Release Notes/Solved items Version 2013.1
Jump to navigation
Jump to search
RadiMation version 2013.1.6[edit]
- #4604: R&S ESI as powermeter takes a very long time to measure 20 Hz
- #4603: TSF is marked as changed, even if nothing is changed
- #4602: Customization of the graphs restored to the default if 'Use this as default' is presssed
- #4600: Adjust the amplifier protection
- #4583: System calibration Attenuation / Gain Unhandled exeption error
- #4581: Frequency unit in the limitline configuration seems to be specified in Hz, but is interpreted as MHz
- #4580: Changes in the unit of a limitline are not directly updated in the grid with limitline values
- #4579: Limitlines with a dBpT unit are still shown as dBuV/m limitlines in a multiband emission test
- #4578: Limitlines configuration window doesn't show very small/big frequencies
- #4577: Multiband test is not able to change to the next testsite due to frequency limitations in the testsite
- #4501: H-Field with no measurement data
- #4500: Receiver is set to wrong reference level
- #4378: Error Software Protection Key when upgrading software
- #4371: Higher value then 1000 is not displayed in COR file
- #4285: Can't change order of the frequency band (MB) for sequence testing
- #4278: Crash during initialising R&S FSH6 Scanning Receiver
- #4169: AD Channels are swapped
- #4146: Changed sorting of AD channel configuration is confusing AD Convertor readout
- #4057: Copy to clipboard is forgetting the last item
- #4031: AD-Channels are changing after saving EUT
- #3455: Error message is displayed when changing from lower band to higher band with different equipment
- #3124: Double clicking the main window for reviewing the test sometimes opens a different test
- #2285: Port RadiMation to modern development tools (.NET)
- #708: new file is saved while No is selected.
RadiMation version 2013.1.5[edit]
- #4569: Reading out a powermeter in Free mode, is using maximum CPU load
RadiMation version 2013.1.4[edit]
- #4585: Possibility to dump the waveform of a LeCroy oscilloscope to a CSV file
- #4574: ESIB 26 preamp settings are not used
- #4536: Unhandled exception for object name icon
- #4535: Setting the preamplifier to 0 dB doesn't seem to be remembered
- #4533: Resizing main EUT test data columns is not correctly done
- #4504: Looping device check
- #4428: Error with ESI40 as powermeter
- #4396: Administrator password is unexpectedly changed/corrupted
- #4337: TDEMI soft-reset
- #4336: Abort scan on TDEMI
- #3573: Amplifier control panel can not be resized so you can see the complete status message
- #3304: Driver: AR 350AH1 (GPIB + USB)
RadiMation version 2013.1.3[edit]
- #4330 RI-SB manual mode, some texts are partly hidden
- #4529 Buttons are aligned on the right side, not very close to the other controls on the window
- #4444 .NET: cosmetic changes to setting windows
- #4368 not completely readable receiver settings should be extended
- #4249 .NET: window dimensions of settings can be completely resized
RadiMation version 2013.1.2[edit]
- #4513: The cancel button is not responding on the environmental window that is shown during the initialization
- #4512: Graph and table controls are not correctly initialized
- #4511: A 'Save As' dialog is displayed when the Powermeter window is closed in RadiMation Free
RadiMation version 2012.1.23[edit]
- #4491: Wrong LLF is removed
- #4485: Serial communication using Agilent IO libraries is not working
- #4459: .NET: visualisation frequency bands is not working correctly
- #4450: After installation it is still required to download and install .Net Framework 4
- #4448: Move message of restart of PC to the end of the setup program
- #4446: .NET: X+k*s module; issue with selection, calculation and crash
- #4445: Driver: LAN control of Maturo NCD Antenna Tower
- #4443 .NET: default window is showing events while unchecked
- #4441: .NET: crash after closing a new LLF without saving
- #4439 unlogically tab sequence for Default Address Information
- #4437: .NET: no information and wrong deleting of Cables
- #4436: .NET: no confirmation and wrong deleting of AD-channel(s)
- #4434: .NET: no menu and message descriptions dutch language
- #4433: .NET: adding and deleting two folders at once
- #4427: Driver: Agilent 54832B as an oscilloscope
- #4426: Driver: Agilent 54641A as an oscilloscope
- #4419: .NET: crash customized query customer database configuration
- #4407: .NET: crash while looking up EUT data
- #4402: .NET: typo tab Reports information line and Eut information
- #4393: .NET: Not all TSF files are deleted leaving a messed up EUT file and test summary
- #4383: .NET: confusing highlight selection
- #4376: .NET: LLF is not correctly showed
- #4373: .NET: when closing 'Select TSF'-window the 'New TSF'-window is opened
- #4367: .NET: crash after closing an adjusted test
- #4366: .NET: not possible to Save TSF when adjusting a test
- #4365: .NET: no 'save changes?' is asked when closing an adjusted test
- #4362: .NET: no units for modulation settings
- #4360: .NET: adjustment of constant power settings is not correctly done
- #4348: .NET: report generator arrow up/down doesn't work
- #4347: .NET: report generator can't use whole selection
- #4344: .NET: object reference error when using peak info table
- #4343: .NET: row is shifting up completely
- #4339: .NET: deleting a TSF file from list causes crash
- #4335: The up and down buttons in the Report Generator Configuration window are not working
- #4330: .NET: crash when test is directly closed after message
- #4318: .NET: some columns are reduced to an unreadable size
- #4315: .NET: some buttons, labels and text are misplaced
- #4314: .NET: when re-opening test re-selecting test equipment is needed
- #4313: .NET: folder name is changed to no description available
- #4312: .NET: screen unexpectedly disappear to background
- #4311: column width, location and sorting are unexpectedly changed
- #4310: sorting peak table information is illogical
- #4292: Can't include tests for X+k*s calculation
- #4289: .NET: Show Pulse Shape has wrong default window size/can be full resized in ESD, EFT and Surge
- #4288: Absence tab labels in ESD setting window
- #4266: Error and 'Loading Data' with ESD testing
- #4228: Issues frequency range, axis is not aligned ESMI receiver
- #4225: Issue Walter and Golterman field sensor EMR300
- #4203: Ignored settings powermeter gives incorrect measurement
- #4197: Send Crash dump dialog is shown when RadiMation is closed with visible sequence file
- #4191: HP33250A signal generator switching between -22 and -56dBm
- #4185: Readout of WG EMR 30 is not working
- #4138: Driver: Frankonia FC 05
- #4036: How should the CISPR25 measurement (with dBuV unit) be performed?
- #3813: using kV instead of v unit in ESD test
- #3712: Peak table sorting by frequency does not work correctly
- #3710: Sorting of peak table not saved
- #3638: Driver: Rohde & Schwarz HFH2-Z2
- #3600: sorting of peak table
- #3483: Sorting peaks according to frequency does not work correctly
- #2556: Changing different templates in the report window
- #1833: The peak-list at the end of the measurement should be sorted automatically (by Frequency)
RadiMation version 2012.1.22[edit]
- #4408: .NET: wrong frequencies measured during final peak measurement
- #4405: .NET: changes EUT info not recognized: no save confirmation
- #4404: .NET: specify error to 'can't write to file' or change in warning
- #4403: .NET: adjust the default row width
- #4395: .NET: Coax set Probably an unknown RadiMation Error
- #4382: Auto launch RadiMation doesn't close setup
- #4375: .NET: report generator creates strange signs
- #4369: Driver: PMM EP-600 with X, Y and Z-axis support
- #4350: .NET: report generator can't open when clicking on the Template file
- #4323: Information check failed error should be warning
- #4279: Wrong numeric data is exported
- #3931: Easily create a reference graph in emission measurements
- #3688: showing old measurement results during new measurement
- #3246: How to get the displayed data
RadiMation version 2012.1.21[edit]
- #4416: Change build-up of image points graph to logarithmic
RadiMation version 2012.1.20[edit]
- #4381: Driver: PMM EP-603
- #4357: .NET: modulation can't be turned off
- #4353: final peak measurement is done on wrong frequency with ESI40
- #2635: Starting level is not used when disabling the power delivery test
- #2630: Powerdelivery test cannot be disabled for Amplifier harmonic radical test
- #2113: Driver: RadiGen
RadiMation version 2012.1.19[edit]
- #4355: RadiPower is not detected correctly if NI-VISA is not installed
- #4351: .NET: report generator error object reference
- #4349: RadiPower device driver raises error: VISA received more event information of the specified type than the configured queue size could hold
- #4342: .NET: incompatibility of test results
- #4341: Driver: HI-6100 Field Monitor
- #4334: Driver: Amplifier Research FM 5004 communication issue
- #4331: When CTRL+A is pressed some unknown windows are shown
- #4327: Activate the calculated gain regulation as the default amplifier regulation
- #4326: .NET: improve view table information
- #4325: .NET: enlarge name information
- #4322: .NET: crash and wrong window name customer database configuration
- #4309: .NET: user color and thickness settings are not working
- #4308: .NET: equipment list is not updated
- #4295: Advanced options hows items as bold when it shouldn't
- #4294: Can't remove last EUT Information
- #4293: Remove new EUT Information does delete all
- #4291: Can't add Basic or Product standards
- #4286: Crash while checking communication R&S FSH3
- #4234: RadiCentre: unknown device type
- #4233: Readout of the RadiMate 4 hangs for a minute
- #4190: Zero frequency issue in the graph, testing from 40Hz
RadiMation version 2012.1.18[edit]
- #4363: Starting Level Signal generator can't be configurated
- #4297: Report Generator settings unexpectedly pop-up the Select template window
- #4296: Scrolling is disabled in EUT Information window
- #4249: Window dimensions of settings can be completely resized
- #4247: Display graph isn't working properly
- #4206: RadiMation is deleting the wrong test files
- #4078: Driver: HI6153
RadiMation version 2012.1.17[edit]
- #4298: Frequency range error NBM-520 Broadband Field Meter
- #4263: Claim that AR 50S1G4 doesn't exist
- #4262: Driver: Amplifier AR 40S1G4
- #4240: Error when calibration file is selected that is using another amplifier
- #4239: Not practical to have Multiband tests in a sequence
- #4229: Standard button selection after opening test data from EUT
- #4227: Driver: EMCO 5402 GTEM Cell
- #4224: Error report generation Data can not be pasted in Excel
- #4199: Showing the height graph in the RE Multiband test crashes the software
- #4192: Verify if CS106 test is not supported by RadiMation
- #3738: GUI pauses RI test
RadiMation version 2012.1.15[edit]
- #4222: Several errors with .NET version on Windows XP
RadiMation version 2012.1.11[edit]
- #4186: Command error (4198) during generation of report
RadiMation version 2012.1.9[edit]
- #4142: Testsite in band in multiband emission is reactivated even when no peaks should be detected
- #2952: Checkbox is not grayed out when viewing test results of Pulsed Immunity EFT
RadiMation version 2012.1.6[edit]
- #4080: Vertical grid lines of the graph are drawn on top of the measurements, which could hide measurement results
- #3457: Multiband menu name change
- #3396: Status screen to small for messages
- #2674: Popup menu in multiband test with list of test-sites is not sorted
- #611: Immunity Manual mode directly accessible from main menu
RadiMation version 2012.1.4[edit]
- #4438: .NET: two menu options will open same window
- #4287: Mast sometimes doesn't move with HD100 antenna controller
- #4178: TDEMI IF-Overload check
RadiMation version 2011.1.5[edit]
- #3453: The "Status" column, in the "Test Initialisation" dialog, is not sized correctly by default
- #2541: RF setting of the marconi 2023 does not check for errors
RadiMation version 5.9.0[edit]
- #3829: Driver for Amplifier Bonn BSA1050-250/100
- #3828: Unit is single band graph do not change after changing the unit in the unit configuration of the result file
- #3824: Configurable alarm detection is always reporting alarm, even when the correct response is returned.
- #3819: Network Analyser EUT Calibration, using a R&S ZVK, crashes with an overflow
- #3782: Driver: Antenna Schwarzbeck STLP 9128D and Elektromectrics EM 6954
- #3780: Driver: Pre amplifier Schwarzbeck BBV 9718
- #3755: RadiMation is setting up the ESPI with incorrect RBW during CI-testing
- #3746: Peak zoom-in doesn't seem to work in multiband emission
- #3745: Turntable doesn't turn a complete turn when it starts on a negative angle
- #3736: I can not select apply modulation outside dwell time when selecting pulse
- #3735: Driver: SCHWARZBECK TEMZ 5231
- #3734: Driver: schwarzbeck antenna's FESP 5132 + FESP 5133-7/41
- #3732: Driver: Milmega Rf1000
- #3724: Radisense 4 over RS232 does not set the filter setting
- #3720: During emission test: crosses instead of line
- #3701: Multiband Radiated Emission: Default value in dropdown list for Turntable Angle specifies 235°
- #3652: Driver: Kalmus LA200U
- #3651: Driver: Kalmus 122FC
- #3637: Driver: Logimetrics AN 8100Q
- #3636: Driver: Logimetrics AN8200G
- #3615: Multiband-Conducted Immunity: data is not displayed
- #3544: Device driver for Narda NBM550 uses the wrong baudrate
- #3447: Conducted Immunity Tests are slow in 5.5.7 in comparison to 5.3.18
- #3354: CARAD interface: two commands get combined to one
- #2597: In multiband immunity the cancel button only reacts on the end of the dwelltime
- #507: Overload indication of an analyser/receiver is not detected
RadiMation version 5.8.39[edit]
- #4411: VISA error while using USB communication for device