Release Notes/Solved items Version 2016.2.9

RadiMation version 2016.2.9[edit]

#2558: Driver RadiLink as cable
Driver: Agilent 34980A as an oscilloscope
#4063: Driver Milmega AS0860-15/25 RF usb controlled
#4076: RadiSense III not working
#4213: Driver EMControl Antenna tower
#4259: Driver: Configurable Field Probe doesn't work with HI6005
#4809: Driver: Hameg HMS3010 Spectrum Analyser
#6142: Driver: emtest UCS500N: Telecom line surge: 2 line / 4 line
#6356: Driver: FCC Bulk Current Injection probes
#6803: R&S ESU 40: Error -222: Data out of range FREQ:CW 4500 000 000 HZ
#6870: Driver HP 3458A Multimeter as AD Converter
#6970: Problems and overrange detected during CI Calibration
#7181: Driver: euro EMC RSC
#7244: Detect the 'Not referenced' state of the Maturo MCU controller
#7299: Selection of Input 2 for the TDEMI X
#7324: Prana MT400 Amplifier still in operate
#7325: Prana MT400 Amplifier not always to RF-ON
#7477: Driver: Bonn elektronik BLMA1060-50 Amplifier
#7604: Driver: BONN BLWA 0810-200/100 LAN
#7664: Unknown error: -1073807343
#7705: R&S SMT 06 Pulse modulation sometimes show a wrong pulse width setting
#7742: Amplifier Linearity test is not working when a variable testlevel is used during the calibration
#7771: R&S ESI as powermeter is measuring too fast
#7784: Preamplifier of Rigol DSA815 is not working in the GTEM test
#7814: Teseq PCJ 9201B: Unknown Device Driver
#7816: Driver Rohde & Schwarz BBA150 powermeter(s)
#7837: Driver: DARE!! Instruments BCI1004A
#7839: Settings to select 3 axes besides isotropic for Narda EMC 300 field probe
#7846: Ok button is not working caused by powermeter settings panel
#7850: RadiCentre 1 with RSS1006A controlled by RS232 is not working correctly
#7861: RadiSense is not working
#7862: Selecting an invalid baudrate doesn't raise a specific error message
#7864: Previous environmentaldata is not always remembered
#7865: Agilent SG 33120A is not turning on the output
#7871: Driver Rigol DSG830
#7872: Preamplifier on DSA832 cannot be activated during SB GTEM test
#7875: Driver CWS 500N3
#7891: Driver: Antenna ETS-LINDGREN GTEM 5317
#7895: TDEMI Device Not connected
#7900: Maturo MCU has slow communication
#7901: ControllerDelay for a GPIB controlled Maturo MCU can be 0
#7910: Extend PMM9010 driver to allow selection of CISPR-Average or (old-)Average as Average detector
#7914: Clicking on a peak in the emission frequency graph very often moves the frequency of the peak
#7920: Selection of DC Coupling on R&S ESW8 Input 2 is not possible
#7920: Selection of DC Coupling on R&S ESW8 Input 2 is not possible
#7923: Driver Agilent 3499A Switch Matrix
#7931: Catch BONN BSA 0110-100 EXECUTION_RESULT errors
#7933: Optimize communication with RadiGen
#7938: Signal generator VI modulation frequency is incorrectly set
#7941: Maturo NCD controller Device Not Connected
#7942: How to configure R&S BBA150 amplifier communication settings
#7943: 1000W1000 input invalid correction file
#7944: Ability to set a signal generator frequency offset for AnalyzerAsPowerMeterDecorator
#7952 Driver: R&S FSH 8 as readout unit for field probe
#7960: Receiver measurement from 500 kHz - 1800 kHz on the ESI results in a timeout
#7968: Radimation is working in "EFT Multiband" only. The test in "EFT" is not performed
$7972: RGN Data out of range error during initialization
#7979: Missing test equipment in the Report Generator
#7982: Ability to define a power offset for the RPR RadiPower
#7984: RadiCentre controlled devices are not setting the RadiCentre back to local
#7997: R&S URV35 Level Meter as AD Converter
#8002: Driver: ETS-Lindgren HI-6006 Field Sensor
#8010: Driver DARE!! Instruments BCI1004A Coupler
#8012: Environmental data window unable to press OK
#8013: Agilent Technologies E4432B: Not all bytes are written to the GPIB-Board within the timeout period (GPIB: EABO)
#8019 Compression EUT Calibration table export same for every compressionPoint
#8026: Driver: Hameg HMS3010 as Powermeter

Release Notes/Solved items Version 2016.2.9

RadiMation version 2016.2.9[edit]

Navigation menu

Search