Device Types
A/D converter[edit]
The A/D convertor is used to monitor the EUT during testing. All supported A/D converter devices can be found here
Absorbing Clamp[edit]
The absorbing clamp is used measure the conducted emission All absorbing clamp devices can be found here
Amplifier[edit]
The amplifier is used to generate power for immunity tests All supported amplifier devices can be found here
Antenna[edit]
The antenna is used to send or receive signals All supported antenna devices can be found here
Antenna Tower[edit]
The antenna tower is used to move the antenna in height and change the polarisation All supported antenna tower devices can be found here
Cable[edit]
The cable is used to enable signals paths to be better defined. You do not need to insert a cable, but especially for emissions it does give you a more accurate result. All supported cable devices can be found here
Calibration Antenna[edit]
The calibration antenna is used magnetic field calibration. All supported calibration antenna devices can be found here
Clamp Positioner[edit]
The clamp positioner is used position the absorbing clamp for the measurement All clamp positioner devices can be found here
Coupler[edit]
The coupler is used for coupling the power meter to be measured power. All supported coupler devices can be found here
Current Sensor[edit]
The current sensor is used for measuring the current in a cable. All supported current sensor devices can be found here
EFT Burst Generator[edit]
The EFT burst generator is used for recording the used generator. All supported EFT burst generator devices can be found here
ESD Generator[edit]
The ESD generator is used for recording the used generator. All supported ESD generator devices can be found here
EUT Controller[edit]
The EUT controller is used for controlling the EUT during immunity measurements All supported EUT controller devices can be found here
Field Sensor[edit]
The field sensor is used for measuring the field generated during a radiated immunity measurement. All supported field sensor devices can be found here
Forward Power Meter[edit]
The forward power meter is used for measuring the forward power during an immunity measurement. All supported forward power meter devices can be found here
Injection Device[edit]
The injection device is used for injecting the power into cables. All supported injection devices can be found here
Jig[edit]
The Jig is used for calibrating the injection devices. All supported Jig devices can be found here
LISN[edit]
The LISN is used for measuring conducted emissions All supported LISN devices can be found here
Modulation Source[edit]
The modulation source is used as an external modulator for the signal generator. All supported modulation source devices can be found here
Multimeter[edit]
The multimeter is used to monitor voltage over a coil during MIL STD testing. All supported multimeter devices can be found here
Network Analyser[edit]
The network analyser is used for specialized calibration tests. All supported network analyser devices can be found here
Oscilloscope[edit]
The oscilloscope is used to monitor voltage over a coil during MIL STD testing. All supported oscilloscope devices can be found here
Output Coupler[edit]
The output coupler is used for coupling the output power meter to be measured power, used in a strip line set up. All supported output coupler devices can be found here
Output Power Meter[edit]
The Output power meter is used for measuring the output power during an immunity measurement, used in a strip line set up. All supported output power meter devices can be found here
Pre Amplifier[edit]
The pre amplifier is used to amplify the incoming signals. All supported amplifier devices can be found here
Reflected Power Meter[edit]
The reflected power meter is used for measuring the reflected power during an immunity measurement. All supported forward power meter devices can be found here
Resistor[edit]
The resistor is used to monitor voltage over a coil during MIL STD testing. All supported resistor can be found here
Sensor Power Meter[edit]
The sensor power meter is used for measuring the power at the current sensor during an immunity measurement. All supported sensor power meter devices can be found here
Signal Generator[edit]
The signal generator is used to generate power for immunity tests. All supported signal generator devices can be found here
Spectrum Analyser[edit]
The spectrum analyser is used to receive the emission coming from the EUT. All supported spectrum analyser devices can be found here
Switch matrix[edit]
The switch matrix is used to create the signal path of the emitted or received signal All supported switch matrix devices can be found here
Turn Table[edit]
The Turn Table is used to turn the EUT in the correct position. All supported turn table devices can be found here