List of Application Notes

The following application notes are present:

• Application Note 100: Enhanced Status Window
• Application Note 101: Optimize Height and Optimize Angle
• Application Note 102: Performing an ETSI EN 300 328 MIMO measurement
• Application Note 103: How to determine the antenna diagram of an antenna
• Application Note 104: How to determine the transfer impedance of a current sensor
• Application Note 105: Protection of changes in the RadiMation^® configuration
• Application Note 106: Powermeter parameter configuration
• Application Note 107: How to provide detailed information of problems
• Application Note 108: How to perform a verification of calculations in RadiMation^®
• Application Note 109: Configuration of RadiMation^® on a network
• Application Note 110: How to perform Uniform Field Area (UFA) calculations
• Application Note 111: How to use the RadiCentre® safety interlock system in RadiMation^®
• Application Note 112: How to perform Audio Break Through measurements
• Application Note 113: How to use the RadiMation^® Global and Standalone configuration manager
• Application Note 114: How to measure data from the EUT using the Configurable AD Convertor device driver
• Application Note 115: How to measure amplifier harmonics using RadiMation^®
• Application Note 116: How to specify the antenna factor
• Application Note 117: How to update device drivers
• Application Note 118: How to request device driver creation
• Application Note 119: How to basic configure a device
• Application Note 120: How to measure the HV-LV coupling attenuation
• Application Note 121: Using a RadiPower powermeter stand-alone with RadiMation^® free
• Application Note 122: Updating RadiMation^®
• Application Note 123: Implementing the control of a switch matrix in RadiMation^®
• Application Note 124: Emission: Measuring intermittent signals
• Application Note 125: Pontis Pecos: Using the Pontis Pecos device driver
• Application Note 126: Gain Compression
• Application Note 127: Report Generator: Build a custom emission table
• Application Note 128: Reading the output value of single antenna's separately of a isotropic probe
• Application Note 129: How to use the Schloeder CDG 6000
• Application Note 130: How to use the RadiMation^® Amplifier Control Window
• Application Note 131: How to perform HV/LV Coupling measurements in RadiMation® according to CISPR25
• Application Note 132: How to change the default EUT-Information fields
• Application Note 133: How to use EUT monitoring in Pulsed Immunity MultiBand EFT & Surge RadiMation
• Application Note 134: How to use frequency change mode:Ramp for Radiated Immunity MultiBand
• Application Note 135: How to program the RadiSense 10 calibration table
• Application Note 136: RadiMation Support using Microsoft Teams
• Application Note 137: Perform a Field uniformity and TEM mode verification in RadiMation
• Application Note 138: How to perform a magnetic field close proximity test
• Application Note 139: How to perform a magnetic field close proximity test using forward power levelling
• Application Note 140: How to perform a closed loop magnetic field test
• Application Note 141: How to create and apply a cable correction
• Application Note 142: Investigate and resolve Windows USB driver problems for Raditeq equipment
• Application Note 143: Using the Teseq NSG 4060 low frequency immunity test system in RadiMation^®
• Application Note 144: How to set up RadiMation^® to use a measurement device connected to a different PC
• Application Note 145: How to perform a MIL-STD-461 RE102 Radiated Emission test
• Application Note 146: Configuring device drivers to check the interlock state of Bonn and R&S amplifiers
• Application Note 147: How to perform a MIL-STD-461 RE101 Radiated Emission test
• Application Note 148: How to perform a MIL-STD-461 CE101 Conducted Emission test
• Application Note 149: How to perform a MIL-STD-461 CE102 Conducted Emission test
• Application Note 150: Automated calibration of the Uniform Field Area (UFA) with an electric field probe positioner
• Application Note 151: How to use the graph exporter to export measurement data into calibration files
• Application Note 152: Creating back-ups of important RadiMation files
• Application Note 153: Using Multi axis field corrections
• Application Note 154: How to perform a MIL-STD-461 CS114, Conducted susceptibility, bulk cable injection test
• Application Note 155: How to perform a MIL-STD-461 CS109, Conducted susceptibility, structure current test
• Application Note 156: How to perform a Radiated emission substitution test
• Application Note 157: How to perform a MIL-STD-461 RS103, radiated susceptibility, electric field
• Application Note 158: How specific devices can be excluded from the table of used equipment in the report
• Application Note 159: How to create a formatted table in a report
• Application Note 160: How to perform a ISO 11452-4, bulk cable injection test
• Application Note 161: Information about antenna spurious harmonics testing with RadiMation^®