Release Notes/Solved items Version 2023.1
Jump to navigation
Jump to search
RadiMation version 2023.1.6[edit]
- #13580: EP600 times out if the binary data returned contains a new line character
- #13666: Provide a more generic 'attenuator' and 'pulse limiter' device driver
- #13674: EMI Schaffner SCR3502 measures high peak values while measuring in the noise
- #13692: Invalid message when removing input from TSF
- #13709: TDEMI Cancel don't work in remote control
- #13744: Logging mode is not supported by this powermeter.
- #13748: Singleband Conducted immunity fixed voltage checks for a CI mill cal data document
- #13756: Include check in firmware update if RadiLink is connected to the external power supply
- #13768: Fixed step count stepper, only tests the first and last frequency of a band
- #13799: Graphline customizations are not remembered
- #13806: Signal power is sometimes empty in RI MB test result
RadiMation version 2023.1.5[edit]
- #13614: Firmware update of the RadiLink RLK3086R is not working because of differences in the software update protocol
- #13641: Automatic retrieval of Temperature/Pressure/Humidity sensors during start of test
- #13686: Table header are not included and symbols are not inserted into reports
- #13699: Connection Check Fail for Keysight N9038A
- #13707: SV: RadiMation object null reference error when using the export functionality
- #13716: RadiCentre version check Driver
- #13720 Test Keysight IO viFLush returning buffermask of value 128 using pre-release build
- #13721: Error in communication with Power meter
- #13723: When a RadiPower USB is unplugged from the PC, no error is shown in RadiMation
- #13727: Set the termination on read for the EP600 field probes
- #13728: EP601 Does not return correct field when using as ad input
- #13732: Amplifier goes in operate before zero off probe
- #13733: Correction of ep601 at 60 kHz is sent as 50 kHz
- #13751: Time out problem with the "EP 601" field probe
- #13782: RGN connection issue in USB controlled RadiCentre
RadiMation version 2023.1.4[edit]
- #8156: Auto discovery of RadiPower powermeters through the RadiMation device driver system API
- #11578: New directory name / description not remembered
- #12860: TSF file directories names are changed to "new directory-<index>"
- #13182: Driver: RadiPol antenna tower
- #13211: FPC1000 using the 'GTEM' test results in "Specific System Error: -113,"Undefined header" when selecting zero span
- #13236: Turn table angle in MK Messtechnik OSD
- #13248: Object null reference error during Radiated Immunity test while determining the input identifiers of the test level
- #13343: Multi-axis field probe read out
- #13375: Creating a sub TSF Directory with a new TSF file (network) results in an empty directory name with the file in the root directory
- #13410: Add a manual controlled XY positioner driver
- #13519: Windows error 128: There are no underlying child processes to wait for
- #13537: Radimation data storage error during test
- #13553: Issue 2023-04-04 AL3 Configuration AD-Converter Keithley (Scanner)
- #13564: Frankonia FC05 Polarization controller issue
- #13567: Update wxWidgets to 3.2.2.1
- #13577: Possibility to switch The FFT mode of the TDEMI
- #13582: Emission Graph as polar plot of angles
- #13594: Rohde & Schwarz SMB 100B: Not all bytes are written to the GPIB-Board within the timeout period (GPIB: EABO)
- #13595: Create a python module for an EUT Status interface
- #13600: Magnetic field test according ISO 11452-8 using CWS500N3
- #13603: Driver: RadiLink RLK3086R
- #13615: How to measure an ADC during singleband tests
- #13616: AD-Converter Keithley (Scanner) the first measurement returns 0V which is incorrect
- #13628: Final QP-Measurement not working for more than 1 Pre-Measured Peak due to the RBW being changed by the device
- #13633: Extend TCP/IP status interface to allow passing of TestInfo.
- #13639: Driver: TDEMI M7/M7+
- #13642: 'device driver function not implemented error' during Radiated immunity Calibration
- #13643: Name of new sub-folder in TSF selection window is lost
- #13644: Cannot execute isotropic field measurement using XYZ axis correction data
- #13647: CI test is levelling down with NSG 4070
- #13655: Rohde & Schwarz SMB 100A fault: Not all bytes are written to the GPIB-Board within the timeout period (GPIB: EABO)
- #13656: RadiPol 2010A cannot control tower height
- #13657: Antenne toren
- #13658: List FSA as 'FS Antennentechnik'
- #13659: single band external modulation depth setting
- #13660: Create antenna tower driver for the RadiPol
- #13661: Auto detect the RadiLink RLK3086R
- #13662: Attenuation/Gain system calibration cannot be used with carrier level below -50
- #13664: IF overload
- #13670: Radisense IV & Dare RSS1006A errors driver does not enable axis before taking measurements
- #13671: Error message during initialization of CXA N9000B signal analyzer
- #13672: RadiSense driver does not enable axis before taking measurements
- #13673: AR FM/FL field probe does not measure any field
- #13673: AR FM/FL field probe does not measure any field
- #13675: Object reference not set when referencing the input identifiers of the test site
- #13677: RadiSense IV returns E3 when setting the filter settings.
- #13682: Buttons for Add/Delete monitoring input in testsite configuration are shown too low
- #13683: HI6105 only returns the X axis measurement results
- #13684: Error 4 when retrieving field with RadiSense 4
- #13696: Reading RadiSense 18 is slow
- #13697: Graph line colours are not remembered
- #13700: too much reflected power
- #13701: Signal generator error - R&S SMB 100A
- #13704: Communication with a RSS1018 in a RadiCentre 1 is very slow
- #13705: EUT Status Controller does not require that the response starts with TESTINFO
- #13706: Update screens shows new major while already up to date
- #13708: No communication with RadiCentre possible
- #13719: Object reference not set to an instance of an object
RadiMation version 2023.1.3[edit]
- #13459: Wrong value when measuring single final average detector from FPC1500
- #13534: Performance problems in 2022.1.3
- #13539: RadiSense Error 3 on LASER? command
- #13547: Design calibration import tool
- #13548: Implement calibration import tool
- #13549: Extend the calibration import tool to also support Schaffner calibration files
- #13550: Build 2023.1.x including Calibration import tool
- #13551: Document and explain how to import the calibration files from another software package
- #13583: Settings.ini has been corrupted
- #13611: Frankonia FC06.1 connection issue when initializing multiple driver instances on the same control unit
- #13702: RadiMation does not display correctly on non HD resolutions
RadiMation version 2023.1.2[edit]
- #6003: Check if a newer software version is available during startup
- #11491: When using field monitor application, no correction factors were used, despite them being selected
- #13314: Possibility to start a sequence from the commandline.
- #13444: Auto detect from Configuration screen does not update window.
- #13457: & in drivers release notes is shown as & in update check window
- #13576: Probe laser disconnect when testing above 1000 V/m
RadiMation version 2023.1.1[edit]
- #12695: Rename FormattedLong to FormattedInteger, Add new FormattedLong using int64 longs
- #12947: RadiMation slows down the PC after updating
- #13047: Starting RadiMation by opening an EUT-file, results in RadiLog not being able to start when requested
- #13255: Calculated electrical field using horn antenna, shows different measurement values when a test file is reopened