Release Notes/Solved items Version 5.6.0

RadiMation version 5.6.0

• #420: Option to limit the power in a conducted immunity substitution test, based on the calibrated forward power
• #421: Configurable device driver for reading out an AD-convertor
• #954: Step frequency in RE test
• #1302: EMI test with log. Frequency steps
• #1741: PSA limit not the only one describing power limitation on forward power calibration
• #1803: Device driver for AR 500W1000 is conflicting for different end-users
• #1811: Switch matrix device driver for the HP 3488A
• #2145: Amplifier is switch in POWER OFF after BCI test
• #2450: Changing description 'PSA-Limit' to 'Power Limit' in BCI
• #2538: Not possible to level on the current in CI substitution manual mode
• #2699: During a 'Check' for a device, all the other controls should be disabled
• #2774: Question to CE measurement (problem with accuracy of detected peak)
• #2881: Driver: Advantest R3131A as powermeter
• #2925: Driver for Yokogawa Oscilloscope DL1740
• #2929: A small misspell in the CE test.
• #2957: RadiSwitch 6 port does not have an option to not switch the relay
• #3111: How to level on the current during BCI substitution tests?
• #3178: 500W1000 is not switched to OPERATE in version 5.3.18
• #3182: RadiMation sets Anritsu 2623B to wrong settings
• #3185: Driver: SUNOL CONT94
• #3231: 150A400 "needs" a reset command when leaving manual mode
• #3248: Selecting square wave AM modulation does not change the waveform on the Agilent 83640B, and it doesn't raise an error
• #3264: Speaker of the HP 8591E analyser is sometimes activated
• #3318: files are getting bigger, customer can't open them anymore
• #3320: wrong remeasured frequencies in Radiated Immunity (singleband)- Manual Mode
• #3334: Peak not detected when zooming in Multiband Emisson graph
• #3337: How is the Ramp in Mult. Im. configured?
• #3338: Problems starting Cond. Im. Multiband
• #3379: Final measurement with QP detector using a PMM 9030 receiver results in a software crash
• #3391: Clean install crashes when opening device driver configuration window
• #3392: clean install sets the configuration directory incorrectly to Radimationconfdvdr
• #3399: HP8657 signal generator driver does not support 400 Hz AM.
• #3405: Rs-232 support for the configurable switch matrix
• #3406: signal generator sml03 sometimes is not responding to opc?
• #3408: Driver FC03, turn table and antenna tower controller
• #3413: Carad driver is reporting mcItestData is nothing
• #3416: AM modulation indication on the HP 83630 is not activated
• #3417: Using the ESU tracking generator as a signal generator for the attenuation measurement
• #3422: PSA preselector need option to set the preselector off so that you can measure above the 1 GHz.
• #3426: Driver: Agilent 87405C pre amplifier
• #3428: Driver: HP 59307
• #3426: Driver: ESV-Z1 VHF Current Probe
• #3430: Driver: LISN PMM L3-64
• #3431: Driver: ENI 603L and 411LA
• #3432: Driver: Solar 9142-1N and 9719-1N
• #3433: Driver: EATON 93686-8L and EM test HFK
• #3437: LISN ESU User port
• #3438: TDS220 is only available as an AD convertor not as an oscilloscope
• #3448: Conducted Immunity Fixed Current with activated performance threshold is crashing
• #3460: Format string does not work correctly with %lf and a double.