Difference between revisions of "RadiMation Application Note 102"
| Line 2: | Line 2: | ||
This application note explains how a MIMO measurement can be performed with {{RadiMationFree}} as it is described in the [[ETSI EN300328]]. | This application note explains how a MIMO measurement can be performed with {{RadiMationFree}} as it is described in the [[ETSI EN300328]]. | ||
| − | + | It is assumed that device drivers for the used powermeters are already configured in the configuration of {{RadiMation}}. Otherwise see [[Chapter 2#Device driver configuration| Device driver configuration]] in [[Chapter 2]] of the {{RadiMation}} [[Manual]]. | |
| − | {{ | ||
| − | + | Create a new EUT-file by selecting from the menu bar: | |
| + | {{Menu|File|New|EUT}} | ||
| + | Specify a filename for the new [[EUT]]-file and select {{ScreenElement|OK}}. A new EUT-window will now be opened. | ||
| + | |||
| + | To start the Burst measurement select from the menu bar: | ||
{{Menu|Tests|Radiated Emission|Burst}} | {{Menu|Tests|Radiated Emission|Burst}} | ||
| − | Press {{ScreenElement|New}} to create a new TSF-file | + | Press {{ScreenElement|New}} to create a new [[TSF]]-file. |
A new window will now be opened in which the test can be configured. | A new window will now be opened in which the test can be configured. | ||
* Press the {{ScreenElement|+ Add}} button to add all the power meters to your test. | * Press the {{ScreenElement|+ Add}} button to add all the power meters to your test. | ||
| − | * Enter the correct parameters on the right hand side: | + | * Enter the correct parameters on the right hand side:{{ScreenElementDescriptionStart}} |
| − | + | {{ScreenElementDescription|Frequency|Different [[Device Types|types]] of devices are available in {{RadiMation}}. Only the created device drivers of the type that is selected for {{ScreenElement|Device Driver Type}} will be shown in the list}} | |
| − | + | {{ScreenElementDescription|Trigger level|Shows a list of all the available device drivers for the selected {{ScreenElement|Device Driver Type}}}} | |
| − | + | {{ScreenElementDescription|etc.....|Creates a new [[RadiMation|{{RadiMation}}]] device driver for a specific device. It is only possible to create a new device driver for the selected {{ScreenElement|Device Driver Type}}.}} | |
| − | + | {{ScreenElementDescriptionEnd}} | |
Revision as of 13:52, 2 December 2014
Performing an ETSI EN300328 MIMO measurement
This application note explains how a MIMO measurement can be performed with RadiMation® Free as it is described in the ETSI EN300328.
It is assumed that device drivers for the used powermeters are already configured in the configuration of RadiMation®. Otherwise see Device driver configuration in Chapter 2 of the RadiMation® Manual.
Create a new EUT-file by selecting from the menu bar:
-
File
- New
- EUT
-
-
-
Specify a filename for the new EUT-file and select OK. A new EUT-window will now be opened.
To start the Burst measurement select from the menu bar:
- Tests
- Radiated Emission
- Burst
-
-
-
Press New to create a new TSF-file. A new window will now be opened in which the test can be configured.
- Press the + Add button to add all the power meters to your test.
- Enter the correct parameters on the right hand side:
 Frequency
|
Different types of devices are available in RadiMation®. Only the created device drivers of the type that is selected for Device Driver Type will be shown in the list |
| Trigger level
|
Shows a list of all the available device drivers for the selected Device Driver Type |
| etc.....
|
Creates a new RadiMation® device driver for a specific device. It is only possible to create a new device driver for the selected Device Driver Type. |
Press Start Test to start the measurement test with multiple power meters. Enter a filename to save the TSF-file, so it can be used again in the future.
After a measurement has been performed, all parameter such as Max e.i.r.p, medium utilisation, Duty cycle, Min Gap time and Max. Sequence time and RMS are calculated by RadiMation®.
