Difference between revisions of "RadiMation Application Note 102"
| Line 6: | Line 6: | ||
Create a new EUT-file by selecting from the menu bar: | Create a new EUT-file by selecting from the menu bar: | ||
{{Menu|File|New|EUT}} | {{Menu|File|New|EUT}} | ||
| + | |||
Specify a filename for the new [[EUT]]-file and select {{ScreenElement|OK}}. A new EUT-window will now be opened. | Specify a filename for the new [[EUT]]-file and select {{ScreenElement|OK}}. A new EUT-window will now be opened. | ||
| Line 11: | Line 12: | ||
{{Menu|Tests|Radiated Emission|Burst}} | {{Menu|Tests|Radiated Emission|Burst}} | ||
| − | Press {{ScreenElement|New}} to create a new [[TSF]]-file. | + | [[File:SelectRadiatedEmissionBurstFromMenu.png]] |
| − | + | ||
| − | A new window will now be opened in which the test can be configured. | + | Press {{ScreenElement|New}} to create a new [[TSF]]-file. |
| + | |||
| + | A new window will now be opened in which the burst test can be configured. | ||
| + | |||
| + | [[File:RadiatedEmissionBurstTSF.png]] | ||
| + | |||
* Press the {{ScreenElement|+ Add}} button to add all the power meters to your test. | * Press the {{ScreenElement|+ Add}} button to add all the power meters to your test. | ||
* Enter the correct parameters on the right hand side:{{ScreenElementDescriptionStart}} | * Enter the correct parameters on the right hand side:{{ScreenElementDescriptionStart}} | ||
| Line 21: | Line 27: | ||
{{ScreenElementDescriptionEnd}} | {{ScreenElementDescriptionEnd}} | ||
| − | |||
Press {{ScreenElement|Start Test}} to start the measurement test with multiple power meters. | Press {{ScreenElement|Start Test}} to start the measurement test with multiple power meters. | ||
Enter a filename to save the TSF-file, so it can be used again in the future. | Enter a filename to save the TSF-file, so it can be used again in the future. | ||
| + | The measurement is then started and the results are shown in the graph. | ||
| − | + | [[File:RadiatedEmissionBurstResult.png]] | |
| − | |||
| − | |||
| − | |||
| + | During the measurement, all parameter such as Max e.i.r.p, medium utilisation, Duty cycle, Min Gap time and Max. Sequence time and RMS are calculated and shown. | ||
| + | When the measurement is finished configuration parameters can be changed if desired, and a new measurement can be triggered by pressing the {{ScreenElement|Trigger}} button. | ||
| + | The measurement results can be saved into the created EUT file by pressing the {{ScreenElement|Close}} button. | ||
[[Category:RadiMation Application Note]] | [[Category:RadiMation Application Note]] | ||
[[Category:RadiMation]] | [[Category:RadiMation]] | ||
Revision as of 14:02, 2 December 2014
Performing an ETSI EN300328 MIMO measurement
This application note explains how a MIMO measurement can be performed with RadiMation® Free as it is described in the ETSI EN300328.
It is assumed that device drivers for the used powermeters are already configured in the configuration of RadiMation®. Otherwise see Device driver configuration in Chapter 2 of the RadiMation® Manual.
Create a new EUT-file by selecting from the menu bar:
-
File
- New
- EUT
-
-
-
Specify a filename for the new EUT-file and select OK. A new EUT-window will now be opened.
To start the Burst measurement select from the menu bar:
- Tests
- Radiated Emission
- Burst
-
-
-
Press New to create a new TSF-file.
A new window will now be opened in which the burst test can be configured.
- Press the + Add button to add all the power meters to your test.
- Enter the correct parameters on the right hand side:
 Frequency
|
Different types of devices are available in RadiMation®. Only the created device drivers of the type that is selected for Device Driver Type will be shown in the list |
| Trigger level
|
Shows a list of all the available device drivers for the selected Device Driver Type |
| etc.....
|
Creates a new RadiMation® device driver for a specific device. It is only possible to create a new device driver for the selected Device Driver Type. |
Press Start Test to start the measurement test with multiple power meters.
Enter a filename to save the TSF-file, so it can be used again in the future.
The measurement is then started and the results are shown in the graph.
During the measurement, all parameter such as Max e.i.r.p, medium utilisation, Duty cycle, Min Gap time and Max. Sequence time and RMS are calculated and shown. When the measurement is finished configuration parameters can be changed if desired, and a new measurement can be triggered by pressing the Trigger button.
The measurement results can be saved into the created EUT file by pressing the Close button.
