Difference between revisions of "Rohde & Schwarz FSEK 30"
DevicesBot (talk | contribs) (Updated DeviceDriverInfo template) |
DevicesBot (talk | contribs) (Updated DeviceDriverInfo template) |
||
Line 2: | Line 2: | ||
|DLLFile=RADRSSA.DLL | |DLLFile=RADRSSA.DLL | ||
|DeviceBrand=Rohde & Schwarz | |DeviceBrand=Rohde & Schwarz | ||
− | |DeviceDriverName= | + | |DeviceDriverName=RSFSEK30P |
|DeviceType=FSEK 30 | |DeviceType=FSEK 30 | ||
− | |SupportedDeviceTypes= | + | |SupportedDeviceTypes=8 |
}} | }} |
Revision as of 20:51, 12 February 2020
The Rohde & Schwarz FSEK 30 device driver is a Power Meter which is supported by RadiMation®.
Configuration
The following tabs are available in the advanced configuration of the Rohde & Schwarz FSEK 30:
![]() |
Wait time before starting the measurement-loop. Can be used to wait for a signal generator, and or amplifier to stabilize. |
![]() |
The minimum amount of measurements in the measure loop. Continues to loop even if power level is stable. |
![]() |
The wait time between each measurement is taken, during the measurement-loop. |
![]() |
If the measured power between each measurement in the measurement-loop, is less than this value. The measured power is stable. The measurement-loop will then stop. |
![]() |
The maximum amount of measure times, for the measurement-loop |
According to these settings, RadiMation® will perform a minimum of 3 power measurements with a wait time between the measurements of 75ms. If all those 3 measurements are within 0.1 dB, the power measurement is assumed to be stable, and RadiMation® will continue to average of the last 3 measurements. If the difference between the measurements is larger than the specified 0.1 dB, an additional power measurement will be performed, and the last 3 samples will be compared to the 0.1 dB difference again. At most 10 measurements will be performed if the difference between the 3 samples will not be within the specified 0.1 dB.
Both for the leveling, and the monitoring these settings can be set individually. The leveling is used, whenever RadiMation® is measuring the power, to regulate the signal generator. If the powermeter is only used as input, without regulating on it, then the monitoring settings are used.
More detailed information on how to achieve a fast and stable power measurement is available in Application Note 106: Powermeter parameter configuration.
The frequency range of the Rohde & Schwarz FSEK 30 as provided by the manufacturer is shown and selected as default. It is possible to overrule these frequencies and to manual adjust the allowed frequency range of the Rohde & Schwarz FSEK 30.
![]() |
If the checkbox is checked, the default start frequency will be used as the lowest usable frequency in a test for this device. |
![]() |
If the checkbox is checked, the default stop frequency will be used as the highest usable frequency in a test for this device. |
Specifying a different frequency range can be useful if for example:
- A device (like a coupler, antenna, injection device, cable, etc...) is still useable (but out of specification) outside the standard suggested frequency range.
- An external mixer is used to measure an extended frequency range.
- An up- or down-convertor is used to shift the frequency range.
- A newer model of a device is present that has an extended frequency range, and still uses the same remote control commands.
Be careful changing these setting as RadiMation® is no longer able to verify if the Rohde & Schwarz FSEK 30 is used outside frequency range that is specified by the manufacturer. This may result to serious damage of your measurement device.
The settings on the Reference tab influence the measurement frequency that is communicated to the measurement device. The frequency that is forwarded to the measurement device can for example be used by the device to perform the measurement on the correct frequency, or use the correct internal frequency dependant correction or calibration factor on the measurement result. Normally it is desired that the measurement frequency is the same as the carrier frequency of the signal generator. In some situations it can however be required to communicate a different frequency to the measurement device. In such a situation the settings on the Reference tab can be modified.
![]() |
Selects that the actual carrier frequency of the signal generator is communicated to the measurement device. This is the default behaviour. |
![]() |
Selects that a fixed frequency (independent of the signal generator carrier frequency) is communicated to the measurement device. |
![]() |
The fixed reference frequency specified in MHz that is communicated to the measurement device, when the Fixed reference frequency option is selected. |
Related pages
Links
- Google search: Rohde & Schwarz FSEK 30
- Google image search: Rohde & Schwarz FSEK 30
This information about an equipment is automatically generated from the list of supported device drivers from RadiMation. |
If you need more information you can contact radimation-support@raditeq.com. |