clamp virtual mode test errors
• #2995: HP 8547 incorrect input selected (driver issue?)
• #3106: The country of a customer cannot be retrieved from the MySQL databse by using the customer database interface
• #3107: It is not possible to search on the customer name when an ODBC customer database driver is used

RadiMation version 5.4.3

• #1216: Customer database device driver for Microsoft Excel
• #1260: ODBC Excel device driver for customer database
• #2934: Cal jig, Teseq PCJ9201B
• #2937: Mysql support by RadiMation
• #2943: Driver: injection device
• #2971: Setting the puls setting to 0.5 uF is not remembered in the test.
• #2972: The report generator should remember the last template document that was used.
• #2974: CARAD driver is giving wrong error description
• #3093: CE Multi band test is not displaying all the results just the first and the last band

RadiMation version 5.4.2

• #3105: MySQL ODBC driver version 3.51 is not working correctly with RadiMation
• #3075: When a frequency has been re-measured the result is shown graphically on the plot with what appear to be a higher resolution
• #3071: On emissions graph it reads dBuV and not dBuV/m depending on radiated or conducted
• #3069: Control of the turntable is not working correctly
• #3066: driver for LeCroy 9310AL
• #3065: Why isn't average field data supplied during field probe calibration (X,Y & Z axis measurements are) at D.A.R.E!! Calibrations? What does Radimation require for calibration data?
• #3058: HP 437B is not going up till 18 GHz.
• #3042: Clicking Combo box in the Test site leaves the combo box empty
• #3036: PMM 9030 driver has problems during the init of the device.
• #3024: Settings.ini warning should be removed for win2K and up
• #3021: CARAD Driver is missing the probe information
• #3016: It is not possible to not use the polarization function of a RadiTower controller
• #3015: overrange of RadiPower is not detected correctly
• #3012: the mode of operation is not inserted in the multi band emission test print out
• #3010: R & S SMY 01 embedded version 1.10
• #3005: Error message is giving wrong device in bci subst test, antenna instead of injection device
• #3004: HI 4422 device driver crashes, when it is being initialized
• #2991: opening another tsf file does not trigger a save function of the current document
• #2990: The surge/esd/eft tabs do not change when you open another tsf file
• #2988: A sequence of CE measurements crashes
• #2985: Deleting a test from the EUT window raises errors that the test cannot be renamed
• #2963: Crash when the R&S ESHS30 receiver is initialized
• #2951: Radiated Emission Manual Mode (Multi Band) division by zero run-time error
• #2941: Driver: Antenna tower + turn table controller
• #2940: Driver: Atenna drivers
• #2930: limit line does not show during the merge function
• #2916: Radimation crashes with two R&S Z91 USB Power heads
• #2844: configuration window of the HP 34401A is showing the wrong max values
• #2783: Driver: Switch matrix
• #2769: Crash when sending command to gigatronic 8541C device
• #2744: ESMI driver is generating an error that the srq is raised by another device during the init of the device
• #2723: Drivers.exe does not check if RadiMation is still running.
• #2594: Sieple driver for turn table and antenna tower is crashing at de-init of the test
• #2570: EMR200 only working up to 3 GHz instead 18 GHz
• #1959: Software needs a long time to start, due to initialization of not connected amplifiers

RadiMation version 5.4.1

• #2101: Upgrade to use the latest version of the Gigasoft ProEssential graphs
• #2175: Polar plot and height plot in Radiated Emission to show the emission versus the angle and height
• #2301: Marconi is giving waiting for *opc from time to time.
• #2506: RE manual mode, Markers are shown behind the trace
• #2587: 120 kHz RBW filters are not selected correctly for R&S ESU
• #2846: Use the possibility of the R&S SMR to level the carrier level on 0.01 dB
• #2891: Driver: R&S UP300
• #2907: R&S URV5 can not be configured as AD converter
• #2924: Merge window can not be maximized
• #2933: Driver Lisn r & S ENV216
• #2935: Driver: Fcc-801-AF8
• #2936: Tektronix TDS 544A: surpress error message
• #2938: exporting table to excel is giving an additional column

RadiMation version 5.4.0

• #3217: Rohde & Schwarz SMR does not respond to *OPC? if the set carrier level is below the minimum
• #2921: Combined Graph Report generator code is not replaced if the first mentioned graph is not available
• #2912: TSF configuration file is opened when you click the close button in the titlebar
• #2895: Esai does not get the trace in the screen
• #2886: Current is not displayed correct
• #2873: Saving a TSF with a ':' in the name is raising errors
• #2856: The attenuation of the current sensor is not corrected the right way when configured as attenuation.
• #2855: filter settings for the RadiSense does not work for above 4.53 in combination with serial communication
• #2790: Wrongly measured reflected power during BCI-(fixed current)-tests
• #2787: Manual measuring Field sensor
• #2761: Wrong polarisation at the first measurement
• #2593: Adding correction to the signal generator is not taken in to account during fixed power testing
• #2402: removing item from general info does not refresh the list and confuses the end user
• #2275: Emco 1090 and multiband is going up and down
• #1910: configurable table for emission measurement in the report generator

RadiMation version 5.4

• #2977: Selected probe in configuration window of AR FM7004 device driver is 'off by one'
• #2865: Gray background of a graph (instead of white colour) after exporting a changed graph
• #2717: Limitation of current during BCI test (FIAT standard)
• #2634: Different password/user management
• #2591: Quasi peak trace graph is drawn behind the peak trace graph
• #2453: Strange results in CE / Question to CE
• #473: The end-user doesn't change anything, but still the software wants to save the file