Difference between revisions of "List of Application Notes"
| Line 38: | Line 38: | ||
* Application Note 136: [[RadiMation Application Note 136|RadiMation Support using Microsoft Teams]] | * Application Note 136: [[RadiMation Application Note 136|RadiMation Support using Microsoft Teams]] | ||
* Application Note 137: [[RadiMation Application Note 137|Perform a Field uniformity and TEM mode verification in RadiMation]] | * Application Note 137: [[RadiMation Application Note 137|Perform a Field uniformity and TEM mode verification in RadiMation]] | ||
| − | * Application Note 138: [[RadiMation Application Note 138|How to perform magnetic field close proximity | + | * Application Note 138: [[RadiMation Application Note 138|How to perform a magnetic field close proximity test]] |
[[Category:RadiMation Application Note]] | [[Category:RadiMation Application Note]] | ||
[[Category:RadiMation]] | [[Category:RadiMation]] | ||
Revision as of 07:33, 31 January 2022
The following application notes are present:
- Application Note 100: Enhanced Status Window
- Application Note 101: Optimize Height and Optimize Angle
- Application Note 102: Performing an ETSI EN300328 MIMO measurement
- Application Note 103: How to determine the antenna diagram of an antenna
- Application Note 104: How to determine the transfer impedance of a current sensor
- Application Note 105: Protection of changes in the RadiMation® configuration
- Application Note 106: Powermeter parameter configuration
- Application Note 107: How to provide detailed information of problems
- Application Note 108: How to perform a verification of calculations in RadiMation®
- Application Note 109: Configuration of RadiMation® on a network
- Application Note 110: How to perform Uniform Field Area (UFA) calculations
- Application Note 111: How to use the RadiCentre® safety interlock system in RadiMation®
- Application Note 112: How to perform Audio Break Through measurements
- Application Note 113: How to use the RadiMation® Global and Standalone configuration manager
- Application Note 114: How to measure data from the EUT using the Configurable AD Convertor device driver
- Application Note 115: How to measure amplifier harmonics using RadiMation®
- Application Note 116: How to specify the antenna factor
- Application Note 117: How to update device drivers
- Application Note 118: How to request device driver creation
- Application Note 119: How to basic configure a device
- Application Note 120: How to measure the HV-LV coupling attenuation
- Application Note 121: Using a RadiPower powermeter stand-alone with RadiMation® free
- Application Note 122: Updating RadiMation®
- Application Note 123: Implementing the control of a switch matrix in RadiMation®
- Application Note 124: Emission: Measuring intermittent signals
- Application Note 125: Pontis Pecos: Using the Pontis Pecos device driver
- Application Note 126: Gain Compression
- Application Note 127: Report Generator: Build a custom emission table
- Application Note 128: Reading the output value of single antenna's separately of a isotropic probe
- Application Note 129: How to use the Schloeder CDG 6000
- Application Note 130: How to use the RadiMation® Amplifier Control Window
- Application Note 131: How to perform HV/LV Coupling measurements in RadiMation® according to CISPR25
- Application Note 132: How to change the default EUT-Information fields
- Application Note 133: How to use EUT monitoring in Pulsed Immunity MultiBand EFT & Surge RadiMation
- Application Note 134: How to use frequency change mode:Ramp for Radiated Immunity MultiBand
- Application Note 135: How to program the RadiSense 10 Calibration table
- Application Note 136: RadiMation Support using Microsoft Teams
- Application Note 137: Perform a Field uniformity and TEM mode verification in RadiMation
- Application Note 138: How to perform a magnetic field close proximity test
