Release Notes/Solved items Version 2015.3
Jump to navigation
Jump to search
RadiMation version 2015.3.5[edit]
- #2848: Regulated testlevel should be above requested testlevel if testlevel could not be regulated within the tolerance
- #3962: A limit in a Multiband CI test is only checked when power is limited by amplifier limitation
- #3963: Ramp method in CI Multiband doesn't remeasure the generated voltage
- #4264: Field level is less than set
- #5371: Initialization of Prana AP32 DR216 Amplifier is always successful
- #5978: Driver: Prana DT70D Amplifier
- #5988: Driver Teseq ITS6006 for IEC61000-4-3 & CISPR11 as Signal Generator
- #6134: Driver: Teseq ITS6006 for IEC61000-4-3 & CISPR11 as Power meter
- #6214: Driver: Prana DP600 amplifier
- #6253: Driver: Prana DT70S amplifier
- #6288: Driver: Prana UX55 amplifier
- #6318: Driver: Prana SV70D amplfier
- #6319: Prana LT320D amplifier doesn't work
- #6358: RadiField and RadiGen doesn't switch to local at the end of a test
- #6374: Driver: Prana MT700 amplifier
- #6396: NI DAQ USB 6218 AD Converter read values are delayed
- #6425: Driver R&S NRP-Z91 controlled by SMB100A using USB
- #6460: Driver: Prana MT400 amplifier
- #6489: Check if the HI-6005 fieldprobe is working correctly in combination with the EPI1001A
- #6625: Driver: Frankonia EFS-10 / EFS-100
- #6641: Driver: Control the polarization on the antenna using an RadiCentre external relais card
- #6662: Virtual Instrument for the field strength sensor
- #6712: Switch the external 40 dB attenuator used with Keysight 33521B
- #6777: Amplifier Linearity / Uniformity test different result at 1 -6 GHz
- #6787: Agilent 4403B Spectrum analyser Device Not Connected error
- #6863: Explanation for the use of correction factors for a Current sensor
- #6864: DVDRSYS.DLL cannot be loaded anymore from new device drivers
- #6886: Driver: Bonn Elektronik BLMA 4060-40
- #6901: How to create a correction factor using the unit of transfer impedance in dBOhm
- #6909: Why is a window with a description and value text is shown during the test?
RadiMation version 2015.3.4[edit]
- #1151: Minimum performance level fixed field
- #1881: Graphs for applicable signal/forward/reflected/net power need to be added if a related input is measured
- #1945: Generated Power in Multiband immunity is not limited by the allowed range that is configured the AD Channel
- #2869: Multiband test does not allow the user to select only the reflected power meter as an input
- #3605: Multiband minimum performance is not possible
- #4090: RI multiband minimum performance not working
- #4576: Auto ranging of the HI422 is not working correctly
- #4821: Driver: Tektronix 3000 for fixed voltage test
- #4873: Wrong reading of TDS 3054B scope
- #5323: Pre measurement detector suddenly turns other detectors on or off
- #5572: Use maximum performance level as new start level at next frequency
- #5880: Button to show overview of Calibration Expired (activated) devices
- #6125: Possibility to set the used type of average detector
- #6163: Configurable AD converter measurement always returns zero
- #6233: Control the oscilloscope Tektronix TDS 2000 Series by USB
- #6268: Specify CW instead of NONE, if no modulation is applied
- #6385: Add report generator keyword which only outputs the date
- #6631: Driver Polarization of the RadiField
- #6640: Driver Configurable antenna tower device driver to control polarization
- #6712: Switch the external 40 dB attenuator used with Keysight 33521B
- #6716: How to configure the increase of the power during regulation?
- #6731: Allow that the available columns for the device driver can also be selected in the testsite configuration window
- #6737: Driver RadiField 2003A/2006A/2003B/2006B
- #6738: Windows 10 USB drivers for Radi-products
- #6739: Hide the white area in the Virtual Instrument window
- #6742: Agilent N9038A Average measurements taking longer than expected
- #6762: Ability to select another detector in the R&S ESI powermeter
- #6763: Using the R&S ESI 40 scanning receiver as a powermeter raises the error "BAND:MODE:FFT OFF"
- #6764: Tektronix AFG 3252 Timeout while waiting for *OPC command
- #6770: RadiField errors from the RadiCentre are not raised
- #6771: RadiField Polarization driver should have 'ignore height change' ticked by default
- #6774: R&S NRP-Z55 returns a -10000 dBm value when the powermeter returns a 'NaN'
- #6779: How to perform a Radiated Immunity MB threshold level test
- #6789: VSWR testlevel is not shown in the TestLevel inputs box
- #6794: Multiple tests with same TSF name difficult to include in RG
- #6801: Graph customization settings are not used during printout
- #6806: A lot of 'Handles' are used by RadiMation
- #6809: Can't find device driver for RadiField 1009B
- #6812: Add new Reseller to the Sentinel Key program for Dongle programming
- #6819: Tektronix TDS2024 is not correctly controlled
- #6835: Can deleted measurements be recovered by RadiMation?
- #6836: Is Windows 10 supported?
- #6838: How to see more details of the tweeted improved RadiMation functionalities?
- #6848: RPR3006W is not showing powermeter values when used as virtual instrument
- #6858: RadiLog ReportError should include the RadiMation global event log of that process
- #6867: Is it possible to add more than one amplifier to a test site?
- #6881: Is the device driver for the R&S NRP-Z51 powermeter available?
RadiMation version 2015.3.3[edit]
- #2550: Menu option that starts NI I/O Trace
- #5091: Debugging of device drivers through DDLOGGER.DAT should be simplified
- #5693: Driver: Agilent E7402A Spectrum Analyser
- #6008: Possibility to temporarily disable system error checking in a device driver
- #6119: Error that the frequency of an already used testsite is not suitable
- #6384: How to use the R&S ESCI 7's built-in pre-amplifier in 30MHz-1Ghz range
- #6400: Driver: IFI ST181-10 Amplifier
- #6435: Is it possible to change a correction of an already performed MB emission test?
- #6445: Keywords ||DATE MEASUREMENT|| and ||SETUP TYPE|| do not work anymore
- #6447: Slow powermeter measurement of the R&S NRP Z91
- #6533: PDF version of the RadiMation manual is 55 MB
- #6551: Enables users to easily send Error Reports with RadiLog
- #6553: Add RadiLog messages to the R&S NRPZ powermeter device driver
- #6567: Include a menu entry in the main menu to start the RadiLog
- #6597: R&S NRP-Z91 cannot be used in Powermeter Virtual Instrument
- #6598: Checking a R&S NRP-Z91 takes forever when it is not connected
- #6608: Add RadiLog messages to the USB HID device stream
- #6653: Sending an error report causes an error report
- #6655: Output parameters are not shown in RadiLog
- #6658: Updating Error Report Window
- #6659: Added button to ReportStauts error in RadiMation
- #6666: Driver Teseq PMU 6006 powermeter
- #6721: Not possible to measure the average field probe value during Multiband
- #6722: RadiLog crashes with a 'startIndex cannot be larger than length of string'
- #6778: More lines are included in the graph in a report than requested
- #6784: “hot-key” to export the numbers from the harmonics + linear graph EUT-Calibration module
- #6823: Do I need correction files in RadiMation for powermeters?
RadiMation version 2015.3.2[edit]
- #1106: Directory names in the configuration should be shortened if they don't fit in the listview control
- #2731: Address information of the customer, manufacturer and test-site should be able to be copied from or pasted to the clipboard
- #2860: The amplifier control window is displaying nothing if no items are inserted
- #4538: Turn during measurement explanation
- #4805: Data export from menu REPORTS-EXPORT is not working
- #5692: Driver: 3115 Double-Ridged Guide Antenna
- #5877: Proceed to include some proposed wiki pages for inclusing in manual
- #6071: Very slow band switching in Multiband Immunity (Levelling problem of Power Delivery Test)
- #6277: The 'cancel' button should not be shown when an engineers is removed
- #6283: Broadband units (like dBuV/m/MHz) are not possible for traces
- #6438: Default frequency range of the EMCO / ETS-Lindgren antenna 3117
- #6512: Use the Microsoft Visual Studio 2015 compiler
- #6521: Amplifier Linearity test requires an antenna in the selected testsite for Conducted Immunity
- #6546: New device drivers is raising Description for this error is not available error 536879923 during startup
- #6548: Minimum supported Windows version should be changed to Windows 7 SP1
- #6585: NRP Z55 zero operation took longer than 60 seconds error
- #6588: RegisterDeviceDriver too slow. It takes a second.
- #6605: Is the Ines USB-GPIB-2 card supported?
- #6606: Is the Prologix GPIB convertor supported?
- #6610: R&S ESRP 7: Not all bytes are written to the GPIB-Board
- #6645: How can I set the resolution to logarithmic stepsize?
RadiMation version 2015.3.1[edit]
- #3324: Linearity check for calibration (16 points, 5.1 dB down)
- #4690: Language error: initialisation successfull <=> successful
- #4772: Add a 'Pause' as a possible action
- #5004: A warning should be shown if the AD-Channel maximum and minimum are the same
- #5250: Change format of graph export per default
- #5513: Directories configuration of latest version is interfering with older RadiMation version
- #6168: Harmonic Graphlines have unlogical names
- #6190: Add a general notification icon on all the Multiband configuration windows
- #6193: Change the 'Change' button to 'edit' including a picture button.
- #6196: The Version number in the shared Libs DLL's are not updated
- #6197: Add a 'Remove' option in the right click menu of a device in the TestSite configuration window
- #6201: The table with measurement data is not shown when the Harmonic test data is opened
- #6242: Adding a 3rd amplifier to the amplifier control panel does not update the amplifier control panel correctly
- #6292: Rename tabs on the testsite configuration: 'Standard 1' to 'Devices 1' and 'Standard 2' to 'Devices 2'
- #6300: Enhanced Status Window parameters are not shown
- #6326: Add more low baudrates: 1200, 600, 300, 50 Baud
- #6335: 'Advanced Information' window should be renamed to 'General Information'
- #6357: Regex returns 0 for notations with a space between +/- sign and the actuall number
- #6401: Configurable Amplifier should have wait options after sending power on (for warming-up) and off (for cooling down)
- #6408: Amplifier Slope verification for Conducted Immunity
- #6455: Warnings related to wxEXPAND are shown when a wxWidgets dialog is shown
RadiMation version 2015.3.0[edit]
- #5999: Mark the 'Continuous Measure' button in a different color when it is activated
- #6295: When note window is opened the focus or cursor is not set to the text field by default
- #6368: Duplicating more than 100 tests in a sequence takes a long time
- #6369: Duplicating a test in a sequence file, doesn't mark the sequence file as changed
- #6370: Radio buttons of Conducted Emission Manual Mode traces are swapped
- #6387: It is not possible to select multiple peaks and therefore needs to select peaks one by one
- #6388: Adding new peaks is resetting the peak lists selected column information