Release Notes/Solved items Version 2023.2
Jump to navigation
Jump to search
RadiMation version 2023.2.5[edit]
- #13291: Read all trace data when multiple detectors are active for a TDEMI
- #13512: Error of invalid process is not shown anymore after SHIFT+Advanced click
- #13536: Radimation 2022.3.6 crashs after each test when using two dongles.
- #13764: SG386 pulse modulation
- #13813: RadiMation hangs at the end of the test when multiple dongles are connected to the PC
- #13920: Driver request: Stanford Research SG386 RF Signal Generator
- #14005: Rigol RSA series: Additional sweep is taken after QP detector is activated to allow to level to correct amplitude
- #14010: Problem with RadiMation and the polarisation of the Frankonia FC06
- #14064: Rigol RSA series: Additional sweep is taken after QP detector is activated to allow to level to correct amplitude
- #14111: Driver: ETS-Lindgren EMSense 7007-203
- #14117: Apply cable correction to the magnetic field calibration
- #14121: Driver: A-info DS-3100
- #14122: Driver: A-Info LB-OH-650-10-C-SF
- #14123: Driver: A-Info LB-2080-SF
- #14124: Driver: Aeroflex 2025
- #14125: Driver: Agilent Technologies 83731A
- #14126: Driver: A-Info 62EWGS-A1
- #14127: Driver: A-Info 90EWG3.5-T02-A1
- #14128: Driver: EMC Partner ESD3000
- #14130: Driver: Tekbox current probes
- #14131: Driver: Tekbox Bulk current injection devices
- #14133: MCU antenna tower position progress calculation issue
- #14136: Driver: Injection device: Schloeder EMCL-20 and Schloeder EMCL-35
- #14148: High attenuation required for measuring the fundamental results in upper harmonics being measured in the noise.
- #14149: Adjust drivers to use the correct name for A-INFO
- #14154: Rigol DSA832: Additional sweep is taken after QP detector is activated to allow to level to correct amplitude
- #14156: Can HTTP communication be used to retireve information from JSON
- #14160: Rigol DSG3065B does not support SYST:ERR?
- #14161: Textronix AFG3251C reports event messages as errors
- #14166: HI-6105 cannot save settings when pressing the OK button
- #14176: CWS500 as receiver does not work
- #14177: Object reference error opening Graph Export window
- #14186: Error when using RS PRO analyzer as power meter
- #14194: Data returned from Tektronix TDS oscilloscopes are calculated using 10 vertical divisions
- #14194: Improved selection of to be transferred waveform from older Tektronix TDS oscilloscopes
- #14195: Driver: RadiSense RSS2010M
- #14199: HP E4419A cannot be found because the identification string cannot be changed
- #14201: EMSense 7007-203 drivers
- #14218: Wrong settings are sent to the VDI device
- #14223: HP E4419A dual power meter error during zero operation
- #14224: Process (PID number) not found after closing Notepad
- #14225: Frankonia FC06.1 wait after height change to finish INIT procedure
- #14226: Manual EFT configuration does not indicate the unit in which configured values are expressed
- #14229: Driver: Tekbox TBMA4
- #14230: Driver: Tekbox TBL 5032-3
- #14232: Driver: Kalmus 320 FC
- #14233: Driver: Kalmus 711-FC-CE
- #14234: Driver: Teseq T800
- #14235: Driver: FCC-801-M2-50A
- #14236: Driver: FCC-801-M3-16A
- #14237: Driver: FCC-801-M5-16A
- #14238: Driver: EM Test ESD 30
- #14243: Driver: Prana N-MT500DC
- #14245: Magnetic field test according ISO 11452-8 time outs when using the Configurable multimeter driver
- #14251: Adjusted start frequency to 9 kHz of Raditeq GTM0250A, GTM0500A and GTM1000A
- #14255: Powermeter Fail
- #14256: Regulation of initial step of a non linear amplifier is now using the configured default gain
- #14259: HP4418 added option to enable the step detector and send the sense speed
- #14261: Raise error if the selected filter setting is not allowed for current RadiPower firmware
- #14262: Driver: Hameg 8135
- #14263: R&S SMH Allow configuring of 10kHz-2GHz range
- #14265: Standard socket port of the Rigol RSA-series is port 5555
- #14267: Fix Strange layout of stirrer configuration panel
- #14268: Select tuned mode as the default stirrer type
- #14275: Driver: Boonton 4220 powermeter
- #14287: Driver: IFI T188-50
- #14288: Driver: Klein+Hummel SA602 amplifier
- #14289: Driver: OPHIR RF 5041
RadiMation version 2023.2.4[edit]
- #5383: Implement 'Ignore height change' settings for the NCD AT
- #6879: Maturo MCU cannot ignore height change
- #9153: Average too high in Final Measurement sweep
- #9332: Final Measurement - average
- #12081: Average of phase is not correctly calculated when Phase is crossing 180 degrees
- #12150: AD-Convertor device driver as a Decorator around a spectrum analyser driver to measure AM/FM/Pulse-modulation
- #12236: Driver: Rigol RSA5065 to use multiple traces in EMI mode
- #12482: Support tracking generator on Rigol RSA5065
- #12797: Driver: Rigol RSA5065 EMI-Mode
- #12799: Rigol RSA5065 Tracking generator
- #13049: Driver: Siglent SVA1032X
- #13402: Measurement using Cispr AVG detector in the EMI-Mode of the Rigol RSA5065N
- #13602: I/O Error with Rigol RSA5065
- #13688: It takes long to open emission data files
- #13749: Report generator deletes grid found in template file when generating report
- #13772: Driver: Agilent 34410A
- #13844: Driver: Spectrum analyser driver for multimeter in CWS500N3
- #13857: Qpeak not visible in peak table after making adjustments to the peak table.
- #13883: Unexpected oscilloscope behavior in CS101 test
- #13987: Re-implement MCU antenna tower limits as pure software limits,
- #13924: The name or number of the point in the UFA calculation cannot be modified
- #13932: Differences in generated reports
- #13939: Include more logging during start of RadiMation to identify what causes startup time
- #13956: The last used graph exporter type should be remembered
- #13983: Environmental information is inserted as boolean value in RI printout reports
- #14000: Rigol RSA5065 Communication Error
- #14017: Driver: KRE 4000 extend with ethernet control
- #14031: RadiSense has invalid user calibration table.
- #14038: Implemented a change to not reduced the sweep time when the average or rms detector is activated for r&s esu based drivers like the esw
- #14041: It is not possible anymore to use a key on the keyboard to select an entry from a dropdown list
- #14053: RSA5065(EMI mode): RBW cannot be set to 9 kHz, changes back to 1 MHz
- #14054: AR FM5004 Driver issue with channel selection
- #14055: conducted emission in RSA5065 EMI mode
- #14058: RE MB QP missing in the table
- #14063: FA 7006 Issue with termination characters on legacy commands
- #14076: Hide the "Move antenna height" and Move distance" setting from the change order
- #14080: Driver: Siglent SSG5060X
- #14081: Radiated Immunity MB test is corrupt in 2023.2.3
- #14082: Plugin cards are not auto detected in RadiCentre Ultra 8
- #14085: Add Advanced option:"Emission.Multiband.Sequence.AllowPeakReview"
- #14086: Driver PMM 6630 does not handle *** correctly
- #14092: Improvement Amplifier linearity, remove 10dB Limit?
- #14095: Driver: ETS-Lingren 3166 & 3167 TEM Horn antennas
- #14097: Multiband GTEM not possible to configure the antenna distance
- #14099: Emission test using Rigol RSA5065 - Analyzer Reference Level not as defined
- #14100: RadiCentre returns VI_INP_PROT error when the expected response size is less than the actual response size
- #14102: Averaging of phase
- #14113: ESD Keywords are not working
- #14114: Repetition rate has no unit in report in EFT Report.
- #14116: More antenna steps in MB GTEM test results in unexpected results
- #14119: Turn table min/max positions are incorrect
- #14175: Antenna with Power Meter as "Field Probe"
- #14206: Change LumiLoop 2.0 calibration mode to put back the original settings after the test.
- #14207: Electrical Field could not be regulated to the desired test-level
- #14210: Improved auto attenuator selection on R&S ESW input 2 with pulse limiter
- #14211: DSG3065B raises error when am modulation is used above 3.6 GHz
- #14242: Time out error controlling the U2009A power meter
- #14249: EUT Controller TESTINFO doesn't work
- #14277: Error setting the sweep time while using the CAV detector
RadiMation version 2023.2.3[edit]
- #12894: OPC Driver does not work
- #13901: ESIB 7 error
- #13913: Extend Bonn amplifier driver to reset water cooling interlock error at retry
- #13925: The start position should be allowed to be higher than the end position of the X-orientation of the probe positioner
- #13926: The start position should be allowed to be higher than the end position of the Y-orientation of the probe positioner
- #13938: Change the x-position and the y-position generator to behave as an uni-directional generator by default
- #13951: Extend manual or add application note regarding usage of axis specific correction factors of field probes
- #13955: Add 4 steps as a default possible options for the XY positioner step count
- #13957: ESR TD driver has a resolution configuration which is not expected
- #13965: UFA Calculation not possible due to unspecified tolerance in calibration files - Field closed loop method
- #13966: Maturo NCD turntable time expired before operation completed
- #13978: Multiband: UFA calibration seems to regulate to an average field greater than the specified tolerance
- #13996: index outside the bounds
- #14011: Maturo NCD Turntable: Timeout expired before operation completed.
- #14012: EMPower 7002-009 010 option 010 not detected
- #14016: Extend the Maturo NCD Antenna tower to send the height with fractions.
- #14023: R&S ESRP3 Analyser has a default port of 7895 this should be 5025
- #14026: Amplifier Research FL 7006: Not all bytes are written to the GPIB-Board within the timeout period (GPIB: EABO)
- #14029: EN61000-4-3:2020 Constant Power method is interpreted as being constant field method in the UFA configuration dialog
- #14033: Driver: Raditeq GTEM RGT0250A, RGT0500A, RGT1100A
- #14049: Configurable Power meter clear input buffers before getpower.
- #14052: RSA5065(GPSA mode) is not switching to EMI mode for the final detector measurement
- #14067: Support RF mixer in front of Keysight N9020B MXA
- #14145: RadiMation cannot connect to the R&S NRP powermeters anymore
RadiMation version 2023.2.2[edit]
- #13849: Manual XY Positioner does not show message when first position is X=0, Y=0
- #13851: The tab order of the X/Y positioner settings of the field distribution is very unlogical
- #13584: The virtual X/Y-positioner has advanced configuration settings which is unlogical
- #13858: Setting start-x and end-x in Field Distribution configuration is not possible
- #13877: NGS3040 set default port configuration to 1025
- #13934: CTR1009B USB drivers
RadiMation version 2023.2.1[edit]
- #9240: Negative combobox values with unit distance (grootheid) are getting different smaller units (eenheden)
- #9241: Spin control of ctlsetting xy positioner comboboxes only checks closest allowed value when the unit is not centimeters
- #9243: BusyStatusBar of the xy positioner progression status displays the distances with the wrong units as extension
- #9832: Driver Maturo FPP2.3 Biaxial Positioner
- #12157: EN 61000-4-3:2020 is not mentioned in the UFA calculation window
- #13408: XY positioner parameters are reset during configuration
- #13411: The continue settings for the XY positioner only shows a selection for the X position
- #13502: Restrict usage of XY positioner using RadiMation Essential license
- #13503: Change the order of the XY positioner configuration controls
- #13504: Possibility to enter the positioner distances with millimeter accuracy
- #13505: Set the correct values for the XY positioner in the advanced settings
- #13506: Show and use the X position setting in the change order
- #13507: Show and use the Y position setting in the change order
- #13508: Separation of command generators, applicable settings and driver interfaces for the X- and Y-axis movement of a field probe positioner device driver
- #13510: Add switch matrix events related to the Y positioning of the field probe positioner
- #13511: Add switch matrix events related to the X positioning of the field probe positioner
- #13513: Show the antenna and antenna tower controls when the field distribution location type is selected
- #13631: Add a stop button for the manual mode XY- Positioner
- #13632: Parallel control of current, voltage, switch matrix and eut controller
- #13634: UFA calibration export tool
- #13736: EN 61000-4-3:2020 is not mentioned in the UFA calculation window
- #13741: IEC 61000-4-3:2020 specifies that the amplifier is linear if the 5.1 dB step results in a 3.1 to 7.1 dB change
- #13791: Calculate average and float unit test fails in VS 2022
- #13805: Calibration export tool file validators, keeps detecting already deleted cal files