Difference between revisions of "Device Types"
| Line 1: | Line 1: | ||
= A/D converter = | = A/D converter = | ||
The A/D convertor is used to monitor the EUT during testing. All supported A/D converter devices can be found [[:Category:AD Convertor|here]] | The A/D convertor is used to monitor the EUT during testing. All supported A/D converter devices can be found [[:Category:AD Convertor|here]] | ||
| + | |||
| + | = Absorbing Clamp = | ||
| + | The absorbing clamp is used measure the conducted emission | ||
| + | All absorbing clamp devices can be found [[:Category:Absorbing Clamp|here]] | ||
| + | |||
| + | = Clamp Positioner = | ||
| + | The Clamp Positioner is used measure the conducted emission | ||
| + | All absorbing clamp devices can be found [[:Category:Absorbing Clamp|here]] | ||
= Amplifier = | = Amplifier = | ||
The amplifier is used to generate power for immunity tests | The amplifier is used to generate power for immunity tests | ||
| − | All supported amplifier | + | All supported amplifier devices can be found [[:Category:Amplifier|here]] |
= Antenna = | = Antenna = | ||
| Line 57: | Line 65: | ||
The switch matrix is used to create the signal path of the emitted or received signal | The switch matrix is used to create the signal path of the emitted or received signal | ||
All supported switch matrix devices can be found [[:Category:Switch Matrix|here]] | All supported switch matrix devices can be found [[:Category:Switch Matrix|here]] | ||
| + | |||
| + | = Turn Table = | ||
| + | The Turn Table is used to turn the [[EUT]] in the correct position. | ||
| + | All supported turn table devices can be found [[:Category:Turn Table|here]] | ||
Revision as of 12:21, 19 December 2007
Contents
- 1 A/D converter
- 2 Absorbing Clamp
- 3 Clamp Positioner
- 4 Amplifier
- 5 Antenna
- 6 Antenna Tower
- 7 Calibration Antenna
- 8 Coupler
- 9 EUT Controller
- 10 Forward Power Meter
- 11 Modulation Source
- 12 Multimeter
- 13 Oscilloscope
- 14 Reflected Power Meter
- 15 Resistor
- 16 Signal Generator
- 17 Switch matrix
- 18 Turn Table
A/D converter
The A/D convertor is used to monitor the EUT during testing. All supported A/D converter devices can be found here
Absorbing Clamp
The absorbing clamp is used measure the conducted emission All absorbing clamp devices can be found here
Clamp Positioner
The Clamp Positioner is used measure the conducted emission All absorbing clamp devices can be found here
Amplifier
The amplifier is used to generate power for immunity tests All supported amplifier devices can be found here
Antenna
The antenna is used to send or receive signals All supported antenna devices can be found here
Antenna Tower
The antenna tower is used to move the antenna in height and change the polarisation All supported antenna tower devices can be found here
Calibration Antenna
The calibration antenna is used magnetic field calibration. All supported calibration antenna devices can be found here
Coupler
The coupler is used for coupling the power meter to be measured power. All supported coupler devices can be found here
EUT Controller
The EUT controller is used for controlling the EUT during immunity measurements All supported EUT controller devices can be found here
Forward Power Meter
The forward power meter is used for measuring the forward power during an immunity measurement. All supported forward power meter devices can be found here
Modulation Source
The modulation source is used as an external modulator for the signal generator. All supported modulation source devices can be found here
Multimeter
The multimeter is used to monitor voltage over a coil during MIL STD testing. All supported multimeter devices can be found here
Oscilloscope
The oscilloscope is used to monitor voltage over a coil during MIL STD testing. All supported oscilloscope devices can be found here
Reflected Power Meter
The reflected power meter is used for measuring the reflected power during an immunity measurement. All supported forward power meter devices can be found here
Resistor
The resistor is used to monitor voltage over a coil during MIL STD testing. All supported resistor can be found here
Signal Generator
The signal generator is used to generate power for immunity tests All supported signal generator devices can be found here
Switch matrix
The switch matrix is used to create the signal path of the emitted or received signal All supported switch matrix devices can be found here
Turn Table
The Turn Table is used to turn the EUT in the correct position. All supported turn table devices can be found here
